Author Topic: Head rests  (Read 2113 times)

0 Members and 1 Guest are viewing this topic.

edsaysyes

  • Member
  • *
  • Posts: 80
  • Karma: 0
Head rests
« on: December 13, 2010, 09:55:25 PM »
How do the head rests come off  I  have been looking for where I put the angle grinder but before I do it that way I just thought I would see if here was a better way

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: Head rests
« Reply #1 on: December 13, 2010, 10:14:23 PM »
Can you not lift the material up to see if there is a bolt or something on the inside of the seat?
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

edsaysyes

  • Member
  • *
  • Posts: 80
  • Karma: 0
Re: Head rests
« Reply #2 on: December 13, 2010, 10:22:49 PM »
The collars on the rods holding the headrests are nice and neat against the seat covers Can't feel anything underneath so might resort to a large screwdriver underneath to see what happens. Has me totally mystified but then again I am easily confused at times.

gsxr126

  • Super Member
  • ***
  • Posts: 405
  • Karma: 0
Re: Head rests
« Reply #3 on: December 13, 2010, 10:54:25 PM »
I'm in the same boat as u ed, has me totally mystified. Judging by the way they side up and down u would think there would be a clip the u can fit a blade into to release it fully but :cry:
The Good - White Niki all Std Daily Driver, The Bad - Black Niki GSXR1300 BMW diff & suspension, The Ugly - Red Niki quietly Rusting In Peace

Aaron

  • Super Member
  • ***
  • Posts: 232
  • Karma: 0
Re: Head rests
« Reply #4 on: December 14, 2010, 07:42:45 AM »
If it's anything like the Ladas, and the build techniques I've seen thus far on the 126p say they are built in a similar manner, the head rest probably has a clip attached on the end of one of the rods.  I don't know what you call these clips but its like the one you use on trailer hitches in the picture below.  The only way to access these (from the Lada standpoint) was to remove the upper seat cover and yank this pin off.

Rusty's Uncle

  • Subscriber VIP+
  • Super Member
  • *****
  • Posts: 2837
  • Karma: 34
Re: Head rests
« Reply #5 on: December 14, 2010, 01:04:24 PM »
I have got a pair of seat frames that came from a 126 Brown which I believe was the first 126 to have head rests. posting a couple of pics to show the top of the back frame & the mount tubes . Also the head rest stems have a series of dimples that locate on that clip to set the height then a deep all round groove at the base to prevent the head rest coming right out. You will probably need to release the back cover at the base and slide it up to gain access to those clips  [-/

edsaysyes

  • Member
  • *
  • Posts: 80
  • Karma: 0
Re: Head rests
« Reply #6 on: December 14, 2010, 07:48:19 PM »
Hi Thanks both of you for the advise Thinks its a job for the weekend as the old seat covers that someone fitted will do until then

Darrell

  • Super Member
  • ***
  • Posts: 1715
  • Karma: 4
    • facebook profile
Re: Head rests
« Reply #7 on: December 14, 2010, 09:12:21 PM »
I don't like the look of those spikes :o

What if the seat gets bent so the spikes come out in an accident? :-X
'84 aircooled 126 & 500F still in kit form
Not the only African in the village :)

gsxr126

  • Super Member
  • ***
  • Posts: 405
  • Karma: 0
Re: Head rests
« Reply #8 on: December 14, 2010, 10:12:21 PM »
Cheers guys,

didnt realise the fabric is actually a cover you can take off :oops:
The Good - White Niki all Std Daily Driver, The Bad - Black Niki GSXR1300 BMW diff & suspension, The Ugly - Red Niki quietly Rusting In Peace