Author Topic: kingpins  (Read 2447 times)

0 Members and 1 Guest are viewing this topic.

massa

  • Member
  • *
  • Posts: 46
  • Karma: 0
kingpins
« on: November 14, 2010, 06:31:58 PM »
someone must no are the king pins fitted to 126 bis the same through out the say 500 models and 126 models some say yay some say nay i would of thought yes but lot of time may be wasted trying thanks lads dave

dajwid

  • Subscribers
  • Super Member
  • ****
  • Posts: 2932
  • Karma: 14
Re: kingpins
« Reply #1 on: November 14, 2010, 06:47:13 PM »
Bis and AC are the same.

massa

  • Member
  • *
  • Posts: 46
  • Karma: 0
Re: kingpins
« Reply #2 on: November 14, 2010, 07:32:48 PM »
thanks so i take all 126 are the same and 500 are different thanks mate

dajwid

  • Subscribers
  • Super Member
  • ****
  • Posts: 2932
  • Karma: 14
Re: kingpins
« Reply #3 on: November 14, 2010, 07:35:24 PM »
Mmmmmm I would say they are the same but only know 126, not 500s.


massa

  • Member
  • *
  • Posts: 46
  • Karma: 0
Re: kingpins
« Reply #4 on: November 14, 2010, 08:06:35 PM »
thanks again one stub axle to sort will make sure i ask for 126 bis king pin kit then mot time run a rx7 for summer had bis a while so keen to get on the road big difference to rx but ave always loved little fiats thanks for help

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: kingpins
« Reply #5 on: November 14, 2010, 10:07:47 PM »
500 takes a smaller bearing thus the shaft is thinner.

I have a 500 and thought I could use some 126 king pin/knuckles/suspension bits on the front of it however the 500 bearings/drum wont go over the shaft hence the 500 is now on 500 rims at the back and 126 rims at the front :oops: only a temporary measure though [-/
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
Re: kingpins
« Reply #6 on: November 15, 2010, 06:33:02 AM »
Darrell is mixing up his front wheel bearings with king pins  :oops:
Any of the kits will do  [-/

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: kingpins
« Reply #7 on: November 15, 2010, 09:10:23 AM »
Isn't everyone just getting the re-conditioned ones on the net now as they are cheap?
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: kingpins
« Reply #8 on: November 15, 2010, 06:52:35 PM »
I renewed mine using a repair kit... though the front left is a re-conditioned one but i could've renewed 3 for that price!
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

massa

  • Member
  • *
  • Posts: 46
  • Karma: 0
Re: kingpins
« Reply #9 on: November 15, 2010, 07:38:11 PM »
my thoughts one kit for 40 quid does 2 stub axles good value me thinks thanks lads

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: kingpins
« Reply #10 on: November 15, 2010, 08:23:40 PM »
Putting the new kit in I found to be a bit of a bother :oops:
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: kingpins
« Reply #11 on: November 15, 2010, 09:18:00 PM »
It's difficult if it's rotted together (i had to hammer it for ages >:(). You also need that tool (broach?) to refine the inner surface of the kingpin sleeve...
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...