Club126UK

Fiat 126 Chat => Tuning & Customising 126 Models => Topic started by: Alfons1972 on December 27, 2011, 08:18:37 AM

Title: paint-can-Tuning ;-)
Post by: Alfons1972 on December 27, 2011, 08:18:37 AM
Hello,
I want to tell you about a modification with which we have good results here in germany:

Here in Germany many Fiat 126 and 500 are using the "Farbdosen-Tuning".
First time (as far as I know) in 2002 a member of the german 500forum.de used a "Farbdose" (=paint can) of the Revell-paint-company. So you can call it "paint-can-tuning".
look at this:
http://www.500forum.de/wbboard/thread.php?threadid=326&boardid=11&sid=83b218cb8cb86641f4bcf0b3856692af&page=3
(I hope, you understand that).
pics:
http://www.500web.de/bilder/lowcost1.jpg
http://www.500web.de/bilder/lowcost2.jpg
http://www.500web.de/bilder/lowcost3.jpg
http://www.500web.de/bilder/lowcost4.jpg

I'll try to explain:
The problem on the 650ccm engines is the Mickey-Mouse-shaped bakelite spacer below the carb. It leads to turbulences in the gas-flow.
To avoid them, the inlet duct has to be "cleaned".
I use a different solution, made by a friend of me. Look on picture below.

Later, a member of the 500forum made that to a piece of art using a tube made of brass...:
http://fstatic1.mtb-news.de/img/photos/1/0/2/0/0/1/_/large/DSC06058.jpg
http://fstatic1.mtb-news.de/img/photos/1/0/2/0/0/1/_/large/DSC06059.jpg

that doesn't make your car much faster (just a little bit), but you will feel faster reaction of the engine, especially in low revs... Some drivers report a lower consumption of gasoline...
Title: Re: paint-can-Tuning ;-)
Post by: DEYAN IYI on December 27, 2011, 09:19:30 AM
Great solution!!!! 8)

Do you use smaller nuts and washers on the studs or there is enough room to get 28mm inner diameter? Or you cut a bit the washer?
Title: Re: paint-can-Tuning ;-)
Post by: Alfons1972 on December 27, 2011, 12:13:49 PM
yes, I use smaller nuts. And the washer had to be cut a little bit.
But all in all no problem...

someone of the Fiat-126-forum.de made about 20 pieces of those to sell them in the 126-forum.
they are all sold now but propably someone in the UK can do that, too?

here is a pic of my parts (not as nice, but great working...)
Title: Re: paint-can-Tuning ;-)
Post by: nrg19uk on December 27, 2011, 12:19:19 PM
Looks like a good idea?, I always understood that the rougher the surface of the inlet way
 Would be better to help with the atomisation of fuel and air mixture on the other hand have the outlet as clean as possible to stop resistance of air flow. That bakerlite piece is designed to create turbulances for better atomisation.

I'm sure someone could correct me.
Title: Re: paint-can-Tuning ;-)
Post by: smallcox on December 27, 2011, 02:33:59 PM
Alfrons1972,

