Author Topic: Dashboard Vynil & Vent removal tips  (Read 3198 times)

0 Members and 1 Guest are viewing this topic.

Aaron

  • Super Member
  • ***
  • Posts: 232
  • Karma: 0
Dashboard Vynil & Vent removal tips
« on: September 07, 2009, 05:44:15 AM »
G'day,

I'm revlatively new here having just aquired a 1990/91 FSM Niki which also came with a parts car.  Due to my lack of space available at home, I'm feverishly stripping all of the useful stuff off the parts car before recycling the rusty hulk.

I'm wondering whether anyone can help in suggesting how I get the centre dash air vents out?  I'm trying to remove this and the black vynil covering before cutting out the suprisingly good steel section below the windscreen out of the car to use on the road worthy one.  But the vents seem to be stopping me getting this vynil off.  I'd like to keep the vynil if possible as the old UV rays in Perth do ultimately kill this stuff, and the parts car one is in better nick.  Any suggestions?

Also does anyone have an electronic (PDF or the like) version of the workshop manual?  So far I've been relying on my memory on how my previous Lada Nivas were put together on taking it apart and it seems to be working.

Thanks
Aaron
1991 FSM Niki + 1990 FSM Niki quickly becoming a parts pile

Pete126

  • Administrator
  • Super Member
  • *****
  • Posts: 3369
  • Karma: 35
  • Location: West Yorkshire
Re: Dashboard Vynil & Vent removal tips
« Reply #1 on: September 10, 2009, 09:48:16 PM »
Hi Aaron, I'm not sure which dash they put in the Niki, Is it this one or the earlier type ???

Pete.      il cavallo piccolo

Aaron

  • Super Member
  • ***
  • Posts: 232
  • Karma: 0
Re: Dashboard Vynil & Vent removal tips
« Reply #2 on: September 11, 2009, 06:02:25 AM »
Yeah it's the later type pictured.  Right hand drive though.

Gordan

  • Subscribers
  • Super Member
  • ****
  • Posts: 1689
  • Karma: 8
Re: Dashboard Vynil & Vent removal tips
« Reply #3 on: September 11, 2009, 10:02:58 AM »
I remember some1 telling me that the only way is to rip it out :P
but seriously, the plastic went seems to be "welded" to other ventilation parts, so you can just smash it if you dont need it, or look under the bonnet and try to find the place it was joined with the other parts, i have a manual and it says nothing about this issue, plus ive managed to take out all the ventilation parts except this, so basically, there is no simple way. Good luck and let us know how you get on...
PLEASE FOLLOW MY PROGRESS ON IG: https://www.instagram.com/fiatbis/

phreak97

  • Super Member
  • ***
  • Posts: 576
  • Karma: 2
  • Niki!
Re: Dashboard Vynil & Vent removal tips
« Reply #4 on: September 11, 2009, 01:50:17 PM »
theres a trick to it!
I didnt know myself until after I'd gone the brute force route, I got a parts car like you did and stripped it. forcing it out didnt break it, but it quite possibly could.

theres four clips, two at the top and two at the bottom, you can see them in the photos below, theyre actually accessible from inside the vents, you should be able to get a flat screwdriver in there and unclip them.

http://i189.photobucket.com/albums/z234/phreak97/niki%20bits/11092009854.jpg

http://i189.photobucket.com/albums/z234/phreak97/niki%20bits/11092009856.jpg

:)

the dash vinyl has a bunch of clips that slot into the metal dash behind it, push them up towards the windscreen to unhook them.

have you by any chance got a good spare set of dash switches? mine are pretty crusty, and I'm in Adelaide so postage would be easy.

--
phreak97

Gordan

  • Subscribers
  • Super Member
  • ****
  • Posts: 1689
  • Karma: 8
Re: Dashboard Vynil & Vent removal tips
« Reply #5 on: September 11, 2009, 02:38:16 PM »
Wow thanx for that Phreaky, im gunna pop mine out just to clean it and see what happens  :P
PLEASE FOLLOW MY PROGRESS ON IG: https://www.instagram.com/fiatbis/

Aaron

  • Super Member
  • ***
  • Posts: 232
  • Karma: 0
Re: Dashboard Vynil & Vent removal tips
« Reply #6 on: September 12, 2009, 02:53:32 AM »
Phreak,  thanks for that.  It confirms what I thought I'd been seeing.  I'd tried getting at those from the dash side but it looks like trying from the back is better.  I'll give it a go.

On the switches front, unfortunately mine all seem to be in the same boat.  All of the markings have worn off and the switches have gone a light grey with the plastic starting to break down (some poeple still don't know about Amour-all's benefits to plastic.)  The parts car came with 2 dash surrounds one complete and the other with a couple of switches missing all are erqually as bad... :(

One of my many tasks will try to fix these up and re-stencil the symbols on them, but that's a way off yet, got to get the old shell gone first.

