Club126UK

Fiat 126 Chat => Tuning & Customising 126 Models => Topic started by: thepuddlejumper on June 16, 2014, 02:09:24 PM

Title: Scuby 1800cc install
Post by: thepuddlejumper on June 16, 2014, 02:09:24 PM
I had some free time on Sunday so cut out the adaptor plate for the scuby to 126 gearbox, the trial fit went very well.  I need to get this complete to allow me to fire up the engine.

Ralph
Title: Re: Scuby 1800cc install
Post by: Gadge on June 16, 2014, 04:29:56 PM
Wow your fitting a scooby engine to a 126 box?  :o do you think it will take the power?
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on June 16, 2014, 09:53:43 PM
Z cars have fitted the same engine into a 500 with a 126 box and Alistair down in OZ has also done this conversion. Look up fiat 500 with Subaru engine on you tube

https://www.google.co.uk/url?sa=t&source=web&rct=j&ei=flifU8qnEczEPPf-gLAB&url=http://www.youtube.com/watch%3Fv%3DaA2ecWsngr0&cd=5&ved=0CDEQtwIwBA&usg=AFQjCNH_Y-effCdlQ8KJxQ5I45MKHl4IHQ

Ralph
Title: Re: Scuby 1800cc install
Post by: Pete126 on June 16, 2014, 10:35:30 PM
Great work Ralph will it be ready for RetroRides ;D

Wow your fitting a scooby engine to a 126 box?  :o do you think it will take the power?

Checkout Hudsonhenry's 500 site Engine Swaps

http://www.retro500.com/home.html
Title: Re: Scuby 1800cc install
Post by: mwub90 on June 21, 2014, 12:18:30 PM
Hey there
I too am trying to squeeze an ea81 into a 126, i found my engine on a farm so I'm currently rebuilding it.
I see you're using the 126 clutch, I wanted to use the subaru clutch but couldn't figure out how to mate it to the gearbox. If it's possible and you have them could you please post or send me the blueprints/plans of the boss and plate.
Good luck with the build, hope to see it up and running.
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on June 21, 2014, 09:50:48 PM
I have a drawing of the boss but the bolt holes for the scuby crank are offset, the PCD is the same for all the holes but there is one  pitch between the holes larger than the rest.  I used the original scuby flywheel to drill the holes in the boss, well to mark the correct positions.  I have opted to use a 5mm aluminium adapter plate, this should be OK but if you want to use a thicker plate them the boss would have to me amended to ensure the starter ring gear matches with the starter.  The clutch is from a panda I think, I will check and post later.  I have taken some more photos and will upload later, as my computer is down.  I am attempting to use the 126 starter, but have been told it may be a bit on the light side so I am trying to get hold of a cinq starter in the hope it is an easy mod to fit. One problem is the bolts which hold the scuby flywheel to the crank are 9mm x 1mm pitch' you will have to have these made as this is not a standard size.  You can use the scuby flywheel but you have to make an adapter plate to suit, look at light aircraft mods, this engine is very popular with home build light aircraft protects.  I made a plywood template for the adapter plate and transfered this to the aluminium , if you would like I can trace the plate.

Ralph
Title: Re: Scuby 1800cc install
Post by: Rusty's Uncle on June 22, 2014, 01:29:56 PM
Hi Ralph , I discovered the other day that m9 x 1mms pitch bolts are used on some BMW engine applications. Might be worth having a chat with your local BMW guys.


Sent from my iPad using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on June 22, 2014, 05:59:47 PM
Rusty thanks I will' I had a local engineering shop machine some m10x1.25 down to m9x1. I am not sure how good the thread is, still to torque them up, only at the set up stage. I have now fitted the starter, but battery flat so I hope to turn over soooon.

Ralph
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on June 23, 2014, 05:42:56 PM
Did some more work at the weekend, finally bolted together and turned over the engine even with a knackered battery.  All seemed to work, now need to fuel up find a good battery and fire it up.  Getting there slowly.  The first photo shows all the M9XImm caps, needed as bolt heads take up too much room.  The second and third show the starter in place prior to bolting engine and gearbox together.