I'am with you on this one,
I done this modifaction myself back in the 90's so I could fit a custum fit manifold to the cyclinder head but ditch the plastic spacer/manifold and replaced it with a aluminum one that accomplished the same job as you mentioned with the insert. I found that the original washers can be used just need to be grinded down on one side and the same nuts are used with no problems.(see photo) these pictures are on stripdown so the gaskets are damaged but gives you the idea. As for extra power Well it's got to be in the right direction and fuel comsumption will only drop if the port is opened out which I supposed is a common thing when you have a grinder in your hand. :$
I believe with the correct mods to the head this mod will give the same power outputs than a twin inlet port panda head with simular porting work due to this being a tidier inlet port when finished :)
Title: Re: paint-can-Tuning ;-)
Post by: nrg19uk on December 27, 2011, 05:23:58 PM
Im all for modifying the ports but There's no mention of them opening up there port? Just installing a liner to whats there. Decreasing port size+less atomisation= performance gains???
Title: Re: paint-can-Tuning ;-)
Post by: Rusty's Uncle on December 27, 2011, 09:09:30 PM
Great thread kicking off here and it is all about ideas that I was thinking about this year but never got to try out . No time to chat now but if your cordless electric kettle has blown don't chuck it out just yet, all will be revealed  :o
Title: Re: paint-can-Tuning ;-)
Post by: Hazey-n-Marc on December 27, 2011, 09:14:47 PM
Threw mine out last week. Crap!!
Title: Re: paint-can-Tuning ;-)
Post by: bis13 on December 27, 2011, 09:50:10 PM
hey rusty you ain t going to convert an aircooled into a water boiler?
Title: Re: paint-can-Tuning ;-)
Post by: Rusty's Uncle on December 28, 2011, 04:22:50 PM
No nothing like that but I will show you a picture of my bottom  ;D
The bottom of my kettle that is !
So I had been looking at porting heads and gas flows etc and thought that the aircooled inlet was not a good design in that department but hey it was designed over 50 years ago for very different environment. A sleeve to blank off the side pockets seemed to be the answer to eliminating turbulence on the inlet manifold but if it was too thick on the sidewall it would restrict the inlet but if it was thin & weak then it might collapse down into the inlet port & then into the cylinders.
I started looking on the internet for suitable tubes then came across a vacuum cleaner pipe which was just about right so set that aside for future experimentation.
So out of the blue my fairly new expensive DUALIT kettle packed up as did our very expensive DUALIT toaster. That is an aside but if you happen to google broken DUALIT items you wil find that there are masses of unhappy people out there about these items. I found that out after I stripped down the kettle to replace the element but you can't  >:( So I stripped the kettle down to its component parts to recycle them and the outer ring on the base contact is a great item for this inlet manifold job. I will get more pics when I can dig them out  :)
Title: Re: paint-can-Tuning ;-)
Post by: Alfons1972 on December 28, 2011, 06:21:09 PM
the tube I use was made by a friend of mine on a lathe in a few minutes...
The sidewalls are quite thin. I think, less than 1mm...
And those paint-cans are even thinner.

what is the trick is... (I do not know how to say it in english. Ok, I'll try).
ok, the trick is, that this tube has to have a wider top ending, so it cannot fall into the port. besides it stabilizes the tube a little more...

the next thing is that we make the tubes about 1mm shorter than the bakelite's height.
First, there will be no problems when mounting the carb if the gasket will be pressed when tightening the screws of the carb.
And second, there will be no additional transportation of heat from the head to the carb.
that 1mm gap does not influence the gas flow too much, the gap is simply too narrow...

look on my simple drawing below to understand what I mean.
Title: Re: paint-can-Tuning ;-)
Post by: Rusty's Uncle on December 28, 2011, 09:05:51 PM
Alfons , my friend you do not have to worry about your use of the English language  :)
I can only count up to about 5 in German but your correct use of "to" and "too" in the right context would put some over here to shame.
Anyway back to the main subject, the part I mention from a kettle has a tiny flange which will hold it in place and is extremely thin but firm.
So the part I mentioned came from an expensive (crap) Dualit kettle but I then had two other kettles which leaked or packed up so I stripped those down as well . Interesting to find that the £8.50 cordless kettle from Tesco had exactly the same components as the Dualit but with a different frock  >:(
So the chances are that most cordless kettles that sit on a base unit have a secret built in aircooled tuning device  :o
Title: Re: paint-can-Tuning ;-)
Post by: bis13 on December 28, 2011, 10:39:25 PM
hoo woz u referin two abouut proppa granmar?
rusty have you now gone into the kettle scrap business? this is very interesting but but to add a bit of a curve ball into this thread has anyone noticed any performance gains when the weather is wet whilst driving the 126 because mine is definitely better in the wet than any other time by this i mean it picks up a lot quicker and feels more eager? i shall try this paint tin trick and see what occurs i might even dissect a dyson.....
Title: Re: paint-can-Tuning ;-)
Post by: Rusty's Uncle on December 29, 2011, 06:10:22 PM
Dug the bits out today so here is a picture of the brass ferrule from the base of a kettle . They are not long enough to run all the way through the spacer and only go half way so if you get two you can push one in from each side or use a bit of a tin can soldered in place to complete the tube. The brass is only about 0.2mms (0.008") thick but quite firm.
Title: Re: paint-can-Tuning ;-)
Post by: DEYAN IYI on December 30, 2011, 12:03:37 PM
Looks like a good idea?, I always understood that the rougher the surface of the inlet way
 Would be better to help with the atomisation of fuel and air mixture on the other hand have the outlet as clean as possible to stop resistance of air flow. That bakerlite piece is designed to create turbulances for better atomisation.

