Author Topic: Speeds in gears?  (Read 1488 times)

0 Members and 1 Guest are viewing this topic.

fightingtorque

  • Super Member
  • ***
  • Posts: 120
  • Karma: 0
Speeds in gears?
« on: January 11, 2012, 12:47:54 AM »
Hello,

Been enjoying 126ing the last few days, generally it is running reasonably well although the main thing is to get on with the mark 2 fuel injection setup.

One thing, it doesn't seem so tractable at low engine speeds as i had remembered, maybe this is something that I lost a bit when I raised the compression ratio.  I remember when I first got the car I was really surprised at how torquey the engine was consider its small size.   

It isn't so much that I now feel a lack of torque, I think it is better than before, but the minimum speed at which it will pull comfortably seems quite high.  I know the gearing is quite long considering its a small engine and only 4 speeds, but it doesn't really pull smoothly below about 35mph in 4th gear for example.  Is this also true of the standard car?  (BIS).

I have 145/70 tyres on, so that does mean it is a little geared up over standard.

I am still using the original distributor ignition at the moment.  With the mark 2 fuel injection I will get fully mappable ignition across speed/load table.

Gav

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: Speeds in gears?
« Reply #1 on: January 11, 2012, 12:13:38 PM »
The old speedometers had red dots next to the speeds where it was ideal to change gears (or near red line, don't know). 2nd at 30km/h, 3rd at 50km/h and 4th at 80km/h.  I found that it cruised comfortably in 4th at 50km/h (though not much acceleration if you floored it but it did pull nicely).
I actually found the gearing to be short, I think the diff. ratio is around 4.0 or 4.1:1 and my service manual showed the ratio of each gear to be low (even 4th is around 1.1 or 1.2:1), a longer 4th gear or a 5th gear (maybe even a different diff. ratio) could have given a slightly higher top speed and would have made cruising at or a bit above 100km/h more comfortable for long distances in my opinion.
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

DEYAN IYI

  • Super Member
  • ***
  • Posts: 418
  • Karma: 2
    • Bulgarian Polski FIAT 126p Fanclub
  • Location: Plovdiv/Bulgaria
Re: Speeds in gears?
« Reply #2 on: January 11, 2012, 03:53:33 PM »
With standard 135/70 R13 the Bis on highest torque on 2000rpm goes with 52km/h or 32mph. So must be really happy on that speed.

I don't know for the Bis, but according to the instructions for the aircooled one the lowest cruising speed is about 2000rpm on each gear or 12-19-30-45km/h. On 3000rpm (highest torque) is 18-31-41-66km/h. And max speed 30-50-80km/h that is about 5300-5600rpm when shifting. Not recommended to run for long time over 5000rpm. Max speed on IV is 105km/h on 4800rpm.

126's IV gear is real V gear being overdrive of 0.871; with the Bis's final drive 9/39 (8/39 for the aircooled) is just perfect, but needs on the place of III (1.3) one shorter and one longer like in the Abarth options III - 1,421; IV - 1,091) :) The good thing is that is something easy to buy, except the price. 8)

PS - lower than 2000rpm isn't good for the cooling of the AC.

DEYAN IYI

  • Super Member
  • ***
  • Posts: 418
  • Karma: 2
    • Bulgarian Polski FIAT 126p Fanclub
  • Location: Plovdiv/Bulgaria
Re: Speeds in gears?
« Reply #3 on: January 11, 2012, 06:48:49 PM »
 :)

So, you can shift gears on 5000rpm. Top speed 116km/h at 4500rpm where the max power is.

« Last Edit: January 11, 2012, 06:56:13 PM by DEYAN IYI »

fightingtorque

  • Super Member
  • ***
  • Posts: 120
  • Karma: 0
Re: Speeds in gears?
« Reply #4 on: January 11, 2012, 11:35:36 PM »
Good info.

So if 2000rpm in BIS is 32 mph, I guess it probably isn't too surprising that the minimum speed i find it happy at is about 32-35mph. 

I think I have been spoiled by these modern engines which can run down to low revs (more cylinders, multipoint injection etc) - my Cinq will happily totter along at 1500rpm in 5th and I have an alfa 156 V6 which will take 6th gear at 30mph with about 1200rpm.

But with only 2 cylinders, single point injection and currently only conventional distributor ignition, you cant expect the same thing.

I had to go on a speed awareness course recently, the guy was telling people his simple rule of 2nd gear for 20mph limits, 3rd for 30.  He believed too high a gear will hurt the fuel consumption.  We started to get into a debate about cylinder pressure, engine friction, fuel injection, variable cam timing etc. but i dedided we would be there all night and let him get on with it.....................