Ralph
Title: Re: Scuby 1800cc install
Post by: dom.kellett on September 24, 2014, 09:49:05 PM
How's this going? Have you got any tips or online blueprints for the fitment your using so it's actually in car? I don't think I will struggle too much with that bit of fabrication for gearbox, I know it'll be tricked but I understand that, wanting to do the same so any thoughts of how to make it easier?


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on September 25, 2014, 12:57:20 PM
Not done a lot, I tried to start it using a 126 starter although it would turn the engine it was sporadic, I burnt out the starter.  Bought a brand new Subaru pickup starter off ebay and set about making an adapter plate which would use both the 126 and Subaru mounts.  Before I amended the new starter I decided to check it worked, after watching fake Britain, it worked fine but turned clockwise the scuby requires an anti-clockwise starter >:( >:( >:( >:( long story but was reimbursed now on the lookout for a starter.  I will update later hopefully with it running.

Ralph
Title: Re: Scuby 1800cc install
Post by: dom.kellett on September 25, 2014, 01:04:06 PM
Oh dear, not good to hear, I'm off for a full scooby then not selling any of it until I've sorted my engine


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on September 25, 2014, 01:14:40 PM
The engine I am using is out of a pickup, it is 1800cc and naturally aspirated.  I f you intend to use  the more modern scuby engines 1.6,1.8,2.0 you will need to get the wiring harness and ecu.  If I make a success of the pickup engine conversion I may go for a 2.0 modern engine.  If you want to go the whole hog you can get reverse diff  internals from Australia I think the company is called scuy gears.  This converts the scuby gearbox to run backwards therefore you can fit scuby engine and gearbox in the 126, Z cars have done this conversion with a 2ltr turbo.

Ralph
Title: Re: Scuby 1800cc install
Post by: dom.kellett on September 25, 2014, 04:29:53 PM
Is it tricky to fit the newer scooby engines and gearbox to the 126 or not too difficult? I'm wanting to put mx5 subframes on too, thanks for the advice and help, hope to see you out and running soon
Dom


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: poxxxy on September 25, 2014, 11:02:13 PM
Nice work :). Is there no way to get the starter to turn the other way (no good now but might of been an option)? Perhaps reverse the polarity? Depends on the construction of it I guess!
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on September 27, 2014, 07:46:15 PM
You can reverse the starer but it too difficult. Fitting the scuby starter isn't difficult, all you need to do is make an adapter plate and make the access slot in the side of the bellhousing a bit larger to take the larger diameter scuby starter.
Ralph
Title: Re: Scuby 1800cc install
Post by: dom.kellett on September 27, 2014, 09:17:38 PM
What about fitting the scooby engine, gearbox and starter? Would that be easier than making an adaptor plate for the 126 gearbox


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on September 28, 2014, 07:12:21 PM
I believe this would be the best option, but you need to reverse the rotation of the gearbox output shafts. This can be done with a crown wheel and pinion kit from scubygears in Australia, can't find an importer in Britain. I believe the kit costs around £1000+. Others have turned gearboxes upside down to reverse the output shafts, I read somewhere that this was not an option with the scuby gearbox. Therefore I have opted for the cheaper option to fabricate an adapter plate. If funds become available I would like to buy the conversion kit.
Ralph
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on September 28, 2014, 07:37:07 PM
See below website for the crownwheel and pinion conversion kits

http://www.subarugears.com/Pricing/Pricing.html

Ralph
Title: Re: Scuby 1800cc install
Post by: dom.kellett on September 28, 2014, 10:08:03 PM
Ahh, I'll probably go for the same idea as you then lol


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on October 17, 2014, 09:52:23 PM
Hi all, just received a scuby starter, second hand from ebay, and it works.  The problem now is the dog gear is the wrong pitch.  I am now trying to graft the dog126 drive clutch onto the scuby.  An alternative is to fit the scuby flywheel and try to find a friction plate with a similar diameter that fits the 126 spline or fit the scuby ring gear to the 126 flywheel.
Ralph
Title: Re: Scuby 1800cc install
Post by: dom.kellett on October 17, 2014, 10:12:35 PM
Wouldn't you be able to use the 126 fly wheel with scooby starter?


