Author Topic: Which mig welder gas or gas less  (Read 5510 times)

0 Members and 1 Guest are viewing this topic.

fixit

  • Super Member
  • ***
  • Posts: 169
  • Karma: 3
Which mig welder gas or gas less
« on: April 23, 2013, 11:37:30 PM »
 i'm struggling with deciding on a welder gas or gas less mig
I thought id cracked it, then read: mark the welder, classic car, and an article in landrover mag and a mig forum, and each give conflicting advice or far too much info which confuses further, ( I was a non mig  gas welder but don't have access to that kit
so taking into account of all info I seem to need a mig welder that can be
run off house mains,
a torch that not permanent live (has a switch action), not keen on electric shocks
 can weld body work,
has a wire speed selector switch and weld power setting
 it has to be able to be used outdoors in a windy garden, no protection from elements (I wont be using in wet weather)
and not suffer from wire bird nesting.
be reliable for this project.
will it be gas or gas less???

 so what do you fellow restorers use or recommend?
 
regards fixit

 

kev126

  • Super Member
  • ***
  • Posts: 473
  • Karma: 6
  • Built not bought
Re: Which mig welder gas or gas less
« Reply #1 on: April 24, 2013, 12:01:40 AM »
I guy I know who fully restores Minis uses a Sealey SuperMig 180. It's probably best to spend a little more money on a decent welder because the more expensive ones ARE better! And always gas. I think the non-gas arc welders are known to just be crap.
1989 Fiat 126 BIS

dajwid

  • Subscribers
  • Super Member
  • ****
  • Posts: 2932
  • Karma: 14
Re: Which mig welder gas or gas less
« Reply #2 on: April 24, 2013, 07:04:16 AM »
I am really new to this but I know this will open a real can of worms.

I have a very good arc welder, it does the job fine. For bodywork you really need a MIG it is easy to learn. Gas or gassless, you will get a better finish with gas, but for a couple of small diy jobs gassless will be OK.

Buy the best Mig you can afford, as all the articles say, as for Mig welding in the wind, all that happens is you won't have any sheilding gas and end up with a mess, but you could just put something up the sheild you from the wind.

I am sure plenty of more experienced people can give advise.

(this weekend I welded a repair section on my dash board with m trusty old Clarke 190 arc welder, it looks OK)

thepuddlejumper

  • Super Member
  • ***
  • Posts: 685
  • Karma: 2
  • Location: Scotland
Re: Which mig welder gas or gas less
« Reply #3 on: April 24, 2013, 12:53:45 PM »
Hi I use a 180 mig with gas, it has the option to go gas less but I don't fancy that.  If you weld outside you should use a screen to prevent anyone looking in and getting a flash, painful, also to keep the weld area shrouded in gas or it will just spatter and not weld.  To get the best results buy the best you can afford.  You will need to find a gas supplier if you intend to do a lot of welding as the larger bottles are much cheaper in the long run, the small bottles don't last a jot.  Hope this helps.

Ralph

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
Re: Which mig welder gas or gas less
« Reply #4 on: April 24, 2013, 05:32:33 PM »
I have just been looking into Mig welders myself but there are so many out there on the internet. I can't find any local suppliers to go & have a look & a chat. So recomendations are useful as I don't want to end up with some mickey mouse  item. I was thinking about a gasless model that uses the flux coated wire but I read one review that said you get a lot of splatter with these so it is hard to see exactly what is going on at the weld compared to the gas models. So reckon it will be gas at least.

wsmitwil

  • Super Member
  • ***
  • Posts: 371
  • Karma: 2
  • Location: South Shropshire
Re: Which mig welder gas or gas less
« Reply #5 on: April 24, 2013, 05:49:33 PM »

Don't get a gas less one I've got one and it's c*** very weak not really good enough for car work
fiats forever

kev126

  • Super Member
  • ***
  • Posts: 473
  • Karma: 6
  • Built not bought
Re: Which mig welder gas or gas less
« Reply #6 on: April 24, 2013, 06:03:49 PM »
So I think we've summed it up -

  • Always go for gas for a better, stronger weld
  • Don't skimp on the cost. You get what you pay for.

I've gotta get one now!
1989 Fiat 126 BIS

grubscrew

  • Super Member
  • ***
  • Posts: 244
  • Karma: 3
Re: Which mig welder gas or gas less
« Reply #7 on: April 24, 2013, 06:35:50 PM »
 Having been through the crap welders , I too can say gasless are not used in industry for obvious reasons, any way what you save on gas you pay for on special wire. They are only ok if you are using in windy conditions as there is no gas to get blown away.
   I use a MUREX Tradesmig 171, and is a brilliant bit of kit, with variable wire speed/thickness of metal and weld timer for spot welding, all together with a "Euromig" torch. Its on casters and takes the slightly larger bottle of Argon/Co2 mix, available from your local ADAMS Gas dealer. Although its best plugged into a 16amp socket (blue plug), you can run it on a 13 amp, as Ive never maxed it out.
  There are MUREX dealers through out the UK. Avoid the hobby welders, although ok for odd work from time to time, go one step up, its worth it. Mike.
All things Italian.

dajwid

  • Subscribers
  • Super Member
  • ****
  • Posts: 2932
  • Karma: 14
Re: Which mig welder gas or gas less
« Reply #8 on: April 24, 2013, 10:32:32 PM »
(I use a MUREX Tradesmig 171), I agree a great welder but sadly it costs as much as my 126 is worth  ;D


Tate

  • Super Member
  • ***
  • Posts: 211
  • Karma: 3
Re: Which mig welder gas or gas less
« Reply #9 on: April 25, 2013, 04:37:21 AM »
Go for a gas welder! Gas less welders are a joke if you are going to use the welder for cars. I wouldn't choose the cheapest because they are usually crap. A good welder will last for decades.