I'm sure someone could correct me.

The bakerlite piece of sh... was designed to save some brain effort of the italian engineers :$ And then 30 years Polish resistence tо make any rationalization. Actually it's all about money saving (to cut 1 new size nut and 1 washer and then put by 2 of them... hahaha), who cares about performance... (Just compare to the japanese k-cars of the 70's...)
Title: Re: paint-can-Tuning ;-)
Post by: nrg19uk on December 30, 2011, 11:25:33 PM

[/quote]

The bakerlite piece of sh... was designed to save some brain effort of the italian engineers :$ And then 30 years Polish resistence tо make any rationalization. Actually it's all about money saving (to cut 1 new size nut and 1 washer and then put by 2 of them... hahaha).


 ;D thats not really scientific is it lol i was waiting for someone to come up with a more logical answer lol

Back in the 70s-80s if those italian engineers had put a little effort in??

something like this maybe? lol

 (http://i122.photobucket.com/albums/o254/nrg19uk/tune.jpg)

Title: Re: paint-can-Tuning ;-)
Post by: DEYAN IYI on December 31, 2011, 01:33:26 AM
Well... it was kind of joke, but in reality the car manufacturers do think that if they save 1 quid for a car it will be 5 000 000 for such a amount of units :$ And when you make a cheep car ... plenty of compromises.

The "joke" about ricers... When in 1972 our beloved 126 come on world with 23hp on 4800rpm, Honda Z600 was making 36hp on 9000rpm... also out of 600cc, 2 cyl..  :$ Abarth 695 makes 38hp/5400rpm out of 700cc. Honda had also disc breaks, power breaking, 5 speed gearbox... The interior looks like s supercar...  :$ And in the end it was not only Honda.

No science in the bakelite "heart" or "Mickey mouse" (I like this German comparison), no atomization. Just "to be something there". In my opinion Soichiro Honda would rather prefer harakiri. "Rougher surface of the inlet" means not to be polished like the outlet. The mixture moves in waves in both directions and all the obstacles aren't good, also for the resonance in definite rpm (valid for the exhaust as well). That's why single port for a cylinder means better filling, cos they don't spoil their work each other. Even better one carb per cylinder - lower speed of air/fuel mixture means more power ("lower" in the context of the same amount of air passing trough different sized sections, for ex. two 28mm standard carbs over Panda 30 head will work on 2 times lower air speed and that's what the progressive 2x30mm Panda's carb makes when both throttles are opened). And more interesting are Variable length intake manifolds.

Kowalski's turbine is kind of science fiction :) Better put some proper carb with acceleration pump ::)

In one word, trust the paint-can-tuning ;D The Polish experience shows that a 20mm spacer beneath the carb improves the performance. It would be nice to combine em. :)
Title: Re: paint-can-Tuning ;-)
Post by: nrg19uk on January 01, 2012, 04:18:54 PM
I think something was lost in translation here. :-)




From what I understood is if you want performance buy a Honda  :P


Title: Re: paint-can-Tuning ;-)
Post by: eben80 on January 01, 2012, 07:13:03 PM
This is similar to the intake port modification on this page:
http://www.forzafiat500.com/articles/?sa=view;article=2

That's quite an interesting article.
Title: Re: paint-can-Tuning ;-)
Post by: Rusty's Uncle on January 03, 2012, 09:12:47 PM
Christmas must be over as the Easter eggs and hot cross buns are in the shops  :o
So time to get back to playing with the "toys"
But first nrg what is that item you showed there ?
Deyan is there any theory behind the 2 cms spacer under the carb ? Are you saying that a spacer as well as a sleeved bakelite manifold would be good ?
So found a bit of time to do a bit of kettleing, no not school kids in Oxford Street but those bits from an electric kettle  ;D
Grabbed the first bakelite carb mount I found in my garage. The inlet passage was not good as there was some moulding flashing as well as missalignment. Got to work with some files , sorted that then fitted the brass ferrules and soldered them together to form a complete tube with tiny flange at each end. So far so good  ;)
Title: Re: paint-can-Tuning ;-)
Post by: nrg19uk on January 03, 2012, 11:16:31 PM
happy new year all