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: dom.kellett on October 17, 2014, 10:13:13 PM
Or, take the 'dog gear' off the 126 starter and fit that to the scooby motor some how maybe?


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on October 18, 2014, 09:08:34 PM
Dom the pitch of the ring gear on the scuby is greater than the 126.  I have looked at grafting the dog gear from the 126 to the scuby but will need to check the clutch mechanism to see if this is possible, even if it is possible I will have to reduce the diameter of the armature shaft to suit the 126. I suppose the ring gear from the scuby could be fitted to the 126 flywheel by shrinking on a steel ring to suit the scuby ring gear. So might take a bit longer to complete the first stage of the conversion.
Ralph
Title: Re: Scuby 1800cc install
Post by: dom.kellett on October 18, 2014, 11:51:01 PM
Ahh right I understand now, doesn't anywhere produce one? Or one from another car maybe? Save you having to manufacture one yourself?


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on October 19, 2014, 11:29:13 AM
When I contacted Scars they said the kit would cost £2000 plus and they would need the car and scuby engine and part of the kit was a specially built starter. I also tried to make contact with Alistair down in OZ, he has build photos on Nigels 'Retro 500 site' but he has not divulged what started motor he eventually adopted, he also tried the 126 starter and found it not powerful enough to turn the scuby. The search goes on when I resolve the problem I will post how and what I used.
Ralph
Title: Re: Scuby 1800cc install
Post by: dom.kellett on October 19, 2014, 01:51:29 PM
Ahh right, I understand the issue now, hope to see this thread continue though, should be doing the same with mine once I've got the engine, is yours the turbo 1.8?


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on October 19, 2014, 06:21:38 PM
It is the 1.8 out of the pickup, normally aspirated EA81.
Ralph
Title: Re: Scuby 1800cc install
Post by: dom.kellett on October 19, 2014, 09:58:24 PM
Ahh right, I'm going to be going for the 1.8 turbo or 2.0 turbo from an Impreza or wagon hopefully :)


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on November 01, 2014, 08:08:14 PM
Just spent all morning at a starter motor specialist, very helpful guy, he went back and forth looking for starters to try against my flywheel. Found a vw starter hot of a polo that meshed OK but it would be difficult to fit, large sections of the bell housing would have to be removed and special adapter and distance pieces made.  Eventually we found a starter from an old rover 820 auto, I was told it was an anti clock starter Iwill check it all out tomorrow.
Ralph
Title: Re: Scuby 1800cc install
Post by: dom.kellett on November 01, 2014, 08:10:25 PM
I'll keep that one in mind then mate, keep us informed as you carry on progressing! Very interesting :)


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on November 17, 2014, 01:16:33 PM
Finally found a starter which fits the 126 flywheel and is anti clock.  It is out of a VW 1.9 diesel, all I have to do now is fab an adapter/distance plate to get it to fit. I think it will be around 40mm thick as the mounting flange on the VW starter is further away from the pinion gear, which is the exposed -sticking out of the starter type opposed to the enclosed 126 style. Once I have it installed I will post some photos.

Ralph
Title: Re: Scuby 1800cc install
Post by: dom.kellett on November 17, 2014, 04:53:48 PM
Ooh great news mate! So glad this is going well for you! I did purchase a 2.0 turbo Sri engine from the saloon rally spec subaru but unfortunately I needed money to get my current transport on the road and had to sell it again (with profit of course), I'm not pondering over a gsx1400 engine with a turbo or r1 engine........ Or of course the illustrious subaru monster :)


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on December 16, 2014, 02:02:48 PM
I need to fab a 40mm thick distance/adapter to accommodate the new starter. I have had the hole machined in the centre of the 40mm thick aluminium to allow spotting the starter mounting holes. Getting closer to starting the beast might have a go over the festive hols. I ordered a pilot bearing from Germany part cost 8E postage cost 12e I wonder why rip-off, see photos
Title: Re: Scuby 1800cc install
Post by: dom.kellett on December 16, 2014, 08:13:02 PM
Lol, love the packaging! Have you edged the engine up to your car? So you think the 2.0 would fit or would you advise the 1.8 would be the safest option? What clutch are you going to be using also? Do you think the 126 gearbox will be able to withstand the power from the 1.8? Might strain it too much maybe?


