Author Topic: Engine mount bolt knackered!  (Read 4477 times)

0 Members and 1 Guest are viewing this topic.

ciaoflyer

  • Super Member
  • ***
  • Posts: 1325
  • Karma: 3
Engine mount bolt knackered!
« on: January 17, 2010, 05:37:31 PM »
Here's one for you.

 I was replacing the rear engine mount with a new one, removed it fine but noticed that the bolt's thread was a bit dodgy. ::)

Sure enough refitted it and the thread went >:(  Now my engine has no rear mount!

What would be the best remedy for this?
Ciao4Now

ciaoflyer

  • Super Member
  • ***
  • Posts: 1325
  • Karma: 3
Re: Engine mount bolt knackered!
« Reply #1 on: January 17, 2010, 08:31:04 PM »
The offending item......



Could I get a slightly narrower, longer nut and bolt and thread it through the mount, through the old nut and then tighten it up?
Ciao4Now

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: Engine mount bolt knackered!
« Reply #2 on: January 17, 2010, 08:57:50 PM »
I'd say try and find one at the breakers. These are special bolts (length and thread i think) so it'd be hard to find a new one (unless you buy from places like Axel Gerstl etc.) I tried to find bolts to the door lock mount at a tool shop (on the b pillar) but couldn't get any....
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

ciaoflyer

  • Super Member
  • ***
  • Posts: 1325
  • Karma: 3
Re: Engine mount bolt knackered!
« Reply #3 on: January 17, 2010, 09:06:37 PM »
Do you think the nut will be knackered also?
Ciao4Now

bobblehead

  • Super Member
  • ***
  • Posts: 224
  • Karma: 1
  • monkeys on the move ..
    • my fiAT 126 PICK UP
Re: Engine mount bolt knackered!
« Reply #4 on: January 17, 2010, 10:31:31 PM »
a bolt is a bolt, the thread on the engine mount dont matter, aslong as other bolt is roughly same length or longer reckon you be ok, also thickness dont really matter as you could add a washer or 2

its a engine mount afterall

no doubt i will get slated for saying this but its my opinion

if i have asked for help .thanks in advance for helping and giving me advice .. all the very best to you all .. respeck monkeymoves .......

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: Engine mount bolt knackered!
« Reply #5 on: January 18, 2010, 04:42:12 PM »
If you're lucky then the nut is fine...
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
Re: Engine mount bolt knackered!
« Reply #6 on: January 18, 2010, 05:42:34 PM »
Oye Mate , I think you're nut might be knackered  :o
How can you even think about using a smaller size bolt to hold your engine in  :oops:
Not Like it is a sidelight or something.
I do not have a 126 rear mount now but I think that from memory the bolt would go into a semi-captive nut which is probably a special but replaceable so do not panic.
Nice photo by the way  ;)

ciaoflyer

  • Super Member
  • ***
  • Posts: 1325
  • Karma: 3
Re: Engine mount bolt knackered!
« Reply #7 on: January 18, 2010, 07:48:20 PM »
Managed to get a replacement nut and bolt but a bit longer, if the nut is done in I shall drill it through and use the new bolt.

If the nut is still usable I have managed to get an identical bolt aswell so I shall use that!

Ciao4Now

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: Engine mount bolt knackered!
« Reply #8 on: January 18, 2010, 09:11:08 PM »
My bolt like that snapped...spectacular noises resulted...

It it the same length and thread as that which holds the bell housing to the gearbox.

to be sure to be sure I have found a suitable nut which I believe to be a metric fine thread which was in a box of old Yamaha bits I have to act as a locking mechanism and a 'to be sure' if the thread was damaged.
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

ciaoflyer

  • Super Member
  • ***
  • Posts: 1325
  • Karma: 3
Re: Engine mount bolt knackered!
« Reply #9 on: January 19, 2010, 05:57:19 PM »
Here's the old bolt and the new bolt





new bolt is 10mm, slightly longer to pass through the old nut and then tighten up, also a sping washer and nyloc nut will be fitted to make sure it does not shake loose!

In ref to the original nut, our head technician at work says that the bolt has not been stripped but has at some point been loose and because of this the shaking of the engine has widened the grooves of the bolt and ruined it.  Also the original bolt has a 1.25 pitch thread and, according to him, can support up to 4.5tonnes! :o
Ciao4Now

bobblehead

  • Super Member
  • ***
  • Posts: 224
  • Karma: 1
  • monkeys on the move ..
    • my fiAT 126 PICK UP
Re: Engine mount bolt knackered!
« Reply #10 on: January 19, 2010, 06:01:23 PM »
spot on , let me know hoe you get on, as i removed a ford courier towbar today and its got some tasty bolts like your original gold one .

laters

if i have asked for help .thanks in advance for helping and giving me advice .. all the very best to you all .. respeck monkeymoves .......

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: Engine mount bolt knackered!
« Reply #11 on: January 19, 2010, 06:14:06 PM »
Is the new bolt the same strength (steel grade  either 8.8 or 10.9 but could be stronger)? That's just as important as the thread when replacing a bolt...
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

ciaoflyer

  • Super Member
  • ***
  • Posts: 1325
  • Karma: 3
Re: Engine mount bolt knackered!
« Reply #12 on: January 19, 2010, 06:20:41 PM »
Yes it's an 8.8 but has a wider pitch of 1.5, because the pitch is 1.5 it changes the strength to just over 4 tonnes, he said it would be fine...........
Ciao4Now

bis13

  • Super Member
  • ***
  • Posts: 2749
  • Karma: 39
Re: Engine mount bolt knackered!
« Reply #13 on: January 19, 2010, 07:15:51 PM »
i might have a spare knocking around in my garage i will have a look when i get a mo.

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: Engine mount bolt knackered!
« Reply #14 on: January 20, 2010, 07:36:16 AM »
Bearing in mind my bolt broke, it is a pretty valid question about the strength of that replacement bolt.

I'd carry a spare  :oops:
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)