Club126UK
Fiat 126 Chat => Fiat 126 Mechanical Problem Solving => Topic started by: Jan-in-UK on June 25, 2010, 08:33:58 PM
-
Story goes - we fired up my brand new engine inside the green one - lovely sound, runs sweet and everything was superb. Then I switched it off to proceed with the other jobs but I left ignition ON and after more or less 2h coil started to make strange sounds :) and melting itself :D
So ok, coil f***d I thought. I got hold of a new one, put wires the same way, NOTHING else was changed. And it does NOT start up what so ever. Obviously gets flooded every single trial. Checked cables 3 times, everywhere..... WHY?????
IS THERE ANYTHING ELSE WHICH GOES "BYE BYE" TOGETHER WITH BLOWN COIL?????? I will get crazy, co close to completion.
-
Check the points are opening and closing they can weld themselves together.
Swap the condenser.
check the fuses.
-
Will do. Fuses are ok, so maybe one of other two issues :(
-
Also if you have a multimeter or a circuit tester check you have 12v on the + side of the coil. its not unknown for it to take out the the wire to the ignition switch.
-
the +12v to the coil is fine, but we werent able to stick another condenser on it. That was my first thought. ?Didn't think about the points welding themselves, good idea
-
I gave Jan a help with this earlier, and I'm baffled!
I drove to his in my 500, then removed my coil (wasted spark), distributor, condenser and plug leads and put them on Jan's 126 - No spark!!
I also checked the plugs, then ran a jump lead from the +ve side of the coil to the battery, and the coil mount to the -ve, still no joy.
I cannot figure out whats wrong since all the parts work when they're fitted to mine!!!
Any ideas would be a big help!!
-
I can only confirm I am getting grey haired as well and it would be really great help if someone would come up with idea what is wrong :rant:
-
could it be a break in the wiring harness?
-
this may sound stupid but when you refitted the coil did you make sure that the point of contact with the body has a good earth?
-
I was checking the multimeter from the +ve of the coil through to the block, so it must have been earthed ok, but just to confirm, the last test involved connecting the coil earth to the -ve battery terminal and the +ve coil to the +ve of the battery as I figured this would pick up on any dodgy earth or corroded wires
-
Have you checked the wire from the coil to the distributor ???
-
I made up a new one, then checked for open/closed circuit while turning the engine and it all seemed in order!
-
Thats a puzzle. so the distributor cam is rotating with the engine, Have you tried measuring from earth to the points or do the points spark when you flick them ???
-
Reading from the start of the thread it states that the coil got cooked after the ignition was left on i can only assume that there is some part of the loom that has given up due to this?
-
All parts of the loom, high voltage leads and all mechanical parts were taken off michael 500 - still doesnt work. As michael said we even put battery voltage strait to the coil without loom on the way!! I am getting slightly angry .:)
-
Lets start at the beginning.
Have you got 12v at the coil ???
Have you got 12v at the points ???
Have you got the isolation washers on the points and the distributor body ???
Have you got a spark at the plugs ???
Does the distributor cam rotate with the engine turning ???
Do the points open and close ???
Have you tried push starting the car or towing it round the block just in case the starter motor is taking too much power out of the battery.
-
Have you got 12v at the coil - Yes
Have you got 12v at the points didn't take a voltage measurement at the points, but I measured a closed circuit between the points and the -ve side of the coil, which answers the same question
Have you got the isolation washers on the points and the distributor body - yes
Have you got a spark at the plugs no.
Does the distributor cam rotate with the engine turning yes
Do the points open and close yes
Have you tried push starting the car or towing it round the block just in case the starter motor is taking too much power out of the battery. no, but I did couple up my working battery to the car which didn't solve it
I drove to his in my 500, then removed my coil (wasted spark), distributor, condenser and plug leads and put them on Jan's 126 - No spark!!
I also checked the plugs, then ran a jump lead from the +ve side of the coil to the battery, and the coil mount to the -ve, still no joy.
I cannot figure out whats wrong since all the parts work when they're fitted to mine!!!
-
Hi Micheal,
It has to be a fault in the wiring, If you disconnect the wire to the distributor there should be 12v on the neg' side of the coil measured down to earth, Just as if your setting the static timing.
-
A closed circuit between the points and ve won't be good enough.
Take the wire off the points and earth it intermediately against somewhere. If you can induce a spark this way the points are knackered and are earthing out somewhere inside the dizzy.
This earthing out could be within the points mechanism, I've had this on a relatively new set of points.
-
so what electrics have you got that work on the car?
-
A closed circuit between the points and ve won't be good enough.
Take the wire off the points and earth it intermediately against somewhere. If you can induce a spark this way the points are knackered and are earthing out somewhere inside the dizzy.