(http://i122.photobucket.com/albums/o254/nrg19uk/fan.jpg)


rusty its a kowalski turbine it sits between the carb and the head like a sorta turbo, adding the effects of turbulence atomising fuel and air for a better clean burn.

there are sceptics out there that say they dont work, other people who have them fitted say they get better fuel economy, more power and a nice sound.


here is a website with a very user friendly explanation on intake and exhaust system tuning

grab a coffee first and enjoy


http://bmwmotorcycletech.info/InExTuning.htm

The part about intake tract length is worth thinking about.




Title: Re: paint-can-Tuning ;-)
Post by: messerschmitt owner on January 04, 2012, 07:08:12 AM
Interestingly, I once had about fifteen percent of the surviving Honda Z600s in my carport (yep, I had three of them) and can testify to their 9000rpm red line. With a little tuning it is possible to get 12000rpm  out of a Z engine. The engine is a much better design than the air cooled Fiat engine, but it came from motorcycle technology, where engines were higher revving but albeit less torquey.

My 1959 Berkeley B95 produced 45bhp as standard from its 692cc engine - it has a decent amount of low down grunt due in part to its heavy crank and flywheel. Tuning for 55bhp was standard but 65-70bhp could be achieved (as in my car) if a racing mechanic was allowed near it (in the case of mine, an Ecurie Ecosse racing mechanic).

My smart roadster (turbocharged) left the factory with about 80bhp - it now has closer to 115bhp with nothing more than a remap and a few changes to the induction.

Anything that smooths the airflow into the carb and inlet manifold is a good thing.
Title: Re: paint-can-Tuning ;-)
Post by: smallcox on January 04, 2012, 11:10:09 AM

Happy new year all,
 Alfrons you started an interesting debate.

nrg19uk I'am one off those sceptics who believe these devices are, well, not worth the there own weight but do agree in requiring fine atomisation but there are other ways off doinig this without putting a restriction in the air path on the induction system. Interesting artical thought about induction and exhaust which you refere to as "intake tract lenghts.
I always believed the carb bolted straight to the cyclinder head is a bit like your lawnmower set up, It works but not power or fuel advance just a means to get the engine to work along with the exhaust bolted with no real lenght to the pipes to tune the engine for economy/power/refiness. A goal length inlet manifold of 4 to 5 inches would benifit power a econemy in my opion to enhance any ramming effect that can be gained this would also help with atomising suspended fuel if port size was restricted to a resonable size.
The artical on cyclinder head modifying shows all the common mistakes that often happen with so called power heads.
Hey Rusty time for a cup of tea, but you got to rebuild you kettle first. lol :P



Title: Re: paint-can-Tuning ;-)
Post by: DEYAN IYI on January 04, 2012, 06:58:56 PM
Hi everybody and HNY!!! Many wishes for health, smiles and nice 126 moments!!! Hope to see ya in Zvolen!!! :P

nrg19uk, sorry for my poor english, sometimes it's hard to be "Apache" :$ I'll do my best ::)

Thanks for the nice article! And let me correct you - it doesn't need coffee, but a beer box to read and reread... :)

Rusty, not much to say about the theory after this article, but if you ask why exactly 20mm in our case, I got no answer. Maybe there is no more room in the engine bay :) The "sleeved manifold" is 101% better than the original Mikey mouse. With the spacer is maybe better and less possible to be worse. What is the profit out of it, only dyno could say or if there is sensitive change in performance. I would try it if I play with the original carbie.  

About the Kowalski turbine... People enjoying it are probably this kind of guys that would never say that have bought something worthless :P Some of them run 140km/h 8).

 First of all this monkey works against the nature of our engine! Each cylinder provokes own turbulence. They are symmetric, so it means that if the swirling flow in cyl.1 turns clockwise in cyl.2 will be anticlockwise. I am not really sure, but before the valve must be also a swirling flow. So, between the carb and the valves there are two small tornados twisting in opposite directions. Maybe I am wrong, but anyway, if we accept that there is no swirling flow, then this ventilator helps the flow of cyl.1 and spoils the flow of cyl.2, cos passing trough the valve must change its direction.

