Author Topic: And So It Begins :-)  (Read 11333 times)

0 Members and 1 Guest are viewing this topic.

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
And So It Begins :-)
« on: June 26, 2010, 02:55:24 PM »
Various projects are moving along slowly but my 500L daily runner has been a bit off colour plus I wanted to try a minor upgrade on a standard 499ccs engine. Plan is to fit 126 camshaft , carb and exhaust along with the ported 500 head with enlarged inlet valves that I have just had done. Hopefully modest mods & an engine that breaths a little better.
I thought that the poor running may have been down to a blown head gasket or a valve but no evidence of that. Also engine has a real rattle so timing chain was suspect. This car has now done just over 100,000 miles so you are not sure what you will find  :oops:
Took a picture to show the sag on the timing chain but it did not seem too bad , compared it with 2 other used ones & they looked very similar. Will dig out a new one later to compare.
The Haynes Manual says that removal of the cam is best done with the engine out as the followers can drop. So just lifted the followers and pushed a bag tie through the holes in the follower , can't drop now  ;D
More to come  [-/

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: And So It Begins :-)
« Reply #1 on: June 26, 2010, 10:51:07 PM »
Thats a might fine looking big timing chain sprocket on there Rusty ;)

Never seen a lightened one like that before
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
Re: And So It Begins :-)
« Reply #2 on: June 27, 2010, 06:37:51 AM »
Finished the stripping now , found one minor & one major fault. Firstly the little petrol drain tube (not fitted on 126) had dropped out of the carb drip tray so may have been drawing a little more air there. The other thing was one of the inlet lobes on the camshsft had worn down badly & was a full 2mms lower & just over 4mms os cam lift. Also considering that the engine had a major rebuild by a well known Fiat 500 specialist about 25,000 kms ago I was very surprised to see the worst build up of sludge in the centrifugal oil filter that I have ever seen. Almost built up to the outer edge of the oil flinger behind the big pulley nut  :oops:
Now that camshaft sprocket. I only realised it was different when I dug out the others I had which are cast iron. This one looks as if it may have been machined from solid , weighs 215 grams as opposed to the 315 gram cast ones. No idea how it ended up in my standard 500L engine  ::)

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
Re: And So It Begins :-)
« Reply #3 on: June 28, 2010, 09:27:03 PM »
Started the assembly today , 126 cam in , timing chain on then checked out the oil pump which is quite an experience to get it apart & back together . Almost screwed up refitting the timing chain cover . PIcture of the pile of poo that came out of the oil filter , weighed in at 120 grams plus the tool that Haynes dared not show ! How to re-torque the crankshaft pulley nut  :oops:

bis13

  • Super Member
  • ***
  • Posts: 2749
  • Karma: 39
Re: And So It Begins :-)
« Reply #4 on: June 28, 2010, 10:28:00 PM »
ha ha so you found that fun too! its special tool no1! did you have a bit of bother with the timing chain etc? i know you are an old hand but i hope you have replaced all the sprockets along with the chain if you have changed it?
with regards to the worn lobe what inlet was it on as mine wore down and wondered if its the same lobe?

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: And So It Begins :-)
« Reply #5 on: June 28, 2010, 11:04:26 PM »
I thought about that Mick when I saw your cam had worn one lobe down.

The cam from what I understand relies on oil coming from the head, down the tubes into the cups, through the cup holes and onto the cam.

I thought maybe one of the tubes could be sticking-up into the head too far thus not allowing any oil to flow down or perhaps the casting channels the oil to all but one.

Perhaps the angle of the engine affects this as I've noticed mine sits a bit up at the back (pulley side)

My cam will be coming out soon so will do an inspection too.
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
Re: And So It Begins :-)
« Reply #6 on: June 29, 2010, 03:51:06 PM »
The inlet cam lobe that had gone was on the no 2 cylinder. No indications as to any cause for oil starvation but two cam followers were pitted on the face  & two of the steel cups at the top of the push rods were slighly loose. All replaced by good used components. Made more studs to fit the exhaust elbows to the head so as to avoid stripped threads from bolts. Fitted exhaust elbows and picked out a head gasket which turned out to be 0.015" thinner than the one that came off so minor compression rise there.
So now you are "torqueing" & head etc fitted  [-/
Still lots to do but getting there.

