Author Topic: BIS Overheating  (Read 7598 times)

0 Members and 1 Guest are viewing this topic.

1973/126

  • Super Member
  • ***
  • Posts: 1753
  • Karma: 23
  • Location: Tunbridge Wells
Re: BIS Overheating
« Reply #15 on: November 23, 2013, 09:10:43 AM »
 Ricambio used to the kits for the bis, but they don`t seem to sell them anymore.
 I think Pete126 has one of them installed on his car.
1972 Fiat 500
1980 Fiat 126

gammakeith

  • Super Member
  • ***
  • Posts: 137
  • Karma: 4
Re: BIS Overheating
« Reply #16 on: November 23, 2013, 09:40:09 AM »
I have that "raised thermostat" kit on my car as well.  However, at the end of the day, if the fan switch trips in too late its going to overheat (like mine).  I've just got the following;

http://www.ebay.co.uk/itm/390589750908?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649

I measured it as tripping in at 85 degrees on the first contacts and 90 degrees on the second contacts which strikes me as a little more sensible than the original (or the other ebay one I tried).  The actual switch has the same thread as the original so would screw straight into the rad but, alas, Googling the part number on the switch did not get any hits.

Two of these;

http://www.ebay.co.uk/itm/400292899718?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649

and one of these;

http://www.ebay.co.uk/itm/190836949737?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649

Plus some soldering should get it sorted quite nicely  :)

Keith


chrisrhodesinlbz

  • Subscribers
  • Member
  • ****
  • Posts: 69
  • Karma: 0
  • Location: Leighton Buzzard, Bedfordshire
Re: BIS Overheating
« Reply #17 on: November 24, 2013, 10:38:59 PM »
Thanks very much for your explanations and advice!! This Forum always comes up trumps.

I'll look in to getting that fix done!

Chris

gammakeith

  • Super Member
  • ***
  • Posts: 137
  • Karma: 4
Re: BIS Overheating
« Reply #18 on: November 25, 2013, 07:20:32 AM »
You might want to wait until my 'fix' is tried first!!  I might be reporting back that my fan is now running for 75% of the time and the car is running too cool  ;D 

Keith

gammakeith

  • Super Member
  • ***
  • Posts: 137
  • Karma: 4
Re: BIS Overheating
« Reply #19 on: December 01, 2013, 07:03:33 PM »
Well so far so good!  I spent a fair bit of yesterday rewiring so I'm now the only bits of the original fan wiring I am using are the two live feeds for the fan and idle solenoid.  Even then I had to bypass the two rusty connectors in the passenger footwell and cut back a fair way to find good copper to solder the repair sections in.  The original idle solenoid was also rusted solid internally but fortunately I had a spare that worked fine.  The two new earth relays and the shiny new resistor are now mounted to the left of the air-box.   I ended up just swapping the old fan switch for the new one as I was worried about over-cooling if I plumbed the new switch into the top hose as originally planned.  I think that was the right call as the fan kicks in on the low speed setting at about 1/3 of the way along the gauge.  Even though it was close to freezing outside my wife reported she had to turn the heating down as it was getting too hot on full.  The fan ran on for 10-20 sec after the ignition was turned off (spirited drive) so it looks like its about right to me!  I measured the low speed switch on the new fan switch as kicking in at 85 degrees which is approx 10-15 degrees lower than the specification for the original.

Looks like that's one job ticked off the list  ;D

Keith

Pete126

  • Administrator
  • Super Member
  • *****
  • Posts: 3369
  • Karma: 35
  • Location: West Yorkshire
Re: BIS Overheating
« Reply #20 on: December 01, 2013, 07:29:50 PM »
Good work Keith :thumbup
Pete.      il cavallo piccolo

Scarlettkitten

  • Super Member
  • ***
  • Posts: 105
  • Karma: 0
  • Location: Midlands, UK
Re: BIS Overheating
« Reply #21 on: December 01, 2013, 08:32:51 PM »
Nice one, I've got this to do on my BIS as someone has had a go and it doesn't look like the fan kicks in :( may take me a while as car electrics scare me :o
1990 126 BIS

gammakeith

  • Super Member
  • ***
  • Posts: 137
  • Karma: 4
Re: BIS Overheating
« Reply #22 on: December 02, 2013, 12:28:32 PM »
First checks are simple.  Disconnect the two connectors from the radiator switch (bottom far corner) and bridge the white (earth) and black pins to check low speed operation (if I remember the colours correct) then bridge the white and red pins to check high speed operation.  I suspect (like mine did) the high speed fan will run but not the low speed.  The low speed circuitry is much more complex as it relies on a relay at the front working and a good connection to the fan resistor.  You should also get the idle solenoid clicking when you activate the low speed circuit.  The fan takes a lot of current so connections must be good!!

Keith

Scarlettkitten

  • Super Member
  • ***
  • Posts: 105
  • Karma: 0
  • Location: Midlands, UK
Re: BIS Overheating
« Reply #23 on: December 02, 2013, 06:01:47 PM »
Yep you were right, hi works but not low, so I'm going to fit the same as you did I think :) Cheers for the help.
1990 126 BIS

gammakeith

  • Super Member
  • ***
  • Posts: 137
  • Karma: 4
Re: BIS Overheating
« Reply #24 on: December 03, 2013, 07:18:57 AM »
Does your fan relay click when your bridge white/black?  If so, its worth checking the connections to the low speed resistor at the bottom of the fan housing.  Its in an excellent position for getting blasted by road muck/salt etc.  My connections were in a bit of a state. Otherwise, it could be the relay itself.  I was it that position not long ago and finding corroded connections everywhere drove my decision to rewire the circuit.  While I was at it, it seemed sensible to put the extra relay for the high speed earth so I can use an alternative fan switch with lower trip-in.......

Keith

Scarlettkitten

  • Super Member
  • ***
  • Posts: 105
  • Karma: 0
  • Location: Midlands, UK
Re: BIS Overheating
« Reply #25 on: December 03, 2013, 03:13:04 PM »
No click when i bridge wht and blk, someone's had a bodge session in there, twisted wires and insulation tape everywhere, I'll just redo it and bin the hacked wiring I think, it's a real mess.
1990 126 BIS