Author Topic: special cranks  (Read 3660 times)

0 Members and 1 Guest are viewing this topic.

smallcox

  • Super Member
  • ***
  • Posts: 433
  • Karma: 4
special cranks
« on: September 14, 2010, 07:51:30 PM »

Hi everyone,
With winter now on it's way (and thanks to Pete126) I was looking at upgrading the standard crankshaft. At presant i have many idears running through my head and depends on cost etc wondered if anyone has had the fun off playing with modified cranks, you now the ones good for 8000rpm and don't break. [-/

Also has anybody bought upgraded bearings? do they last on a road car and who supplies them?

Thanks again Smallcox
air cooled, gt15 garret turbo with intercooler, 14x9" wheels with 225/40/14 toyos, front arb and disc brakes

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: special cranks
« Reply #1 on: September 14, 2010, 11:59:59 PM »
Hi Steve, I've been reserching this subject for a while now, there are no clear descriptions on the subject, as on here, everyone seems to go along different directions.
Rusty tells me the 500 website is like watching paint dry, so doubt there will be much wisdom from there, hence my dragging my feet with membership there.
From my research I have found the high performance engines used in the famous Abarth 595's could do a higher speed than the new Fiat 500 Abarth. I know, sounds like a load of old poo AGAIN from me but I think it was 125mph top speed for the old 595, and the new Abarth is quoted at 120mph...this is I think...not gospel truth as I have a memory like my 500's floor's ability to hold water. I do remember it was 5mph faster...with drum brakes!
Cranks were upgraded to a steel crank, no mention I have read anywhere specifies different bearings but roller bearings make sense in my opinion, how that is going to affect lubrication, you're cleverer than me so you'd probably be better able to answer that. The next must seems to be stronger conrods, I have seen Titanium rods!!! for a price...
They also fit lightened pistons and often drop one ring, less friction? seems a bit too racy for my every day wagon.
Lightened flywheel, some which look like a work of art, and much stronger famously red Abarth valve springs with obviously offset valve guides and bigger valves, bigger capacities up to 800cc with reinvocement plates fitted under the barrels. Apparently the 650 engine was reinforced with webs in the casting of the crankcase. Obviously cam is changed.
Webber 40 carb seems a popular choice on the higher spec cars. 1 to 1 ratio on the fan, higher compression ratio..it goes-on! Alot of Euros can be spent i remember something like 1600 euros for titanium rods! Even Titanium valve caps!

I'd love to find-out the exact spec of the old very fast 595's as it's give us a clear direction to go in as they've been there, done that, broken bits. I'll find the website tomorrow, I saved it for the steel crank.
They aren't cheap, but then you're serious about your car, I want one [-/
With the possibility of over 100mph from an air cooled, it's the reason I moved from BIS to air cooled! Might take me 10 years but I'll get there :oops:
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

thepuddlejumper

  • Super Member
  • ***
  • Posts: 685
  • Karma: 2
  • Location: Scotland
Re: special cranks
« Reply #2 on: September 15, 2010, 01:01:23 AM »
I thought I read somewhere that the crank from a 700cc Cinquecento, water cooled 170A.000 engine is an option.  Only thing it was only available in main land europe.

Ralph

hudsonhenry

  • Super Member
  • ***
  • Posts: 303
  • Karma: 1
    • http://www.retro500.com
Re: special cranks
« Reply #3 on: September 15, 2010, 10:03:09 AM »
Not sure if it helps much, but I started to look at forged steel crank's and rods but decided that the cost in relation to the actual possible power gain, once you rethink the cam, head, carbs and exhaust to properly exploit the extra revs that these would enable was too high. The Giannini 650NP's used a forged crank and Ferrari Dino con rods, the full on, rebuild every season race engines are putting out a maximum of around 70bhp but would be totally impractical on the road. I came to the conclusion that it would be much cheaper fitting a bigger 4 cylinder water cooled engine.

I have a copy of the original Abarth user manual which states the top speed for the 595ss as 130kmh (80.78mph) and the 695ss as 140kmh (86.99mph). With an Abarth 5 speed gearbox the 595 will do 21Km/h per 1000 rpm and the 695 22.2 Kmh per 1000 rpm for the 695. You would need to rev a 595 engine to 7,600rpm to get to 100MPH and 7,251rpm in the 695. I'm not sure which diff the Abarths used, the 126 BIS diff is the one to use to get more top end.

I also had a look at the gear kits available for the 500/126 box and, even with the five speed conversions the ratios don't get much higher than standard, I guess because the kind of racing they still do in 500's is short circuit stuff or hill climb where acceleration is more important than top end.