On second place the benefits are really doubtful, and instead of praying for some tailwind for the turbine, better work on decent carb an exhaust.

On third place the life of this small miracle is about 10k km, then is possible to break in pieces. That's why it got that tea strainer in the bottom.  ;D  http://www.126fan.pl/www/turbinka.htm

When we are still with BPS (bakelit piece of something) aka Mikey mouse ;D - another miracle that turns fuel in the tank 8)

Odparownik - something like "evaporator".

Here you can take a look, but it's only in Polish: http://www.odparownik.za.pl

(http://www.odparownik.za.pl/razem.JPG)

(http://www.126fan.pl/www/images/odparownik/odparo_2.jpg)


The fact that the author overlooked the problem that "paint-can-tuning" solves, makes me sceptic about it.

Kind regards!
Title: Re: paint-can-Tuning ;-)
Post by: dajwid on January 04, 2012, 08:15:16 PM
Mmmmm, it says the modified 'mickey' has been patented, tests in 2 very well known Polish magazines both reported the mod, worked.

I have asked for a price for postage to the Uk. Must be worth a look.


Title: Re: paint-can-Tuning ;-)
Post by: dajwid on January 05, 2012, 04:14:48 PM
The guy has sold out of the modded parts, (In fact seemed suprised there are 126 owners in the uk), I am waiting for reply about plans of his mod.

Title: Re: paint-can-Tuning ;-)
Post by: fightingtorque on January 06, 2012, 10:38:36 PM
just a few pence worth.....

That strainer you have in it will reduce airflow by a surprising amount.  As usual, I would refer you to David Vizard regarding the amount of flow lost by gauze filters.  Having said that, I also had to rebuild a 126 engine because something (a washer) went into one of the cylinders...........

On the single carb/ throttle body per cylinder versus a shared system, least restriction will tend to give highest peak power (= individual unit per cylinder) but when the systems are shared, you get some benefit from the inertia of the gas - when one cylinder stops drawing, the charge wants to keep going so has inertia as soon as the valve opens.  This definitely works on a 4 cylinder where there is always one cylinder on intake, and the result is improved torque in low and mid range.

On a two cylinder, you do not have an intake stroke always going on, so how much benefit you get, I don't know.   

We are working on some v-twin engines with a single throttle body and it is hard work because on a v-twin the cylces of the two cylinders are not symetrically opposed.  My impression is that it works ok on the parallel twin, although I haven't taken individual lambda measurements for each cylinder.

enough...............
Title: Re: paint-can-Tuning ;-)
Post by: Funkin Go-nut on January 20, 2012, 05:11:22 PM
While I was stripping everything down after my breakdown (see other thread)

I thought I would try this MOD.

I had an old model paint tin and the first problem I had was that it was reasonably difficult to cut it to size without damaging the tin, after a bit of searching I found an exact same width pice of tube and after measuring the bakelite spacer cut it to length with a hacksaw.

After cleaning off the sharp edges i discovered that the tube (even the paint pot) is actually too large for the hole, so I got some sand paper and wrapped it round a socket extension bar and used my home made round file to widen the hole. ( I kept frequently checking to make sure that the metal tube was a tight fit).

After sanding and fitting I then discovered that the tube wont fit if the head bolts are not at the right angle, so I tightened these the smallest of turns so the flat edges of the Nuts allowed the tube to fit.

Rather than replacing the washers I cut slots in the tube to fit over them so that it all now sits snug and tight. (this also ensures that the tube cannot drop down into the inlet)

This isn't a straight forward drop in and fit mod, it does need some fettling.

The result (when she runs) is a definite improvement with more noticible pull/low down torque, its not massive but its deffinitly there (as the say every littlie helps)

So if you are thinking of trying this mod the agro is probbably worth it...

Hope this helps someone...

 :)
Title: Re: paint-can-Tuning ;-)
Post by: Alfons1972 on January 24, 2012, 09:19:17 PM
yes, that sounds good!
Title: Re: paint-can-Tuning ;-)
Post by: ape20ff on July 18, 2015, 08:49:08 PM
Hello.
I think that's the same idea.

(http://s27.postimg.org/5cz470uwv/image.jpg) (http://postimg.org/image/5cz470uwv/)

Bye.