Author Topic: Well here it is  (Read 28385 times)

0 Members and 1 Guest are viewing this topic.

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: Well here it is
« Reply #60 on: September 19, 2010, 04:13:11 PM »
Well there were a few things with the engine: nothing left of the gasket under the cylinders  :o and the inlet valves were totally worn. So bought 4 new valves (wasn't easy to find them) and took it to a place called dr. motor where it was skimmed and the new valves were put in (seats repaired etc.) The guides are still good and so are the springs. Nice and clean now  :) Cleaned the block and the engine got new gaskets.(cyl head, oil sump, rocker cover etc). Changed the big end bearings too as they were all worn (the crankshaft journals  are however like new).
Couldn't take off the crankshaft pulley unfortuently to check the seals and timing chain but no oil dripping so far. Had to replace one pushrod and the rocker adjusting screw as the hemi sphereical/ball joint part had broken off (cyl 2 exhaust rocker once jumped off the valve so i guess that's when it happened...) Rockers were sanded/grinded too.
Head is now on, so is everything else. In the meantime i painted the fan and other covers that i didn't do previously.

"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: Well here it is
« Reply #61 on: September 19, 2010, 04:17:37 PM »
Changed the float in the carb as it was cracked in 3 places and had petrol in it. Changed the needle and seat too.
Put the interior together the rear seat got a new vinyl cover which looks good. Only thing left is the drivers side floor carpet (hope to get a new one) and put in the drivers seat and seatbelt.
Pulled the dynamo apart. Changed the brushes and bearings, had the collecter part machined.

« Last Edit: September 19, 2010, 06:28:10 PM by GTMaster »
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: Well here it is
« Reply #62 on: September 19, 2010, 04:24:40 PM »
That's all the pics i have now. The indicators and lights are fitted and working. Manged to break a headlight when fitting it  >:( That felt good, :oops: it was an original Wessem type not the halogen type headlight. Managed to get another pair from the breakers but they're becoming rare.
Still have to repair the steering mech as it's leaking oil. Have a seal kit for it just need to take the steering arm off it first (getting a tool for that, also bought a torque wrench for the cyl head  ;D)

Happy i've come this far, only the finishing touches remain. Stumbled upon a pair of Wessem rectangular halogen foglights in the shed. Having thoughts of fixing those and fitting them.... but that'll be something else for the near future  :)
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

smallcox

  • Super Member
  • ***
  • Posts: 433
  • Karma: 4
Re: Well here it is
« Reply #63 on: September 19, 2010, 04:46:50 PM »
Hi GTMaster,

Must be nearly there, but I quess it's that last 10 percent that seems to take forever. >:(

Got the engine started yet?

Smallcox
air cooled, gt15 garret turbo with intercooler, 14x9" wheels with 225/40/14 toyos, front arb and disc brakes

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: Well here it is
« Reply #64 on: September 19, 2010, 06:25:01 PM »
Hi!
Yes have started the engine. Was interested in how it would start as i forgot to mention that i pulled the top half of the fuel pump apart as it was full of this dirt like stuff. I measured how much of the rod sticks out and put 0.2mm thinner gasket paper so i reckon fuel pressure should be good now (didn't have problems with it before  though). As soon as it sucked up the fuel it started without a problem and runs good, just i don't like its idle. It seems to run smoother at a higher idle rpm, but i'll put it onto an emission test and adjust the CO. When i move the throttle a bit it stutters for like half a second before picking up rpm but then goes all the way, up and down, without a problem  ;D  8) The engine gives out a puff of black smoke too when i floor it, so i'll still have to play around with it. Still need to change the condenser coil as it's making nice sparks through the whole rev range (from small ones to large ones). Tried three used coils with no luck. Got a new one just have to fit it and test it.
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

smallcox

  • Super Member
  • ***
  • Posts: 433
  • Karma: 4
Re: Well here it is
« Reply #65 on: September 19, 2010, 06:46:03 PM »
 
It's not unusual that the engine hesitates when you push the throttle,because theres no pump jet built into these carbs so go lean on mixture when the throttle is pressed :(

Good news your running, now how long before your on the road?
air cooled, gt15 garret turbo with intercooler, 14x9" wheels with 225/40/14 toyos, front arb and disc brakes

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: Well here it is
« Reply #66 on: September 19, 2010, 07:11:00 PM »
Yeah i know how it hesitates, sometimes played with it (pushed it to the floor suddenly then let go. It made a puff every time  :P) This time however i move the throttle slowly and it doesn't rev up smoothly for a split second from idle.
Hopefully be complete by the end of the month. Though i've missed all my deadlines that i set up for myself so I won't be surprised if it will be on the road in the first week of October...
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

smallcox

  • Super Member
  • ***
  • Posts: 433
  • Karma: 4
Re: Well here it is
« Reply #67 on: September 19, 2010, 07:14:50 PM »
Deadlines are made to be broken,

