Author Topic: Break a 126???  (Read 4070 times)

0 Members and 1 Guest are viewing this topic.

Captain Hazzard

  • Newbie
  • *
  • Posts: 11
  • Karma: 0
Break a 126???
« on: July 17, 2006, 10:39:57 PM »
At the weekend my new acquisition decided to throw a driveshaft, and at the same time knacker the hub and bearings.

Are those parts easy to get hold of, or should I break it? Would there be any interest in the parts from it? Its a 1985 air cooled.
I only wanted to be 16... and free

richard

  • Super Member
  • ***
  • Posts: 424
  • Karma: 0
seat
« Reply #1 on: July 17, 2006, 10:46:28 PM »
if you break it, can i have the front drivers seat if it aint wrecked?

Chris Lakin

  • Super Member
  • ***
  • Posts: 2105
  • Karma: 0
    • http://www.fiat126.co.uk
Break a 126???
« Reply #2 on: July 17, 2006, 11:36:45 PM »
woooooo, hang on a sec, whats all this about breaking it?

you could probably sort that for less than £40 from second hand spares, lets not have such hasty talk?  :lol:  Yes mate parts should be too bad to fined.

regards

Chris
+ SKYPE USERNAME: fiat126.co.uk
+ CLUB (ENQUIRIES): [email protected]

Captain Hazzard

  • Newbie
  • *
  • Posts: 11
  • Karma: 0
Break a 126???
« Reply #3 on: July 18, 2006, 08:13:09 AM »
Thats good news Chris. Where should I look for them though? Scrappers? 126 are a little short down here! And the garage who have got it at the moment have told me to source the parts. I'd much rather keep it than break it. And I can't afford another car!
I only wanted to be 16... and free

PaulB

  • Super Member
  • ***
  • Posts: 333
  • Karma: 0
Break a 126???
« Reply #4 on: July 18, 2006, 08:40:12 AM »
Someone else may be able to confirm this, but I think everything from the drive shaft to the entire hub can be swapped from a BIS to a 126P. That broadens your options. There are quite a few breakers websites where you tap in parts you're after and breakers will get back to you. Repairing it is the kind of job you could do yourself with a Haynes manual, or pay a mechanic a lot of money for as it will be time consuming (the gearbox needs removing if the driveshaft is knackered.

If you do give up on it, don't break it - my eldest son lives in Cornwall and is looking for a cheap 126 project!

Captain Hazzard

  • Newbie
  • *
  • Posts: 11
  • Karma: 0
Break a 126???
« Reply #5 on: July 18, 2006, 09:08:52 AM »
Can anyone else confirm this? That would be good news. Does anyone have a link to an online breakers site?

Cheers for all the help on this so far guys.
I only wanted to be 16... and free

PaulB

  • Super Member
  • ***
  • Posts: 333
  • Karma: 0
Break a 126???
« Reply #6 on: July 18, 2006, 10:42:59 AM »
http://www.breakerlink.com/
http://www.partsgateway.co.uk/

I used the parts gateway ages ago and found three complete (rusty) FSMs near me in Yorkshire. I am not endorsing these sites though - they may be sh*te? Watch out for premium rate phone lines etc.

You could google for others, or use http://www.yell.com to find local breakers yards.

You are looking for any 126 BIS or aircooler from the 80s/90s - you can confirm the parts are okay once you've found a 126. Can you describe/post pics of the damage - as it may not be all that bad and better repaired with new parts? for example if its just the torsion damper its less than £10. If you want to buy new, then Axel Gerstl will probably be the cheapest option:
https://ssl.kundenserver.de/shop.fiat500126.de/indexa.htm

slater

  • Super Member
  • ***
  • Posts: 215
  • Karma: 0
    • http://www.retro-rides.com
Break a 126???
« Reply #7 on: July 18, 2006, 08:52:21 PM »
https://ssl.kundenserver.de/shop.fiat500126.de/indexa.htm

for new parts, (probably not that expensive at their prices !)