This earthing out could be within the points mechanism, I've had this on a relatively new set of points.
Thanks Darrell, but I know the points, dizzy and coil are good. I took them from my running 500, fitted them to Jans 126 which wouldn't start, then re-fitted them to my 500 and drove home. As far as I can see, the only variables left are the mechanical drive from the dizzy, which works, and the +ve lead to the coil and the lead between the dizzy and the coil.
Pete, I suspect it is wiring as there's not a hell of alot left!!
I haven't tested the -ve side of the coil down to earth but will give that a shot.
I assumed running a jump lead from the earthing bracket to the battery would have ruled this out, but I'm open to offers as this is doing my head in!!
-
Hi Mate keep plodding away [-/ While you have your meter out check the voltage on the + POS wire on the coil down to earth, You mentioned that you have 12v but what happens when the engine is being cranked ???
As long as the coil is bolted to the car there should not be an issue with the earths, If you need to pickup a permanent live in the engine compartment you can do that from the alternator which is easier to get to.
-
If I remember right the coil voltage was 11.2v (still cranking well so no problems as far as I could tell)
While cranking the voltage dropped to 10.v I think, but I've had my 500 start on less
-
The reason i asked was to rule out a fault with the ignition switch and wiring from the coil, to front of the car, we are clutching on straws here (scratches head) ;D
-
Hi All,
Just been reading the comments to date, it's just so frustrating when your so close. I hope this may help but you propreley done this already as i am a little slow. OK the twin spark coil has 12v to it and you have run a jumper wire to the coil to prove this is ok (so supply is ok), on the twin coil the + and - terminals do not require the coil base to be connected or bonded to body earth to function as like a conventional coil would.
1, With the points open on the cam and all wiring connected you should have 12v at both sides off the coil (ignition on).
2, With the wire coming from the distributor disconnected from the - side off the coil connect your ohm meter to the distributor wire and the other ohm meter lead to a good earth point on the car. Now turn the engine by hand so the cam in the distributor operates the points and the meter reading should go from fully open circiut to fully short circiut and nothing other than this. Any suspect readings should be investigated.
Just one other thing both spark plugs, both HT leads must be in the circiut to get a spark, so a suspect lead or plug will cause complete failure to spark.
Hope this helps [-/
I know you used parts from Micheals car but did you changed the distributor complete or just the points and condensor? The reason i ask is that there is a insulated part on the distributor that may be damaged due to the meltdown of the coil as the points closed would have been in this circiut.
-
Hi Smallcox, nice 126 BTW!!
It was the complete dizzy swapped during the testing.
I was not aware that both leads had to be connected during this. After the parts were swapped, at each stage Jan tried to start it while I help the plug against the block to watch for a spark, so this could be a big issue.
I think I'll have to try swapping the parts again, but with the leads attached this time.
Out of interest, why do both HT leads need to be connected to get a spark?
Thanks
Michael
-
Its a wasted spark system. Both leads fire H.T. at the same time. One cylinder would be on compression stroke the other cylinder would be on exhaust stroke, hence wasted spark system.
The H.T. spark runs down one H.T. lead uses the engine as the earth - then the H.T. runs back up the other H.T. lead back to the coil, This then makes the complete circuit between the coil & earth. So you do need to have both H.T. leads connected to make the wasted spark system work.
If you only try with one H.T. lead connected you will find a very low Kv.
Regards Gren.
Out of interest, why do both HT leads need to be connected to get a spark?
Thanks
Michael
[/quote]
-
swap in the entire system from the 500 including the spark plugs and try again?
also in a 126 the green wire to the coil is actually a ~1m length of resistive wire.. if you jumper +ve straight to the coil, dont leave it on there for too long, it isnt meant to get full battery voltage.
also, did you replace (or remove) the noise suppressor on the coil?
-
As mentioned above the twin coil pack does require a resistor in series with the low tension side off the coil. I have tryed to find out how the HT side off the coil is wound to explain why both spark plugs must be connected but failed. I can only quess that the windings are centre taped and have to callapse at the same time to create a spark.
-
I will definitely go crazy if it won't start before weekend :oops: lost my intrest in putting interior back together because of this s**t coil/leads/loom/points/sparks problem....
-
Going crazy is part of owning a 126 :P SMILE you'll get it sorted
-
As mentioned above the twin coil pack does require a resistor in series with the low tension side off the coil. I have tryed to find out how the HT side off the coil is wound to explain why both spark plugs must be connected but failed. I can only quess that the windings are centre taped and have to callapse at the same time to create a spark.
Yes the coil primary is connected to the secondary as one plug fires positive and the other plug fires negitive making the complete circuit. one plug fires from the centre electrode to the earth . the other plug fires from the earth electrode to the centre . the positive plug always wears out first. regards Gren.
