Club126UK
Fiat 126 Chat => Fiat 126 Chat => Topic started by: nrg19uk on June 21, 2011, 09:48:50 PM
-
howdie folks ive been messing again :-) i kept getting the dreaded oil warning light come up once driving for a long time, so i changed the sensor made no diffrence, changed the oil, set timing made no diffrence starting to get a bit peed off i was scanning the net for aircooled tips so i turned my idle up etc still the same problem so i decided to buy a oil pressure and oil temp gauges, fitted those.
oil pressure on start up 75 psi once driving would drop to 50 then once got upto temp would drop to 40/25 depending how big the hill was.
the temperature got to about 125 and stayed steady
i searched the net searched the forum!!! banged my head against the wall and came up with two things either the crank bearing or the timing. :cry:
so i decided to tackle the timing first £50 later
new coil
new plugs + leads
new rotor
new condensor
new dizzy
and new points
set the timing and yippie ki-yay it only bloody runs sweet as a nut!!
oil pressure on start is 75 psi and drops to 60/55 psi
oil temp is sitting at 100o
picks up really well now starts first time :-) ive even over took someone!!! im over the moon ;D ;D ;D it even feels alot cooler in the engine room :P
-
Sounds a bit odd the high pressure to start with.
Mine stays pretty constant at 40psi hot cold or whatever. Remember there is a spring pressure release valve which is the bit that presses against the cam.
One thing is for certain, you have pressure and you are getting closer to solving the problem.
I did a daft thing when putting mine back together, proir to that the rear bearing had a big piece ripped out of it. I put it together and got the washer on the front end of the crank the wrong way and the oil light refused to play ball.
-
I think its quite normal for oil pressure to drop, as the engine warms the oil thins so flows more easily.
I'm confused how altering the ignition circuit can increase the oil pressure though?
-
I thought it was a bit strange but it makes sense when you think about. Oil gets warm and becomes thinner so to speak, my engine was running red hot there for piss thin! Lol
Well its running so much better I'm not sure if I'm getting a higher pressure on startup because the thickness of the oil I'm using the castrol classic stuff, It seems to have settled down to 75 psi and stays constant.
I seem to have developed a misfire every now and then. I've cleaned the fuel tank changed the lines and installed a see througth filter but when the engines running it barely fills the filter It doesn't look like enougth fuel coming througth, but if i take the feed from the fuel pump off it seems like it's gushing througth?????
Also I struggled to start her up the other day before strobe lighting the timing so I advanced the ignition a bit, my god the car was like a rocket, the problem was when I turned the ignition off it carried on running lol
-
ive been having a play this morning with my fuel pressure tester have a look and tell me what you think :o
http://s122.photobucket.com/albums/o254/nrg19uk/?action=view¤t=IMG_1177.mp4
-
Oi you all in the garden having a beer in this lovely weather
Spare some time and give me some feedback :P
Is this normal for the pump pressure to be so erratic? Or is
My pump is knackred?
What's the normal pressure? Should it be constant
Or
Doesn't it matter?
-
Hi!
Nice dance! ;D I don't know how normal it could be according to the fuel line back to the tank. You'd better check if the valves in the pump are working proper. Release the lines and blow in both directions. Watch out, cos usually is tasty, but not dangerous, we have it already in the blood :$
It must pump minimum 40dm3/h at 2000rpm.
14,7...24,5 kPa (0,15...0,25 kg/cm2) but no data about rpm, so have them like min&max.
The rod must come over the seal surface exactly 1,5mm (other source says 1...1,5mm and 2,4mm stroke), before it's pushed by the eccentric on the camshaft. If it's more or less, you can adjust it by fitting 0,3-0,7-1,2mm seal between the heat isolator and the block.
:thumbup
-
at a guess i dont think that is right, :D have you checked your pressure gauge on another vehicle..
Jumping pressure gauges usually indicate that the pressure is escaping, and then resealing. Pressure relief valve?
-
Thanks for that deyan/kipster I can't seem to see why it's doing it apart from
It's knackred.
I think I'm gonna invest in a electric fuel pump.
Has anybody fitted the cutoff kit to there's? I've read it's a requirement for retro fit fuel pumps also the solid state fuel pumps should be fitted level with fuel tank for correct flow???
-
I'd say that is about normal bahaviour.
Remember the pump is operating like a bicycle pump. There is a bypass that goes back to the tank to ensure there is always flow through the pump. This will also help keep the pressure up at higher fuel usage and keep the pressure down on low usage.
Then to throw a variable into the equation the float is opening the valve from time to time. I'd expect the pressure to jump about like a crazy thing.
I run an electric pump, fuel line pressure is more constant and there is less cranking to start the engine when the fuel in the bowl evaporates out. ::)
-
What pump are you guys running? You got any pics of your setup?
-
I think Dajwid had a topic of a fuel pump he bought, his pump is slightly different to mine however same principal.
I have a square shaped facet pump and the same regulator that Dajwid has.
-
Yea I have seen his I'm looking into something similar. have you blanked off the return from the carb? Does your pump stop once it's reached its pressure when it's full?
-
I did have a carb that did not feature the return, this was a problem as the regulator would every now and then not open.
A bit of experience with regulators tells me that once the bowl is full, the pressure will go up. The regulator reacts by closing-down. Now the regulator thinks there is too much pressure and stays shut.
