Author Topic: Break drum removal  (Read 2666 times)

0 Members and 1 Guest are viewing this topic.

ciaoflyer

  • Super Member
  • ***
  • Posts: 1325
  • Karma: 3
Break drum removal
« on: February 12, 2010, 08:13:32 PM »
Gone to remove the dums on the rear, is it true that the little holes to fit a puller to are M9?
Ciao4Now

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: Break drum removal
« Reply #1 on: February 12, 2010, 11:16:59 PM »
Think they are M10  :oops:
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

ciaoflyer

  • Super Member
  • ***
  • Posts: 1325
  • Karma: 3
Re: Break drum removal
« Reply #2 on: February 13, 2010, 07:40:06 AM »
Wentto an engineering supplier and M10 would not fit, tried an m9 tap and it went in but he has no m9 bolts cos it is an unusual size?
Ciao4Now

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
Re: Break drum removal
« Reply #3 on: February 13, 2010, 07:49:36 AM »
I think that it is a case of getting the right pitch thread on an M10 bolt  [-/

ciaoflyer

  • Super Member
  • ***
  • Posts: 1325
  • Karma: 3
Re: Break drum removal
« Reply #4 on: February 13, 2010, 12:08:34 PM »
Right, took it back to the engineering shop and tried all sizes of M10 and they are too big, it is deff M9 as M8 is also too small.  Guy said that the automotive industry use obscure type bolts because when you go in they wan't to sell you a new hub! 

Gonna try and get some on Ebay!
Ciao4Now

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: Break drum removal
« Reply #5 on: February 13, 2010, 02:55:39 PM »
If the drum is seized then a final alternative maybe to fit the wheel onto  the hub and try to knock it off with a large hammer by hitting the tyre and rotating the wheel at the same time. Best to use a wheel with a worn tyre and to be careful not to hit the wheel rim.
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

ciaoflyer

  • Super Member
  • ***
  • Posts: 1325
  • Karma: 3
Re: Break drum removal
« Reply #6 on: February 13, 2010, 04:09:32 PM »
If the drum is seized then a final alternative maybe to fit the wheel onto  the hub and try to knock it off with a large hammer by hitting the tyre and rotating the wheel at the same time. Best to use a wheel with a worn tyre and to be careful not to hit the wheel rim.

Thanks for reply but surely this can't work as the wheel bolts through the hub.
Ciao4Now

GTMaster

  • Super Member
  • ***
  • Posts: 809
  • Karma: 2
  • Na most a tuti- tuti- tuti
Re: Break drum removal
« Reply #7 on: February 14, 2010, 05:17:09 PM »
 Yes that is true.  :oops: Now you mention it i had done this on a car that had the wheel studs on the drum and used wheel nuts. This still can work if you need to take the hub off as well...
« Last Edit: February 14, 2010, 05:18:45 PM by GTMaster »
"One more drink, Lacikám?"

All about car restoration can be found in the song
"Got my mind set on you" by George Harrison...

michaelodonnell500

  • Super Member
  • ***
  • Posts: 758
  • Karma: 7
Re: Break drum removal
« Reply #8 on: February 14, 2010, 08:33:25 PM »
I have removed them in the past by hitting the drum on the edge with a hammer.
Left side, then right side in turn which should push the brake shoes together and reduce the force holding the drum on.
I've never found a drum that couldn't be removed with10 minutes hammer persuation!
Rust does not discriminate

Jan-in-UK

  • Super Member
  • ***
  • Posts: 533
  • Karma: 5
Re: Break drum removal
« Reply #9 on: February 14, 2010, 08:46:40 PM »
Michael is right. Plus few hits from behind can also do the job easier :) hummer - most universal tool of all.
Such a thing as Fiat 126p will never happen again to this planet... Love it.
www.fsoclub.co.uk

bis13

  • Super Member
  • ***
  • Posts: 2749
  • Karma: 39
Re: Break drum removal
« Reply #10 on: February 20, 2010, 04:04:42 PM »
i too live in the hammer camp also if you are getting new shoes at the same time a little help with a screwdriver.

neilW

  • Member
  • *
  • Posts: 29
  • Karma: 0
Re: Break drum removal
« Reply #11 on: March 15, 2010, 03:04:03 PM »
is this a common problem??as mine are starting to stick. its happened twice in the last 10 days. they got so hot by the time I noticed, (on a motorway), i had to pour water on to cool them down, was like pouring water into a roasting hot pan on the hob. SIZZZZLE!!

 ???

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
Re: Break drum removal
« Reply #12 on: March 15, 2010, 03:19:13 PM »
Are you talking about fronts & rears or just rears. If the brakes are binding all round then the master cylinder would need looking at. If it is just the rears then could be handbrake not releasing correctly or seizing wheel cylinders  [-/

landyman

  • Super Member
  • ***
  • Posts: 127
  • Karma: 2
Re: Break drum removal
« Reply #13 on: March 15, 2010, 08:11:09 PM »
fine adjustment tool No.1 always works, if not use fine adjustment tool No.2 [the bigger hammer] or manchester screwdriver. </                         :oops2: giving away trade secrets now