I use Migatronic Automig 180 and it is perfect!

Fiat 126 -73 project
2 x BMW E21

stuey

  • Subscribers
  • Super Member
  • ****
  • Posts: 1409
  • Karma: 14
  • Location: kings lynn
Re: Which mig welder gas or gas less
« Reply #10 on: April 25, 2013, 07:26:45 AM »
Agree pretty much with whats being said here- get a gassed mig welder (gasless wire is crap) I have a machine mart clarke 130 and Its served me well for 15 years now but if I have the choice I would at least make sure its got a euro torch (mine doesnt) and it has wheels (I had to buy a seperate cart for mine) and can support a big bottle (essential if you are doing a resto- nothing worse than running out of gas on a sunday afternoon!)
one resprayed and another arrives- double trouble BIS style!!

fixit

  • Super Member
  • ***
  • Posts: 169
  • Karma: 3
Re: Which mig welder gas or gas less
« Reply #11 on: April 27, 2013, 02:29:07 AM »
thank you all for your helpful advice  ;D sorry for delay in reply

 mig gas welder it will be

thought  narrowed the mig choice down to around max 185 - 200amps min 20amps - 30, to a Sealey, Murex, Migatronix, Clarke, Portamig or Oxford,  but then a spanner flew, and put me totally off course,

 migs are fairly easy to order online, unlike finding a good local gas and wire supplier, once I get me voice back, going to make some calls before making final choice then ordering
bah heck

my neighbours are sheep, quite nosey and are outstanding in their field, ;D
 I will make a fireproof screen before the local baaa sight authority looks me up. these ewes don't have pink coats.. unlike the ones in Scotland.

while gathering intel I came across this post, from Teflon the pictures could help fellow restorer welders..

http://www.lro.com/forum3/viewtopic.php?f=24&t=34568

 thank you again for help so far
regards f



Lloyd74

  • Super Member
  • ***
  • Posts: 128
  • Karma: 7
Re: Which mig welder gas or gas less
« Reply #12 on: April 29, 2013, 08:58:22 AM »
Iv'e got a clarke (Machine Mart) 150te turbo had it 6yrs GAS and with this ive restored a Rover P5 using about ? kilometers of wire? only had to replace the wire feed wheel in all that time, down to how much use and it gets used most days. Ive put roofs on cars and thousands of other things Ive got a stick inverter and a TIG as well all of which I use regularly.
Ensure you use a gas MIG as gassless are various expletives and for automotove applications run it on 0.6mm wire as the thin stuff is 1mm and it reduces the blow through hold the torch at 45 degrees to the seam to effectively increase the thickness of the metal use the lowest power setting required to give effective penetration and dont forget that wire feed speed will also effect the power as well as suit your speed. You can use Co2 but co2/argon Argoshield is LOADS better giving a tidy result, most little bottles don't last long so buy the 110ltr ones their more expensive but last loads longer. When the weld quality degrades it may be down to spatter in the torch shroud which must be kept clean as it must be insulated from the current and the build up of spatter inside it links the shroud to the electrode also the tips wear as the wire passes through so make sure you have spares as this causes bird poo welds. Always cut right back to good metal and always make a good earth connection!
Hope this helps! LLLLLLLOYD!

fixit

  • Super Member
  • ***
  • Posts: 169
  • Karma: 3
Re: Which mig welder gas or gas less
« Reply #13 on: May 22, 2013, 11:36:13 PM »
well
I finally went for a Clarke
the main reason was comsumable parts would be easy to locate
 and the cost, I joined the email club beginning of year, machine mart just sent me a vat free one use code which meant I could get a better welder for less money
I finally sourced gas around 25 miles away using the recommended www.adamsgas.co.uk locator although the sites locator wouldn't link to suppliers site, so ended up ringing
argon mixed co2 rent free bottle hobby gas, is £91.00 for the initial bottle inc gas
 then any refill swap is around £30 the bottle is about 75cm by 15cm
thank you all for your helpful advise  ;D
regards f

Lloyd74

  • Super Member
  • ***
  • Posts: 128
  • Karma: 7
Re: Which mig welder gas or gas less
« Reply #14 on: May 25, 2013, 10:09:46 PM »
I love welding, it's actually simple once you get through the myth just practice 1st on scraps and get used to your machine using a mig is the simplest way to achieve great results
Enjoy and message me if you get stuck!
LLLLLoyd