Author Topic: Engine mount bolt knackered!  (Read 4476 times)

0 Members and 1 Guest are viewing this topic.

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
Re: Engine mount bolt knackered!
« Reply #15 on: January 20, 2010, 04:11:58 PM »
So whilst tripping over an aircooled engine in my garage this morning I looked down on the mount. There is a baseplate that fixes to the crankcase with two bolts and that bolt goes into a deep screwed boss that is fixed to the underside of that plate. So if the Bis is the same why not replace the plate and get everything back to standard  ???
Not sure what "widened the grooves of the bolt" means but if the threaded section has been stretched then it has been subjected to extreme tensile stress which I doubt on a bolt that size and in that application. From the photo the bolt does not look stretched as it would also have "necked in" or reduced in diameter at the point of max stress. For the bolt to be damaged it would either have worked loose or have been subjected to additional bending stress due to a side load in any direction , probably the cause of Darrell's bolt failure. Side loads on the bolt could be caused by front or rear impact on the car or worn / busted mounts at the gearbox end  [-/

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: Engine mount bolt knackered!
« Reply #16 on: January 20, 2010, 04:27:06 PM »
I know why my bolt broke :oops:

Sodding speed bumps...I kinda lost it with them as the one road is about 4 miles long with them and just floored it, well sort-of  :oops:

So looking to do the 'bump stop' in the mounting trick the guys did here :oops:

Shhh don't tell the wife....I was late to collect her from work when it happened...

I promise I won't do it again sir :oops:
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

ciaoflyer

  • Super Member
  • ***
  • Posts: 1325
  • Karma: 3
Re: Engine mount bolt knackered!
« Reply #17 on: January 20, 2010, 05:15:03 PM »
My gearbox mounts were shagged!  Rusty do you think the bolt I am fitting will be ok?  Also brakes arrive and look good - Cheers! [-/

The Bis has a plate sticking out the back of the engine, icould change this but where do I get one?  Did have one on my old knackered engine but the 'travellers' pinched it off my drive along with a spare exhaust!

Other option is to remove old nut on bracket and weld a new one on...
« Last Edit: February 20, 2010, 10:29:21 AM by ciaoflyer »
Ciao4Now

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
Re: Engine mount bolt knackered!
« Reply #18 on: January 21, 2010, 12:31:40 PM »
OK so it is a different bracket on the Bis, someone must have a spare kicking around. I guess that those gearbox mounts compounded the problem of probably a loose bolt. But in the meantime I would get that bracket off to assess its condition. Possibly run a suitable tap through to chase out & check what thread is left. You may get away with a longer bolt backed up by a lock nut. If the threads are totaly stripped & your gearbox mounts are fixed I think your bolt will be fine. Have fun with the brakes  [-/

ciaoflyer

  • Super Member
  • ***
  • Posts: 1325
  • Karma: 3
Re: Engine mount bolt knackered!
« Reply #19 on: January 23, 2010, 12:51:46 PM »
Fitted!  It seems to work, all tightened up, ran engine and all seems fine.  The test will be when I take it for a run! :D
Ciao4Now

ciaoflyer

  • Super Member
  • ***
  • Posts: 1325
  • Karma: 3
Re: Engine mount bolt knackered!
« Reply #20 on: January 24, 2010, 09:59:23 AM »
Here's the knackered bracket before drilling through....

Ciao4Now

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: Engine mount bolt knackered!
« Reply #21 on: January 26, 2010, 10:13:00 AM »
Nice thread  :oops:
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)