I then changed to a Dellorto FZD which has a bypass fitted however there was no restriction as there is in the original Webber. At heavy load I was litterally running out of fuel as there was no/little flow into the fuel bowl.
I then machined-up a restrictor the same size as the one in the Webber and since then have never had a problem at all.
So in answer to the question yes bypass needed, no problem with original carb. Any other carb make sure there is a restriction going on the fuel line back to the tank.
I must add I am also very pleased with myself as mine is running sweet as a nut too ;D
With the original cam I could only make a maximum of 40 mph up a hill near my house. Now I can do nearly 50 with the new cam ;D
-
Nice I'll be over the moon with that! What camshaft is it? How much that set you back?
I've been looking at the facet fuel pumps
Off flea bay for about 20 notes but I've read they need a cut off kit?? Is that rubbish?
-
I bought mine off flea bay and all that happens is it is wired to the posative side of the coil, negative to earth, key on it comes-on, key off it goes off.
The cam I got for £200 from a 500 guy who was leaving the country, I'll dig-out the ticket he had on it but 40 was one of the numbers it had on it.
My only concern now is it seems to make alot more power at higher revs and that is when things start to rattle apart on my bug as I havn't had the time or resources to do the super dynamic balancing black magic on my crank etc which I think now is the next step.
Might cheat and get the crank out of the spare engine I bought done and then swap it over ;D
It's crazy how it'll go way past 60mph but things start to break past 60mph.
Maybe I should start a piggy bank for the 5th gear conversion..
-
Well i brought a electric full pump and glass filter went to fit it and my fuel hoses fitted on the 24th of this month have started breaking down! They are all squishey and sticky and the fuel filter is full off little blobs!!! >:(
So I've taken the hose back and changed it so I will change the fuel lines and pump later. Not happy ??? I've got to take the fuel tank off again.....
-
Bugger!
-
She's alive ;-) I got round to changing the fuel lines fitted the pump and she's purring like a cat :-) first try aswell!! Crapped myself thoe when I first started it, there was petrol everywhere I thought it was pissing out the carb but it was the remainder left in the mechanical pump lol :$
I went for a drive about 20 min sat at 60down the dual carriage way dropped slightly at a hill but
Nothing like before. Now All I get is a little mis/pop when slowing down on the gears and when sitting at ideal But I'm sure that's just down to tuning?
Ive left the Mech pump in place for the
Moment but I'm gonna remove that later, there was a bit of suction there but nothing to write
Home about.
Overall Im as happy as a pig in xxxx :P I dont know why I waited so long to change the pump...
-
;D ;D ;D ;D ;D
I found mine miss/pops when the points are about to close-up
Now it's on electronic ignition it seems to have completely gone.
Your starter is going to love that new pump ;)
-
sounds like my next investment ;D
-
I think a new carb maybe first I've blown the brass insert out on the return hose off the carb covering the whole engine bay in petrol :-( I've pushed it back in I hope it holds out for the return trip home.
Too much pressure from the pump or just unlucky?
-
Ah that happens, not the first nor second time I've heard of that.
I had a carb without one of those brass hose adaptors in, the one in an old fuel pump I had looked about the same so I warmed-up the pump (after stripping it down) and it popped-out. I then warmed-up the carb body and pushed it in, a few taps to be sure and it seems good.
Unfortunately changed that carb for a Dellorto FZD.
Keep an eye on it, did you instal a fuel pressure regulator?
-
No I was told it wasn't necessary by the company i brought it from as it has a return of the carb and such low pressure (2.5-3.0 off the top of my head)
I dont want tha happning again i was lucky the car didn't burst into flames there was loads of petrol everywhere by the time I had stopped in a safe place.
I've got some liquid metal you think that will hold it into place.
-
I'm not sure about liquid metal, maybe someone else can comment on that, I didn't use anything, just a bit of warmth from a hot air gun.
Not sure about the pump you have. maybe if the pressure doesn't go up too high it'll be ok?
I installed a regulator as a precaution and have to confess the FZD carb seems to prefer a specific pressure setting I'd have to walk to the car to tell you as cannot remember it off the top of my head.
Too little pressure it wouldn't keep-up with demand and too much raises the float bowl level.
You can check the float level with a piece of clear hose onto a fitting you screw into the drain (a bike trick)
In theory I guess at a max of 3psi you don't need a regulator. Sometimes I think 126's should have cameras fitted in the engine bay with a screen on the dash so as to see what is going on :)
-
Some Fiat models (don't ask which because I can't remember) used a Y type junction in the fuel line, the smaller part of which was a return line to the tank. This meant that a constant pressure was maintained at the carb and excess was returned to the tank.
-
ive given the tinkering on the engine a rest for a bit and i thought i would have a play with the dash and the electrics.
what do you think?
(http://i122.photobucket.com/albums/o254/nrg19uk/IMG_1185.jpg)
(http://i122.photobucket.com/albums/o254/nrg19uk/IMG_1184.jpg)
i cant imagine it would be everyones cuppa tea but i like it... :P
-
Mmmm, I like it, wouldn't do it in mine but looks clean. Great job!!
-
Looking so tidy and clean, job well done. :)
I don't like the padding on Bis dash so i consider similar (no)padding when i have a bis.
-
I'm glad someone likes it! If your going todo it don't use carpet glue like I did as it's lifted slightly with heat I would suggest a contact adhesive like Evo stick.