Club126UK

Fiat 126 Chat => Fiat 126 Chat => Topic started by: eben80 on June 30, 2011, 07:16:37 AM

Title: E-bay Electronic Ignition Module
Post by: eben80 on June 30, 2011, 07:16:37 AM
Hi all,

Anyone else using one of these?
http://cgi.ebay.co.uk/Fiat-126-distributor-Electronic-Ignition-Ultra-Spark-/350439087489

I bought it before I bought the car  :o
I fitted it and it seems to work quite well...  Did one fail on anyone yet?
Of course I carry a mechanical spare just in case...
Title: Re: E-bay Electronic Ignition Module
Post by: Darrell on June 30, 2011, 08:46:45 AM
I've been using one for about a month now and it works very well indeed :-X
Title: Re: E-bay Electronic Ignition Module
Post by: eben80 on June 30, 2011, 08:49:25 AM
Lol so we're in the same boat...   ;D
Well here's to reliablility  :thumbup .....
Only problem I had with it is the pooty grommet it came with... did you replace yours?
Title: Re: E-bay Electronic Ignition Module
Post by: Darrell on June 30, 2011, 09:06:46 AM
I had a spare plastic bit, you know the one that connects the wires and the points spring to. So I made the hole a little bigger, and sealed the wires in place with some exoxy glue.

I am finding it to be way better than the electronic ignition I had before. The one I had before was pre-programmed, I think the programmer must have had a heavy night before prgramming mine :cry:
Title: Re: E-bay Electronic Ignition Module
Post by: eben80 on June 30, 2011, 09:09:59 AM
I might have to look for a spare plastic bit then.
What kind of unit did you have before?
While I was looking for a unit I only found 123 and another German version...

PS: Are you the only African in the village? Where from?  :)
Title: Re: E-bay Electronic Ignition Module
Post by: Darrell on June 30, 2011, 09:46:01 AM
I'm from a little tin pot country called Zimbabwe. Mostly unheard of and lead by a jolly good fellow the world loves. It was there in my youth I owned a 500 and a 500 giardiniera and that started me on fiats :)

Yes the 123 ignition was what I had before. I am annoyed with it as I paid alot of money for it.
It took me a while to realise it was the cause of many of my overheating problems so I guess warrenty has long run-out so probably will get no help from them.
Title: Re: E-bay Electronic Ignition Module
Post by: eben80 on June 30, 2011, 09:52:51 AM
Ah so you were my northern neighbor :D

Yes the 123 does seem to be a sledgehammer for a nut :)

When I installed the module I did have to turn the dizzy quite a bit though... to get the timing right again... I would have thought it would stay more of less the same.
Title: Re: E-bay Electronic Ignition Module
Post by: Darrell on June 30, 2011, 09:58:33 AM
Did you use a timing light?

Yes I found it a bit of a pickle to get the dizzy so the wires were roughly where I wanted them but I did a bit of hopping teeth and got there in the end.

Southern neighbour then...so I'm now not the only african in the village!! :$
Title: Re: E-bay Electronic Ignition Module
Post by: eben80 on June 30, 2011, 10:09:51 AM
Timing-light? WHat's that?  ;)

No all my tools got stolen just before I left London  :cry:

I still need to buy:
A socket-set
Torque wrench
Feeler gauge
bolt extractor
..what am I missing?

I installed it by cranking it with a pole on the starter switch while slowly turning the dizzy untill it started.
I then found the highest idle speed and just retarded it a little... seems to work ok....
Title: Re: E-bay Electronic Ignition Module
Post by: Darrell on June 30, 2011, 10:33:57 AM
I'd get a timing light.

They can be little sods these baby fiat engines. To get the best of the 26hp the timing has to be spot-on.
Title: Re: E-bay Electronic Ignition Module
Post by: eben80 on June 30, 2011, 11:28:52 AM
I'll keep that in mind thanks  :D
Title: Re: E-bay Electronic Ignition Module
Post by: Funkin Go-nut on July 20, 2011, 05:24:14 PM
Ive just bought one of these, does anyone have a pic of the module fitted?

I want to make sure i get it right as the only instructions are on the back of the blister pack it came in...

It doesn't seem a lot for £50 either.... :o

 :)

FGN
Title: Re: E-bay Electronic Ignition Module
Post by: Darrell on July 20, 2011, 07:58:16 PM
Instructions? It was so simple.
The module fits where the points were and the round thing slips over the lobed rotating bit.

Title: Re: E-bay Electronic Ignition Module
Post by: Funkin Go-nut on July 20, 2011, 11:08:59 PM
It almost looks too simple so I ended up feeling nervous, so I thought I would check with someone who had fitted one before I went ahead.... ;D
Title: Re: E-bay Electronic Ignition Module
Post by: Darrell on July 21, 2011, 09:33:00 AM
 ;D

They are rediculously simple. I recon for the price you getting pretty much what you pay for. I like the way they have tailored it to work with either a single or double chimney set-up on the coil.

The only part that I found a bit annoying was I didn't remember where the rotor was pointing when I took the dizzy out to fit it.

As a result I had to crank the engine and turn the dizzy till the engine fired, then fine tune the timing with a timing light.
50 quid versus the 200 or so for the other type of ignition...lets hope the simple things in life are the best  ;D
Title: Re: E-bay Electronic Ignition Module
Post by: jokke on July 21, 2011, 08:18:28 PM
is this for AC only, or will it fit BIS?
Title: Re: E-bay Electronic Ignition Module
Post by: smallcox on July 21, 2011, 09:16:30 PM
Just to jump on the band wagon, I got one to.