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: dom.kellett on December 16, 2014, 08:13:11 PM
Oh and living the thread ;)


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: dom.kellett on December 16, 2014, 08:26:02 PM
One more question ;) did you try reversing the gearbox and using the original scooby gearbox? Could go awd! ;) just a few thoughts 😜


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on December 16, 2014, 09:17:29 PM
Hi, I read somewhere that inverting the scuby gearbox doesn't work, don't know why and don't have a gearbox to try it out.  I am using a panda/uno clutch, it has stronger springs to aid transfer of power.  There are a few 500's and 126's with 1800cc scubys, Z cars have fitted an 1800 and 2000 in 500's see link.  The 2ltr is slightly wider because it's overhead cams which takes up a bit more room.

Ralph

If you go to Z cars Facebook date 21st June 2013 you will see a 500 barcheta with a scuby 1800cc


https://m.facebook.com/ZcarsPerformance/photos/pcb.781515941878474/781515705211831/?type=1&source=49&refid=17
Title: Re: Scuby 1800cc install
Post by: dom.kellett on December 17, 2014, 10:07:06 PM
Ahh right thankyou :) I'll be buying a fully scooby, taking the engine, gearbox and wiring loom and then selling the rest for parts so I'll have a gearbox to try and play around with lol, thanks for the help mate :) keep the thread up! :)
Dom


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on January 05, 2015, 01:03:52 PM
Hi all just received the latest machined/amended parts thought the cost was a bit steep though.  Hope to have the engine started soon, once I machine the aluminium distance piece to fit. The distance piece had the hole machined, the flywheel had the bolt head area machined flat and the Boss had the wrong pilot bearing replaced with the correct one.

Ralph
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on April 10, 2015, 11:29:02 PM
How time flies anyway I managed to get into the starter adapter this week. So I have drilled and tapped holes for bolting to the Fiat bell housing and attaching the new starter.  I spent a few hours cutting the adapter out of the billet aluminium. See photos, next trial fit to establish area of bell housing to be removed then polish up to finish.
Ralph

Sorry for the double post
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on April 12, 2015, 04:34:30 PM
Amended the bell housing for the starter adapter, now need to clean and trial fit all to engine and see if it fires up.

Ralph
Title: Re: Scuby 1800cc install
Post by: Dom.kelltt on April 12, 2015, 08:28:26 PM
Looking great and also great quality of craftsmanship! Keep us posted :)


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on April 19, 2015, 11:28:50 AM
Things are moving on at pace, well for me anyway, finally managed to get the engine and gearbox and starter fitted together after some minor fettling for bolt head clearance. Removed the plugs skooshed some oil down the bores, connected the battery and pressed the button, she turned  :P :P :P :P. There was a sign of sludge from bore 1, did the oil down the bores another three times and it seemed to clear up, checked the compression and it seemed fine.  I will have to sort out the electronic ignition and a temporary fuel supply and see if she will fire up.
Ralph
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on April 19, 2015, 11:31:34 AM
Some photos

Ralph
Title: Re: Scuby 1800cc install
Post by: Dom.kelltt on April 19, 2015, 12:08:01 PM
It's looking great! Love your engineering skills and how neat and tidy all the work you do it! Are you going to adapt the original gearbox to put the power down or at least help it live a little longer?


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on April 19, 2015, 03:04:08 PM
I will inspect All gearbox internals to ensure they are in good condition, replace if required and hope for the best.
Ralph
Title: Re: Scuby 1800cc install
Post by: Dom.kelltt on April 19, 2015, 11:12:09 PM
Ahh right ok then,
Brilliant work though! Can't wait until this project is done so I can see if it's worth me trying my hand at the fabrication you have done :)
Great thread and keep it up!
thanks Dom


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on April 26, 2015, 06:56:32 PM
I had a major problem in finding someone who could supply an ignition coil to the correct primary and secondary resistance specified in the manual. Took a punt and emailed acuspark and the tested some coils and one fell into the mid range specified in the manual and it only cost £12, should arrive Wednesday. So hopefully I will fire it up next weekend.
Ralph
Title: Re: Scuby 1800cc install
Post by: Dom.kelltt on April 26, 2015, 08:57:54 PM
Great news! I've been offered a 2.0ltre turbo for 100 (with a few minor issues) and then I'm planning on using a 944 box in order to reduce the amount of gearboxes I shall tear through


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on April 27, 2015, 12:43:19 PM
944 box sounds interesting, I assume it's standard adapter plate as used on the beetle Subaru conversions.