Nigel


http://www.retro500.com the site dedicated to modified Fiat 500's

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: special cranks
« Reply #4 on: September 15, 2010, 10:22:51 AM »
Ok must have been poo I read somewhere....

I see 75 to 80 fairly regularly in my fairly standard 650 so Abarth performance parts will do diddly squat :oops:
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
Re: special cranks
« Reply #5 on: September 15, 2010, 11:22:11 AM »
Now then , this could be a story with a tragic end  :oops:
Some of you will remember that I got an Abarth 595 original unused camshaft a while back which a guy had put on eBay. In my subsequent e-mail conversation with him he told me that he used to race an Abarth 595 in the sixties. He also told me that he was having to clear out a storeage unit in July this year. Preserved in that unit there was one of his old race engines . He mentioned Nanni heads , carb and a roller bearing crankshaft . He said that the engine would rev to 10,000 rpm  ::)
So if you feed that into some of Nigel's ratios you get some pretty scarey figures.
I kept in touch with the guy with a couple of e-mails which he answered then the july deadline passed & the last two e-mails he did not reply to.
He had told me that his wife hated all this "old junk" & he was under pressure to get rid of it.
So I can't help wondering what happened , I know that he did not eBay the engine or any more bits But I would hate to think that it went into a skip  :o

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: special cranks
« Reply #6 on: September 15, 2010, 12:20:02 PM »
http://www.synlube.com/racing.htm

800cc advertised here saying 170km/h possible? http://www.scorpioneabarthparts.nl/Mercato.htm

Like I say, confusion as to what was done, what is possible, and what will be a completely unreliable beast...

But I admit the standard Abarths that were sold were not overly fast, perhaps the legend is not as impressive  :P
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

hudsonhenry

  • Super Member
  • ***
  • Posts: 303
  • Karma: 1
    • http://www.retro500.com
Re: special cranks
« Reply #7 on: September 15, 2010, 01:07:41 PM »
Ok must have been poo I read somewhere....

I see 75 to 80 fairly regularly in my fairly standard 650 so Abarth performance parts will do diddly squat :oops:

75 to 80! that sounds quite fast for a standard 650 engine. You will be doing between 5500 - 6000 rpm to get to that speed, which is 1000 to 1500 revs over a standard engine at peak power (24bhp at 4500rpm). Are you reading the speed off the original Fiat speedo or calculating your top speed is via a rev counter , wheel size, top gear ratio and diff ratio. Also are you running standard tire sizes as any increase or decrease in rolling radius will affect your speedo reading.

6000 - 6500rpm is about the maximum a standard but balanced crank will take with any reliability. I have seen several that have been snapped by over revving.

Non of the original Abarth 500's put out big power by modern standards but back in the day the 38bhp of a 695cc was quite a result. I think I'm correct in saying that the original 998cc Mini Cooper only had 55bhp when released.
http://www.retro500.com the site dedicated to modified Fiat 500's

Eklipze3k

  • Super Member
  • ***
  • Posts: 632
  • Karma: 2
Re: special cranks
« Reply #8 on: September 15, 2010, 01:31:56 PM »
80mph?? Best I ever managed (according to sat-nav) was about 74mph, which was on a long downhill stretch of the A9 last year. I think that may have been around about when the head started to eat the manifold bolt threads though :oops:

smallcox

  • Super Member
  • ***
  • Posts: 433
  • Karma: 4
Re: special cranks
« Reply #9 on: September 15, 2010, 02:57:54 PM »
Hi gang,

Just before I start a war on this subject :cry: I hear what you guys are saying. Before I started moding the engine back in the very early 90's I found if you can get that speedo past 72mph on a flat then you were doing well, slight upgrade in road and speed quickly dropped to 60mph, I quess you now what i'am saying.....BUT. many years on I don't think I can safely get 125mph (sorry Darrel but Urban legends) the power in standard does peak at 4500 and this is why 70mph hits a wall in top gear.
I found now that the engine I run has past the point that the crank will stay in one peice. Pete126 explained the use off roller bearings on the rear journal but I would prefer to used plain bearings as this is a road car that I intend to use and engine hardsness must be considered. Shame about that garage full off parts Rusty

At present the engine is complete and I only want to strenghen the crank and bearings for relieblity reasons. Money is tight so no open cheque book on this project. possibly a steel billet made to my own spec but require more info on what does work because what I have seen seems very dated >:(