Allan

  • Super Member
  • ***
  • Posts: 226
  • Karma: 1
Re: And So It Begins :-)
« Reply #7 on: June 29, 2010, 09:18:02 PM »
Hope you set the tappets before you put the rocker cover on. One thing I used to do after a job like that was to get everything else done including the tappets and leaving the cover off start the engine briefly (as soon as it fires one small rev and then turn off) then recheck the clearances. What are the pins in the gasket for?
Allan

bis13

  • Super Member
  • ***
  • Posts: 2749
  • Karma: 39
Re: And So It Begins :-)
« Reply #8 on: June 29, 2010, 09:38:44 PM »
thats a form of accupuncture for perfect gasket alignment....

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
Re: And So It Begins :-)
« Reply #9 on: June 29, 2010, 09:59:22 PM »
 :D yes provisionary set the tappets for the first run bearing in mind the parts that I have replaced that will bed in ( I hope )  ::)
Now I delibrerately did not mention those pins , I thought that eagle eyed Darrell would have been straight on it , Allan you beat him to it  [-/
The thing is I think that a lot of the oil leaks come from a poorly fitted rocker box gasket and the gaskets do tend to bow in along that straight edge above the thermostat housing. So I had the idea of putt ;)ing in those two pins to align the gasket & it seemed to work fine

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: And So It Begins :-)
« Reply #10 on: June 29, 2010, 10:09:43 PM »
Eagle eyes was out riding motorbikes  :oops:

Had a go on an old '84 Suzuki Katana and an Suzuki SV....got a head full of adrenaline after having a go on that SV....front gets mighty light under acceloration  :oops: :oops:

I had a similar problem so I contact adhesive-ed the gasket to the rocker cover. A light coating of grease on the other side means it comes-off easily and goes back on easily.

Rumour has it from an old school mechanic I hung around in my youth observing work on old brit bikes, that grease was commonly used between gaskets.

I have to confess to the use of silicone on the carb inlet as I wanted that to seal like a ducks... [-/
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: And So It Begins :-)
« Reply #11 on: June 29, 2010, 10:14:57 PM »
Looking good  [-/ How much more power can be expected? Another good way to tighten crankshaft pulley nuts/bolts is either with an air wrench  :) or if you have a helper and the engine's connected to the gearbox then by putting it into gear and having the brake pedal pressed (or if you have a good handbrake then that may be enough).
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
Re: And So It Begins :-)
« Reply #12 on: June 30, 2010, 08:24:04 AM »
The guy who did the work on the head reckoned the porting would give an additional 2.5 to 3 hp per cylinder which would be a huge rise for a little 500. Then of course I had inlet port enlaged to suit a 126 carb, enlarged inlet valves fitted and the 126 cam so it is all a bit of an unknown  ::)

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
Re: And So It Begins :-)
« Reply #13 on: June 30, 2010, 08:19:34 PM »
So I got a little bit crazy & a bit impatient today, played with the exhaust & wanted to fire the thing up asap  :oops:
So I took the angle grinder & welder to the standard 126 exhaust for a posey tailpipe then pressed on with the re-assembly . Had to make longer studs for the exhaust brackets plus one for the 126 carb. Had forgotten that the rocker side stud is longer on a 126. Was going to rebuild a 126 carb but spotted a clean looking one in my garage & went for it (do a rebuild later , honest  :oops:)
Tried firing it up but no joy but I wanted to get the oil pumped round anyway. I had tried to be clever by just lifting the distributor off the old cam then dropping it down on the new but it was not right so after a quick rejiggle we had ignition  :D
Interesting as the engine is only supported by a large block of wood with a smaller block on top . All OK on tickover , quite a bit of vibration with more gas & on the over run but after about 30 mins of running to let things bed in oil circulate & get up to temperature I tried a good dab of throttle and sounds promising. Engine support / lower panel going back on in the morn then a road test  [-/

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: And So It Begins :-)
« Reply #14 on: June 30, 2010, 08:44:25 PM »
Rusty I tried doing that with my original exhaust, it looked and sounded good but kept on cracking, it needed to be well braced.

Just thought I'd tell you while you havn't got too much bolted-on to do anything :oops:

If you dig into the standard 126 pipe there is a baffle just behind where you welded-on your new tailpipe. Did you take tha baffle out?
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)