Ralph
Title: Re: Scuby 1800cc install
Post by: Dom.kelltt on April 27, 2015, 03:44:41 PM
Yup, that's exactly what I'm thinking, just sort or copy what they do but incorporate the attempt to shorten everything (126's are tiny compared) lol

Also, I know I've asked you loads of questions but I have one more if that's ok,

How are you planning on mounting it into the car? But the same method as original engine or by making an adapter plate to lock it to the car??

Thanks Dom


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on May 02, 2015, 06:16:59 PM
Dom, I intend to adopt the same support system Alistair used on his conversion. I will see if I can post a link. I finally managed to fire her up, she lives. Only problem one cylinder has only50 while the others have 210 when I did the compression test. Anyway it all seems to next is the trial fit to finalise position of rediator and exhaust.
Ralph
Title: Re: Scuby 1800cc install
Post by: Dom.kelltt on May 02, 2015, 06:31:45 PM
Great news! Yeah if you could try upload some images that would be great! 😏 should be getting an engine tonight or tomorrow just need to go pick it up now that's all :) getting very excited lol

Glad to hear she lives and runs! Bet your chuffed with it right now! :)


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on May 02, 2015, 06:49:07 PM
The web site is www.retro500.com  go to engine swap gallery and then to Alistairs Subaru 1800.
Ralph
Title: Re: Scuby 1800cc install
Post by: Dom.kelltt on May 03, 2015, 12:21:54 AM
Perfect Thankyou :) should be picking up my block tomorrow :)
Dom


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: Dom.kelltt on May 03, 2015, 12:27:19 AM
Quite a good idea he has used there :) I'll definitely go for that one, looks strong, sterdy and reliable :) Thankyou for that like Ralph :) hope your conversion is complete and running soon!

Dom


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on May 03, 2015, 10:09:07 AM
I am finding it difficult to locate an engine gasket set, can get it from Australia or America but at a price, the ej engine might have been the best option as spares are abundant. I will continue with the trial fit and see how much work is required to fix the compression issue. I may have to change to an ej if the bore in mine is done.
Can't wait to see your progress photos.
Ralph
Title: Re: Scuby 1800cc install
Post by: Dom.kelltt on May 03, 2015, 03:28:39 PM
Ah sounds like a tricky situation then,
Hope you manage to source one soon!
Should be picking the engine up soon so fingers crossed lol


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on May 09, 2015, 08:25:55 AM
Latest update, tried everywhere to get a gasket set but to no avail, one of the engine machine shops said I would have to supply the block + oversize pistons and rings if I wanted a re-bore, another said he couldn't find anything listed for this engine. So I am now weighing up the cost of importing what I need to fix the engine against buying an ej20, so if you are thinking on a Subaru replacement engine I would not go for the ae81 or 82.
Ralph
Title: Re: Scuby 1800cc install
Post by: Dom.kelltt on May 09, 2015, 10:07:27 AM
Oh, sorry to hear about no luck Ralph, keep looking! There will be one tucked away somewhere! Got my ej20 sat at home now, beginning the proper strip down tonight to replace bits as I go along as it was only £100 because it needs new bottom end bearings, also the guy threw in a nice shiny new Sti inlet! Very pleased with my purchasement for now :), hope you find your parts soon! :)