[/quot
e]
-
I just did this at trade school, the secondary winding has no internal connection like it does on a single coil, each end of the winding is connected to a spark plug, so if you remove the connection to one of the plugs youre leaving one end of the secondary open and removing the whole circuit.
-
I just did this at trade school, the secondary winding has no internal connection like it does on a single coil, each end of the winding is connected to a spark plug, so if you remove the connection to one of the plugs youre leaving one end of the secondary open and removing the whole circuit.
[/
Correction.
quote] Yes i must have had a brain storm. using an ohm meter between the two low tension terminals you would get a reading of 1.3 to 1.6 ohms on a ballast ign coil. then on the two H.T. chimneys you would get a reading of 5000 to 10000 ohms. so has you said there is no internal connection.
On a normal 1 chimney (points coil) you would get a reading of around 3.ohms on the primary terminals. Then connecting ether side of your low tension terminal with the secondry H.T. chimneyyou would get your secondary H.T. reading of 5000 to 10000 ohms reading. hopefully this clears up any confusion. Regards Gren.
-
you could try connecting up the old single coil setup from a 500 if you have access to one, that'd rule out your twin spark problem, but try new spark plugs first.
I feel like I could get this car running if I could see it for myself.. I think I'm kind of far away though:P
-
swap in the entire system from the 500 including the spark plugs and try again?
also in a 126 the green wire to the coil is actually a ~1m length of resistive wire.. if you jumper +ve straight to the coil, dont leave it on there for too long, it isnt meant to get full battery voltage.
also, did you replace (or remove) the noise suppressor on the coil?
I wonder if this green wire could have been causing me bother with the 123 ignition.... :-X
Will check that tomorrow as I am very sad to have taken the 123 out.
-
I feel like I could get this car running if I could see it for myself.. I think I'm kind of far away though:P
Thanks for the words of encouragement, but It's not been as easy as it should be, or it would be running now I can assure you!
-
yeah no doubt, Ive had problems like this which just dont make sense as well. But persistance is all you need. You need to check each part individually and make sure it works properly, and keep an open mind, the problem probably isnt where you expect.
Have you checked if thwe earth strap between the body and the alternator is making good contact?
If you were using the green wire as the 12v input to the 123 then it could have caused problems for sure. Follow thw green wire along the firewall, just before it disappears into the car theres a plastic joiner and the wire changes colour, thats where your 12v from the ignition will be.
Otherwise you can run a wire from the alternator or starter motor then have a relay operated by the green wire to make it switch on with the ignition. Thats probably the best way to do it with the least voltage drop, but either way should work fine.
-
I'll be green wire hunting :oops:
I wish Jan lived closer or I'd pop-over and do some head scratching together there. :-X
It always sounds like it should be easy to sort on the forum but I know 126's have gremlins running around in them from new that are placed in the car to keep one guessing :oops:
-
If you were using the green wire as the 12v input to the 123 then it could have caused problems for sure.
It's not using a 123, as for the other checks please read the earlier parts of the thread as I have already checked the entire system. I will have to re-test with both plugs connected, but I've not been round to help for a few days as my plate is rather full at the moment!
-
Good Morning from New Zealand Jan.
I am following this tread with interest. My 126 P4 has the older standard ignition system as used on thev 500 so I can't help with any info there and I have not had anything to do with the redundant spark system.
If I were there I would go back to the basics by removing the rocker cover and checking the valve timing, resetting the tappets and then based on what I have read, fit a complete ignition system of the older type (coil, distributor with new points and condensor, rotor, cap, leads, plugs). Then with the rocker cover still off make sure that it was firing the correct plug and set the ignition timing. I would then power it up from an external battery so the vehicle system had no input other than operating the starter. That would be +ve to +ve side of the coil and -ve to a good earth on the motor, testing all connections with a multi meter or test light. Then without turning on the key pull the starter and it should go. I hope I am not trying to teach Grandma to suck eggs. What I have suggested will prove that the motor is a runner and that all that hard work was worth it. (It will make you feel good just to hear it run). Good luck and keep us all posted.
Allan
-
I would like to thank all of you - my car does work now :) Darell came over and cured it with a nice help and advice from Michael. In the end of the day we still don't know what caused the problme as Darell has check and connected all these bits from a scratch. Fact is - none of the wasted spark coils (3!!!) works on this car. At leas one works on Michels 500.... Se we ended up setting timing, checking points and connecting.... TWO SINGLE COILS with each other and it does run. So all I need is double connection round standard coil (the one looking like single silver one but with two sonncetors for leads).
Does anyone has ONE kicking about????!!!
NEED TO GO UXBRIDGE this weekend !!!!
BTW: In good mood so I fitted few rare accesories to my 126 today - have a look in resto.