Author Topic: Anyone going to Poland soon?  (Read 2429 times)

0 Members and 1 Guest are viewing this topic.

michaelodonnell500

  • Super Member
  • ***
  • Posts: 758
  • Karma: 7
Anyone going to Poland soon?
« on: January 25, 2008, 08:43:02 PM »
Hi.
I'm after a clutch plate for a 126 aircooled as I suspect my one is on it's way out.
Anybody going to Poland soon or can get one sent over?

Thanks

Michael
Rust does not discriminate

MaLi

  • Super Member
  • ***
  • Posts: 151
  • Karma: 1
  • Location: Leceister
Anyone going to Poland soon?
« Reply #1 on: January 28, 2008, 12:10:38 PM »
Hi!

Try to post an advert on this forum in english section. People are heplful so you might find someone to send you one to UK:

http://motonews.pl/sh_forum.php?op=fvf&c=0&f=25

Regards,

Mali

chipuk

  • Member
  • *
  • Posts: 26
  • Karma: 0
Anyone going to Poland soon?
« Reply #2 on: January 28, 2008, 05:19:35 PM »
hi.

not sure how the prices compare, but axel gerstl are very good, they dont charge stupid money for p+p either.

Article Number: 01010  18 euros.

ChrisRLewis

  • Administrator
  • Super Member
  • *****
  • Posts: 1723
  • Karma: 25
    • Club126uk
  • Location: Swansea, UK
Anyone going to Poland soon?
« Reply #3 on: January 28, 2008, 05:41:32 PM »
I would have thought they are still available from most motor factors? I wouldn't think that they cost much either?

are you after a clutch kit or just the clutch disk?

michaelodonnell500

  • Super Member
  • ***
  • Posts: 758
  • Karma: 7
Anyone going to Poland soon?
« Reply #4 on: January 28, 2008, 10:32:16 PM »
Hi.
I'm only after the disc.
Gerstl are very good, but i dont have a credit card. The polish stuff is just that little bit cheaper!

Michael
Rust does not discriminate

Pete126

  • Administrator
  • Super Member
  • *****
  • Posts: 3369
  • Karma: 35
  • Location: West Yorkshire
Anyone going to Poland soon?
« Reply #5 on: January 29, 2008, 12:17:30 AM »
Gerste want 28 euros for the plate and about 8 euros for post thats about works out to 28 quid,
Ring round the motor factors i'm sure you will do better than that locally.

you can buy a complete clutch kit online in GB for £37-50 + VAT

http://www.buypartsby.co.uk/clutch_kit_display.php?txtmodel=126&Submit=Next&txtmake=Fiat
Pete.      il cavallo piccolo

chipuk

  • Member
  • *
  • Posts: 26
  • Karma: 0
Anyone going to Poland soon?
« Reply #6 on: January 29, 2008, 12:59:24 PM »
Quote from: "pedro126"
Gerste want 28 euros for the plate and about 8 euros for post thats about works out to 28 quid,
Ring round the motor factors i'm sure you will do better than that locally.

you can buy a complete clutch kit online in GB for £37-50 + VAT

http://www.buypartsby.co.uk/clutch_kit_display.php?txtmodel=126&Submit=Next&txtmake=Fiat


28 euros for a bis , 18 for 500/126 aircooled.I looked at the picture in micheals avatar, and assumed it was for an air cooled as it was in a 500.

hudsonhenry

  • Super Member
  • ***
  • Posts: 303
  • Karma: 1
    • http://www.retro500.com
Anyone going to Poland soon?
« Reply #7 on: January 29, 2008, 01:20:04 PM »
I would change the pressure plate and the bearing, if the friction plate is worn then the other components, whilst probably not visibly worn, must be heading in that direction.

If you do it once properly it should last for a good number of years, try and save a few quid now and you will probably be taking the gearbox out agine in the near future to change the other bits as they pack up.


Nigel
http://www.retro500.com the site dedicated to modified Fiat 500's

Pete126

  • Administrator
  • Super Member
  • *****
  • Posts: 3369
  • Karma: 35
  • Location: West Yorkshire
Anyone going to Poland soon?
« Reply #8 on: January 29, 2008, 06:44:28 PM »
I do apologise Chipuk. it works out to just under 20quid for the plate and post, my point was that it is possible to buy parts locally ie, Tomorrow at a similar price.
As hudsonhenry pointed out if the jobs done properly you don't need to worry about the other component's failing
Pete.      il cavallo piccolo

michaelodonnell500

  • Super Member
  • ***
  • Posts: 758
  • Karma: 7
Anyone going to Poland soon?
« Reply #9 on: January 29, 2008, 09:35:18 PM »
Fear not, it will be done properly!
I've already picked up the other parts on ebay over the last 6 months, just haven't found a plate at a nice price yet.
Rust does not discriminate