October sounds Good
air cooled, gt15 garret turbo with intercooler, 14x9" wheels with 225/40/14 toyos, front arb and disc brakes

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Condenser Coil
« Reply #68 on: September 20, 2010, 07:29:27 PM »
Question: has anyone experienced something similar?
Just previously tried 3 capacitators and still there were sparks at the points. Just put on a brand new one and I still get sparks  ??? No idea why, the points gap is set to 0.5. Even if the gap isn't correct there still shouldn't be any sparks at the points.
The car started and revved well, though i think i may have run the engine out of fuel as after running for a good few minutes it just stopped on idle and didn't want to start. The gauge needle is at 0 though i thought it can go under 0 a bit (reserve?). So i'll put some fuel into it and start it up again tomorrow....
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
A few pics
« Reply #69 on: October 24, 2010, 04:04:50 PM »
Managed a few shots off a digital camera. I will try to make some more in a more suitable environment soon  :)
Anyway, i was very pleased when it all came together finally. I had problems with the oil sump as it had a slight leak. Took it off and noticed there was two places where the sump wasn't straight (has a slight dent in it as well) so when installing with gasket paste i manged to break one of the sump bolts  >:( (turned out it wasn't a steel bolt either).Also had to refit the fuel pump with gasket maker too as the plastic spacer isn't straight. I still have a very very smal leak from the sump at two opposite corners. I'll just keep an eye out for oil consumption and fix it one day. Also noticed that the half axle rubber boot managed to pull out around 30kms before deciding to have a leak :P Looked under it the other day and no oil drip, so i'll change that it if it gets worse... (bought a new one in the meantime).
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: Well here it is
« Reply #70 on: October 24, 2010, 04:08:31 PM »
A few pics. The paint job didn't turn out too good on the doors. The middle is grayish and matt. Haven't tried polishing yet, but i had several attempts at the boot lid (which had it in a T shape) and it sort of came out (just now i can see the faint streaks i made with the polishing... :o) I'll be leaving till next spring as i can't be bothered doing it at the moment. I also manged to knock some paint off near the door pillar when fitting the doors... touched it up a bit but not as nice. All in all though i'm satisfied.
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: Well here it is
« Reply #71 on: October 24, 2010, 04:09:19 PM »
More..
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: Well here it is
« Reply #72 on: October 24, 2010, 04:23:07 PM »
The only problem i had at the MOT was with the brakes. The difference was only about 2% on each axle, just the machine showed that something wasn't true and didn't let it pass. They're brand new drums as well, so i thought it was strange. When testing on the first drive i noticed that the brake pedal pulsated slightly when braking, but thought it would wear away with use. So luckily they let me fix the problem and had it ready the next day. I took it to a turner to get them machined. He said two of the drums braking surface was a bit 'ripply' but surprised him it caused problems. I could feel the difference though when braking again: much smoother, pedal goes in slightly more now and still pulsates just slightly (handbrake also finally works now, 5 clicks and it stops the wheels dead :) ) Paperwork was a bit of a pain but got that sorted too. Only need a slight tweak on the carb to get a good CO at idle (high at the moment)...
Managed to get the steering mech. sorted, had to put it together twice as it leaked oil even with new gasket paper, so the extra gasket paste fixed that  :D
Just did a wheel alignment on it too as i just threw the front suspension together. No wonder i could hardly keep the car striaght. Had a toe of +3 deg on the front right and +1 deg on the front left  :P
Only the front right castor was a bit off (+6 deg instead of min. +8) but probably due to having new bushes. The rear toe worried me a bit as it was -19 minutes instead of +8 minutes on the left and -8 min on the right... i'll just keep an eye on the tyres as it handles well. The rear camber is  larger (+3 deg.)
Only have the roof lining to do... i'll try to get good shots of the car in a better environment:)
Well that's it from me at the moment, very happy and managed to also reach 105kmh the other day, had a approx. 45km trip today so very pleased  ;) **-
« Last Edit: October 24, 2010, 04:30:26 PM by GTMaster »
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

michaelodonnell500

  • Super Member
  • ***
  • Posts: 758
  • Karma: 7
Re: Well here it is
« Reply #73 on: October 24, 2010, 06:55:16 PM »
The paint job didn't turn out too good on the doors. The middle is grayish and matt.

I found my doors weren't too good on the 500 after the respray. I removed the doors and stood them upright to spray.I took the bonnet and boot off and laid flat, but they came up much better. I think its difficult to see how the paint has settled on the doors. Cars looking good, nice work!
Rust does not discriminate

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: Well here it is
« Reply #74 on: October 24, 2010, 09:21:11 PM »
Thanks! All the doors were removed and laid flat when spraying, the bonnet even got two coats :oops: The edges of the doors is fine (shiny) but the middle looks 'cloudy' ???
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...