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on May 10, 2015, 06:01:10 PM
Removed the head and found corrosion on the wall of the cylinder, not sure how fatal it is.  Used 400,800 and 1200 paper with light oil to remove the corrosion but I can still feel an irregularity in the smooth surface. Ordered up a full gasket set from over the pond should be here by the end of the month, I hope. It took nearly an hour to release the head from the block due to corrosion crud on one of the head studs, top left stud you can see the amount of crud still there, so I believe the head gasket had gone causing the problem. Therefore I have decided to restore the engine, so the strip down in serious begins plus the search for oversized pistons-rings? Photos show corrosion on cylinder wall dark areas. ::) ::) ::)

Ralph
Title: Re: Scuby 1800cc install
Post by: Dom.kelltt on May 10, 2015, 09:57:25 PM
Oooh dear, I'm beginning the strip down of my engine, however my GCSE exams start Tuesday so I'm calling it off until I've got them out of the way, may need 2 new heads sadly 😭 that's still to be checked,

Dom


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on May 10, 2015, 10:35:11 PM
Dom, sorry about the heads, it's a popular engine so if you need parts it should be easy enough to source. Best of luck with the exams, hear from you soon.
Ralph
Title: Re: Scuby 1800cc install
Post by: Dom.kelltt on May 10, 2015, 11:30:16 PM
It was a sad moment when I had to admit it may be best to source new ones, however, the person I bought this engine from has loads so going to see if I can get one at a knock down price lol,
Thankyou for the good luck to mate :) all should be fine, revision is more important than the car (as my parents keep insisting) so finally subsided lol,

As soon as I get a break in them I'll be using it to relieve all stress so shouldn't be too long lol,

Hope your build goes well here on out! :)

Dom


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: ronb1967 on May 19, 2015, 01:22:24 AM
Any one know what mph the 126 gearbox will go up to on standard sized tyres once its got its new engine fitted ?
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on May 19, 2015, 01:08:28 PM
The 126 engine in stock form can rev to 4700 ish with 24hp, while the Subaru can rev to 5200 with 75hp @ 4800rpm therefore if using standard wheels and tyres it will go a bit faster, not worked out the difference, it will also get there more quickly and be able to cruise at higher speeds more easily.  If you want to go faster fit larger wheels and tyres, need to take care as the increased torque required to move the car will put strain on the drivetrain so it is a balancing act.

Ralph
Title: Re: Scuby 1800cc install
Post by: ronb1967 on May 19, 2015, 04:12:33 PM
i know my 126 isn't the best at cornering in the wet and thats on a pair of pirelli 165's, the difference in engine weights will make the front end even lighter don' t you think (a bag of ready mix under bonnet :D)
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on May 19, 2015, 09:58:11 PM
I don't know the difference in engine weight, but the Subaru ea81 engine doesn't weigh that much more than the 126 lump as the Subaru unit is all alloy so I don't think it will make any difference to the handling. Hope to prove this theory later this year.

Ralph
Title: Re: Scuby 1800cc install
Post by: Dom.kelltt on May 19, 2015, 10:32:14 PM
Ralph, speak for yourself lol.
My Subaru engine weighs a b#*%+%d lot! I could quite easily carry the original round but not the Subaru one, it's a two man job and even then it's a struggle!

good luck with it though :)

Dom


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on May 20, 2015, 08:31:51 PM
Dom, the ej series engines start at 120kg, the ea81 only weighs 80kg  :P :P :P. I have just bought a replacement ea81 should arrive next week.

Ralph
Title: Re: Scuby 1800cc install
Post by: Dom.kelltt on May 20, 2015, 11:00:53 PM
Good news! Bad news for the weight of mine though 😂 oh well, i shall do this! Eventually......lol

Good luck with the replacement!

Dom


Sent from my iPhone using Tapatalk
Title: Re: Scuby 1800cc install
Post by: thepuddlejumper on May 27, 2015, 09:41:32 PM
Just recieved delivery of my replacement ea81 engine. I am assured it is a good strong engine, looks good with all ancillaries in place. Hope to progress work soon.
Ralph
Title: Re: Scuby 1800cc install
Post by: Dom.kelltt on May 28, 2015, 12:10:01 PM
Great to hear! Bought myself a td05 turbo yesterday, finally starting to get somewhere lol, hope all goes well :)


Sent from my iPhone using Tapatalk