The topic I will be documenting the work:)
I'll start with the engine
The idea evolved from early concepts. The reconstruction changed a lot of times - for example: adaptation of the head with 8 valves DOHC:

(once for sure I come back to this), the use of the head of the Fiat CC700 to 126p standard engine air-cooled, power supply with two carburetors and many other better or worse ideas. Certainly due to the fact that there were so many ideas , lessons and tests parts put together this together, I have gained a lot of experience .
In brief:
- 2x 34mm Mikuni carburetor (in this engine unnecessary)
http://www.odrdzewiacz.fora.pl/sport-z-epoki,8/traby-do-gaznikow,139.html- Adaptation of the head of CC700 ( head fr use - but with water-cooled cylinders )
http://www.odrdzewiacz.fora.pl/sport-z-epoki,8/glowica-cc700-do-fiata-126p,147.html-Oil catch tank ( useful )
http://www.odrdzewiacz.fora.pl/sport-z-epoki,8/zbiornik-odmy-mojego-pomyslu,141.html- Full flow oil filter + cooling ( useful )
http://www.odrdzewiacz.fora.pl/sport-z-epoki,8/przystawka-pelnoprzeplywowego-filtra-oleju-126p,149.html- Lightened flywheel ( useful )
At the moment is 4.4 kg , is likely to be less
http://www.odrdzewiacz.fora.pl/sport-z-epoki,8/odchudzanie-kola-zamachowego,145.html- Water pump DIY ( most likely replace it with an electric pump )
http://www.odrdzewiacz.fora.pl/sport-z-epoki,8/pompa-wody-diy-126p,151.htmlSo, it was shown how it was done. Later, quite by accident , I discovered that the engine block from the CC700 quite nicely fits into the gearbox ordinary Fiat 126p - when this block is VERTICAL .


This engine reminds me of something ...

I'm really liked it , because it looks very nice and retains the character of 126p - engine is the same engine (I mean BIS ) at 126p , only " drenched " another block - so for me it 's not even a swap, but something interesting

. From what I know , I am the first , which realizes this idea. Well, but the thing - I wanted to use the engine block of CC700 due to hydraulic valves, but I gave up the idea because this solution is not very suitable for sports applications , in addition, requires a number of improvements ( factory defect of these engines is just too soft " glasses " ).


BUT the BIS engine is haven't got hydraulic valves:). I was able to buy a brand new engine block. Head is from CC700 (bigger valves than BIS), and everything I put on a standard oil pan 126p without air duct.


Here 's probably a lot of people ask , but what about the water pump and oil (in BIS / CC they are located in the oil pan) . With certain adaptations , the timing of the cover fits into a standard Fiata126p BIS block , and thus fits the oil pump.

Valve cover is BIS- fit plug & play , of course, to the head of the CC , but in contrast to the CC is steel, so it can be welded to the elements of an ordinary 126p

because the engine will stand upright.




After sand blasting + already drilled base of the filter.



I started porting the head



The next thing - what I wore on the head it was " something of interest " to the engine. I do not like engines forced induction, but I considered the use of a turbocharger. But still, non- turbo is a little hard to tame, is much different phenomena and difficult issues , in addition there is something quite hard to choose. Did a little research and bought a supercharger, Eaton 24


Honestly, I chose size on the principle of an eye , and now I know that it will fit me perfectly! Even ( not tested by me) the direction of rotation is correct

. Well I'm glad! supercharger has always been my dream. I must design and make the whole intake, compressor and alternator mount - a lot of work .


It's nice that I have a tensioner!



I have prepared a model here:




And here we come to the point where I decided on the construction of the injection - ignition ( with the help of my brother, electronics) with the ability to control boost pressure .






I decided to apply the injection of a number of reasons - the most important is to gain experience and knowledge to a greater extent than would result from the traditional system. Another reason is the potential and accuracy of solution - injection, in particular, the MPI can very accurately control the motor and most importantly, to regulate its performance at a specified time (eg data speeds ).The engine very easy to destroy , and I want to have control over it and to learn, gradually improving its performance. Injection , in the initial phase of work and adaptation is complicated , but for example, later to change the settings I don't have to move ( mechanically ) in the system , and also I know a lot more. You can prepare different maps for different purposes , change them accurately and quickly. I want to get close to the limit of my knowledge and continue to learn .
My first attempt with the composite intake manifold - today I have an another idea ( technology )

This is a first model of the interior of the "positive" manifold - is wax.
View the lamination :

(it was a prototype , is now working on another )
That brings us to the current moment!
Sheet:



I'm working on a new intake manifold :





I also have an electrically operated relief valve ( by- pass) to the compressor ! New technology!

I finished the model of the manifold:






Now it looks:


Greetings!