Thanks again for all your input and be back soon [-/

Smallcox

Ps Darrell if you fit a Bis gearbox and get your engine revs to 6000rpm then this is as good as 100mph, see why I need a 5th gear, also took a look at that site with 800cc engine might do 170kph? thats 105mph :oops: Don't always believe what the seller tells you
« Last Edit: September 15, 2010, 03:32:09 PM by smallcox »
air cooled, gt15 garret turbo with intercooler, 14x9" wheels with 225/40/14 toyos, front arb and disc brakes

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: special cranks
« Reply #10 on: September 15, 2010, 03:49:47 PM »
I have to confess to having a BIS diff and box. I get an annoying wheel wobble between 60 and 65  hence good intentions of sitting at 60 soon fade, concerntration then goes to making sure no numpty slows me down too much for the next hill :oops:  70 is 68 on the satnav if that helps.

I only realised I had a BIS diff after remembering that when I got the car, the first was knackered, I then got a box which I made the mistake of first before completely stopping. Mick had given me a BIS box which I simply put the bell-housing onto, I didnt think there was a difference at the time :o

Yes maybe it is being over reved a bit. It has read 80 on the speedo once of twice :oops:

I guess my welly boot needs lightening.

I like you thoughts there Steve, there is alot of dated thinking out there.My 600 bike puts-out 105 bhp and is as reliable as a wood stove! Ok so it's a 4 cyl and dohc 4 valve etc etc with little torque, but I was on a little sv650 suzuki the other day and had loads of fun with it as torque is good on that twin, front wheel gets very light  :oops:

Hey Steve ask if the price of a crank goes down for two :)
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

smallcox

  • Super Member
  • ***
  • Posts: 433
  • Karma: 4
Re: special cranks
« Reply #11 on: September 15, 2010, 04:28:35 PM »

Hey Steve ask if the price of a crank goes down for two :)
[/quote]

Will do Darrell, but it still wont be cheap :cry:

Reading the above from you guys can see a lot off thought on the subject.

It's true most gearbox convertions do lower the ratio's this is too help with the short power bands the racier cam produce. Been there and now run a turbo so loads off torque and as mentioned before I run a bis gearbox and still run out off revs and on the motorway 70mph is 4000rpm and feels like I should be changing into another gear, so a 5th gear converstions on the way [-/

Smallcox
« Last Edit: September 15, 2010, 04:31:28 PM by smallcox »
air cooled, gt15 garret turbo with intercooler, 14x9" wheels with 225/40/14 toyos, front arb and disc brakes

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: special cranks
« Reply #12 on: September 15, 2010, 05:16:29 PM »
 ;) nothing is cheap when worshiping the god of speed :) Perhaps some of the others will be coming to this church? ;D

Down here it's more important to be able to sit at higher speed as there isn't that many slow roads I travel on. It'd be nice not to constantly see someone in the mirror not trying to push me along faster...I can stop quick now thanks to Rusty :) which often catches them out.

I agree with the 5th gear being a must, I get to the stage where I wonder if I will be visited by a conrod in the car :oops:
Theres a great downhill section on the M3 where she normally does her high speed trick, the 5th gear would make it better ;)

With the new 500 on the interweb, it's making finding the bit I read about the Abarth being so fast a nightmare.
I want to find it and tell them they talk poo!!!! :P
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

Pete126

  • Administrator
  • Super Member
  • *****
  • Posts: 3369
  • Karma: 35
  • Location: West Yorkshire
Re: special cranks
« Reply #13 on: September 15, 2010, 08:45:18 PM »
As Lad. (1973/126) mentioned there are quite a few modified 126's in Poland that are using the Skoda 120/130/ Rapid Coupe (1987-1990) 5 speed gearboxes on the fiat 1108/1200 engine transplants If its possible to make an adapter plate for them I'm sure its possible to make one for the 126 air-cooled engine, The only info i've managed to find is the final drive ratio is 4.1 and the gearbox is good for 80BHP at the wheels  :D
Pete.      il cavallo piccolo

smallcox

  • Super Member
  • ***
  • Posts: 433
  • Karma: 4
Re: special cranks
« Reply #14 on: October 31, 2010, 10:49:54 PM »
I like the idear off the stronger rapid gearbox but don't like the word it's heaverierererer. :-X

the 5th gear conversion is the way to go and after looking at Jans uk car the box can take more than i gave it credit for.

Now the crank is in designer mode with much research behind the curtains. the curtains being my favourite colour pink. ;D

so just got to pay for it now, and nobody must tell the wife because she just don't understand BHP and fun. **-

0-60 we will have to see
air cooled, gt15 garret turbo with intercooler, 14x9" wheels with 225/40/14 toyos, front arb and disc brakes