Found that when fitted to some dizzeys the ring was loose and not a tight fit. Managed to find a polish part and it was a snug fit on the shaft. As soon as I started the engine I noticed it run faster and better and had to turn the idle screw down on the carb. I think it's well priced and hope its going to last. Those more expensive kit you mentioned do have advantages but this simple system just replace the troubled points so I'am happy ;D
Title: Re: E-bay Electronic Ignition Module
Post by: Funkin Go-nut on July 22, 2011, 12:00:45 AM
I found that my ring was a bit loose ( :-X ), presumably this is the trigger as it rotates on the dizzy, is it important that this is held in place? Any suggestions as to how this could be done? (I did think of using araldite but i think it would melt as it seems to get quite hot in there..)

I timed it up by hand and took it for a run and it seemed to pull better, but I still had some sputtering when it warmed up (a problem I already had..), I will time correctly as I bought a timing lamp today.

Some points with the one I got, the parts that stated they were black in the instructions were actually red, the leads to the coil were too short and I cut the plastic bung in teh dizzy side wall to hold the rubber gromet in place.

One other point is that the wires in the cap could move and rub on the spindle or catch the rota arm does anyone have a solution?

Other than that its fine.
Title: Re: E-bay Electronic Ignition Module
Post by: eben80 on July 22, 2011, 08:10:44 AM
My inductive ring fitted nicely luckily. I suppose a loose ring could either be a worn shaft or a ring with incorrect manufacturing tolerance(most likely the latter) :)
The loose wires can be remedied by modifying the plastic insert from a spare original points so that the wires fit in there snugly. As there is no snagging parts on the ring you should be ok as long as there is not too much slack...
Title: Re: E-bay Electronic Ignition Module
Post by: Funkin Go-nut on August 01, 2011, 06:16:33 PM
Ok a quick update.

The inductive ring was loose because it was not made correctly or was the wrong part, a have built up the edge using "chemical metal" as this should withstand the heat in the dizzy..it now fits snugly with no movement.

I used the original plastic insert as suggested and widened the hole, the wires now sit well out of the way of the rotor shaft.

Today I got around to checking the timing and it was a bit out (I had set it up by ear) a quick adjustment of the dizzy and all is now spot on.  :)

The car runs really well now, is quieter and pulls a lot better plus there is no sputtering under load  8)

I wish I had waited a couple of weeks before buying as they were selling the same kits at the Silverstone Classic for £23...  :(

Oh well on to the next job..
Title: Re: E-bay Electronic Ignition Module
Post by: robinoz on November 23, 2011, 07:35:23 AM
So whatare the options for a roterless distributor ??
Title: Re: E-bay Electronic Ignition Module
Post by: Amateb8 on November 23, 2011, 01:34:19 PM
This electronic ignition appear to be great. The participants of the discussion seem to be from 126 aircooled owners. Here is my stupid question. Presume this will also work well with the 126 Bis. Jokke did ask the question.
Title: Re: E-bay Electronic Ignition Module
Post by: Darrell on November 24, 2011, 09:35:15 AM
MIght need some lateral thinking and modification for the BIS.

I think the dizzy shaft bit is more-or less the same on the air cooler and boiler BIS.

The points on the boilers are bigger so how one would get around that I dunno, perhaps drill new holes in the plate to fit the pickup.

I have a boiler dizzy I will have a look at some time and report back.

My module thing hasnt missed a beat since installed ;D
Title: Re: E-bay Electronic Ignition Module
Post by: Tomasz on November 24, 2011, 01:38:16 PM
I wonder which is better - this one or the accuspark one:
 http://www.ebay.co.uk/itm/Fiat-126-AccuSpark-electronic-ignition-kit-/190569972829?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item2c5edb045d 
which is cheaper. Or maybe they are the same one! I think i may go for one of these when i have some spare money.
btw hello everyone, i have not posted in a while but i am using my 126p again now!
Title: Re: E-bay Electronic Ignition Module
Post by: Funkin Go-nut on November 24, 2011, 02:01:46 PM
Mine is still working fine as well  ;D

Tomasz, if you are in Norwich you can have a look at a fitted one if you like?
Title: Re: E-bay Electronic Ignition Module
Post by: Tomasz on November 24, 2011, 02:35:50 PM
I might take you up on that offer nearer the time. My sister in law said she saw a 126 the other day around Bracon Ash and thought it was me at first then noticed front fog lights. Could that have been you?!
I live around the Golden Triangle.
Title: Re: E-bay Electronic Ignition Module
Post by: Funkin Go-nut on November 28, 2011, 10:32:23 PM
Could have been, if the fogs were big and yellow, the 126 was white and it was driven by a big bloke with a greying beard :-)

I live just the other side of Taccolneston and work in Thorpe and use the 126 most days for work.

Title: Re: E-bay Electronic Ignition Module
Post by: Tomasz on November 29, 2011, 10:01:19 AM
Haha must have been you! Come to think of it, i think i saw you bombing along the Norwich road a while back.

(sorry to go off topic everyone)

back on topic: i think i might give the accuspark one a go after christmas.