Is it worth salvaging the brakes, steering and suspension from these?  I'm at that point where do I leave it on or take it off?

phreak97

  • Super Member
  • ***
  • Posts: 576
  • Karma: 2
  • Niki!
Re: Dashboard Vynil & Vent removal tips
« Reply #7 on: September 12, 2009, 01:29:47 PM »
I dont think you can get to them from the back, but let us know how you go.

good switches DO exist.. my friend had a car with perfect ones.. b*******.

as for the suspension etc, keep whatever you have room for, niki parts are only going to go up in value. also the suspension can all be fitted to a fiat 500 as an upgrade, you should be able to offload it for a profit if you ever decide to clear out your spares later down the track.

I have heaps of instrument clusters etc, I got a lot of parts from a couple of people who used to wreck them for the motor and gearbox to put in 500's. still dont have much in the way of good switches though.
--
phreak97

Aaron

  • Super Member
  • ***
  • Posts: 232
  • Karma: 0
Re: Dashboard Vynil & Vent removal tips
« Reply #8 on: September 13, 2009, 11:11:51 AM »
Well I managed to free the vents.  The best method I found was to rotate them such that they would be bloing air full up and then inserting a screw driver between the dash metal and the vent plastic, push the clips down.  Once the vents moved forward a little, the clips released from the dash and the whole assembly just rotated out.

Unfortunately the vynil had hardened a little too much in the sun and it promply cracked in several places, despite my attempts to soften it with Armour-all over the week.  Seemed to be only the very top section closest to the windshield had gone hard, the backing and lower half of the covering was still soft and pliable - damn hole in the ozone layer!  :(

phreak97

  • Super Member
  • ***
  • Posts: 576
  • Karma: 2
  • Niki!
Re: Dashboard Vynil & Vent removal tips
« Reply #9 on: September 13, 2009, 12:55:59 PM »
A hairdryer seemed to do the trick for my boot lining, probably would have helped your vinyl too. even a bucket of hot water and a rag would have done the trick, I've done that too, that worked faster but didnt get as hot.

have you taken the glass out? the front and rear windscreens arent too hard to remove without breaking them or damaging the seals, you just get a friend to hold it from the outside so you dont drop it and break it, then push out on it while lifting the seal from the outer edge inside the car and pushing it in towards the window. I took the skin off one of my knuckles the first time because it gets to a point and gives way, exposing the sheet metal edge that it was clipped onto. start from one end and work your way across.


I just looked at your photos.. that parts car doesnt really look beyond repair, the one I had was much worse than that. what are the main things that were wrong with it? I assume you've already stripped it too far to save anyway..
« Last Edit: September 13, 2009, 02:01:27 PM by phreak97 »
--
phreak97

Aaron

  • Super Member
  • ***
  • Posts: 232
  • Karma: 0
Re: Dashboard Vynil & Vent removal tips
« Reply #10 on: September 13, 2009, 04:06:41 PM »
Um yeah, a bit too stripped.  Problem is that it had been unregistered for over two years.  In WA it's quite a bit of a pain re-licensing a vehicle.  Mainly the bonnet is more rust than steel, the panel below the rear window is completely rusted away, the floor on the drivers side is showing rust, the front light panel and outer guards are fairly rusty, the rear left shock tower is cut out of the car, etc...

It was probably salvageable but un-economic and as I put in the caption, the photo makes it look better than it was.

Yeah I also got the glass out by myself.  Pretty easy for one person with this size vehicle, with a little patience.

phreak97

  • Super Member
  • ***
  • Posts: 576
  • Karma: 2
  • Niki!
Re: Dashboard Vynil & Vent removal tips
« Reply #11 on: September 13, 2009, 10:48:48 PM »
ah ok probably not really worth it then..
the one I had had been tipped over, so the whole right side was flat and very rusty everywhere that the paint had cracked from bending. as well as lots of rust in all the normal places
--
phreak97

Aaron

  • Super Member
  • ***
  • Posts: 232
  • Karma: 0
Re: Dashboard Vynil & Vent removal tips
« Reply #12 on: September 14, 2009, 05:17:59 AM »
What's the normal places for rust in these?  The good one seems to have it under the windscreen where the drain tubing is, in the bottom of the passenger door (inside) and possibly in the lower rear corner of the left quarter panel. The last one might just be bent due to the dent, the underbody paint here is is intact but has come away from the panel.  Considering what russian steel used to be like, I thought that was pretty good for a 18 year old econo car. 

I suppose it helps that we don't put salt on our roads.

phreak97

  • Super Member
  • ***
  • Posts: 576
  • Karma: 2
  • Niki!
Re: Dashboard Vynil & Vent removal tips
« Reply #13 on: September 14, 2009, 08:14:21 AM »
typical places are under the lower corners of the front and rear windscreens above the drain tubes and can spread along beneath the rear window, next to the headlights (water sits under the boot seal by the corner), they rust in the sides of the boot lid, and in the engine cover in the bottom corners near the hinges, the door can rust behind the plastic and also around the lower hinges. mine's starting to rust in the drivers door along the window seal..
--
phreak97