Author Topic: New Owner of a 1990 705cc 126 bis  (Read 2425 times)

0 Members and 1 Guest are viewing this topic.

Alex

  • Member
  • *
  • Posts: 96
  • Karma: 2
New Owner of a 1990 705cc 126 bis
« on: July 16, 2009, 12:40:08 PM »
Hi, just bought a 126 bis for my fiance, she's over the moon, but it needs a few jobs doing on it, one of them being the brake master cylinder, as i understand it it is almost impossible to find a workshop manual for this car, i have seen various screenshots online but would prefer a proper manual,

is it possible to use a haynes manual for the previous model to undertake works on the car?

any help would be greatly appreciated

Alex :):)

Maddog

  • Super Member
  • ***
  • Posts: 110
  • Karma: 0
Re: New Owner of a 1990 705cc 126 bis
« Reply #1 on: July 16, 2009, 01:29:05 PM »
Hi Alex, welcome to 126 land,

apart from the engine, most of the components are exactly the same design, most are interchangeable,
  the master cylinder is a doddle to change, have a look under the front of the car and you will be able to see it sticking out of the bulkhead, if you pull the carpet back from under the pedals you will be able to see the mounting bolts, I seem to remember having to unbolt the brake pedal assembly from inside the car first when I did the 500, not 100$ sure why off the top of my head, think you have to pull the whole assembly out then unbolt the M/cyl from the bracket.
 so in order,
 free off all 4 bleed nipples on the brake cylinders, if any  snap you'll need to replace that cylinder.
 
drain out the brake fluid by opening a bleed screw, put a bit of rubber tube on it into a jar and pump the pedal.
loosen the 2 brake unions on the master cylinder, if they round or twist the pipe you will probably want to replace that section of pipe.
remove the pipes from the M/cyl

unbolt the brake pedal/master cylinder assembly

before refitting/bleeding, check the condition of all brake pipes, now would be the easiest time to replace any that are corroded or suspect.

bleed the 2 rears first, then the fronts, then repeat.

I presume you have already sourced a replacement cylinder?

good luck, Richie

 

Gordan

  • Subscribers
  • Super Member
  • ****
  • Posts: 1689
  • Karma: 8
Re: New Owner of a 1990 705cc 126 bis
« Reply #2 on: July 16, 2009, 01:32:13 PM »
Hello, and welcome. you can buy a bis workshop manual in the shop section of the forum http://fiat126clubuk.freepgs.com/shop/index.php?main_page=product_info&cPath=1&products_id=1&zenid=mbhhn6ndm6ggfc0leoij5307p2 it has everything on the bis.  [-/
PLEASE FOLLOW MY PROGRESS ON IG: https://www.instagram.com/fiatbis/

Alex

  • Member
  • *
  • Posts: 96
  • Karma: 2
Re: New Owner of a 1990 705cc 126 bis
« Reply #3 on: July 17, 2009, 08:49:14 AM »
Hi Richie,

thanks for the advice on the master cylinder [-/, i have found a few places that sell them online
i came across this site which looked particulary good

https://webshop.fiat500126.com/index.php/sites/view/50-1-homepage.html

any advice on what other things i should look out for?

Regards
Alex

Maddog

  • Super Member
  • ***
  • Posts: 110
  • Karma: 0
Re: New Owner of a 1990 705cc 126 bis
« Reply #4 on: July 17, 2009, 02:42:46 PM »
[quote=""Alex]any advice on what other things i should look out for? [/quote]

 spray the bleed nipples with Plus gas or similar a couple of days before,
 a decent flare nut spanner will prevent any damage to the brake unions,
 perished flexi pipes, yours are close to 20 years old,
  and as a new owner, grease the front kingpins whilst your under there, they need done regularly.

Axel gerst is pretty good, maybe email him first to check he has it in stock though, although your local decent motor factors will probably have most brake components listed, if you need it quickly then they can be worth a phone call.

cheers, Richie