Club126UK

Fiat 126 Chat => Fiat 126 Chat => Topic started by: Amateb8 on February 28, 2011, 05:45:08 PM

Title: Headlining - Auto insulation/Sound deadening material
Post by: Amateb8 on February 28, 2011, 05:45:08 PM
My headlining is about to give up the ghost. The cloth headlining started to sag in other areas, so not now very presentable. Previously managed to prop it in place using balsa wood across the passenger and driver end but it has worsened. I intend to replace the headlining and sticking new cloth (or vinyl) covering onto the original board (not sure state of original board until I physically remove it) using adhesive spray.

Has anyone tried to install auto insulation/sound deadening/anti vibration material onto the roof area before installing/replacing the headlining? Googled some information on the type of materials available and the likes of Dynamat, Second Skin Audio Damplifier Pro came up. It has adhesive backing, so it is easy to install. It looks good but a bit pricey. I was wondering whether anyone has used on of these materials or something similar before.
Title: Re: Auto insulation/Sound deadening material
Post by: Darrell on February 28, 2011, 06:38:29 PM
I tried sticking foam to the roof.

When it got hot it all fell down :P

Thats the only concern I guess but dynomat is supposed to be the best [-/
Title: Re: Auto insulation/Sound deadening material
Post by: Pete126 on March 01, 2011, 07:06:16 PM
In the past i've used underseal :D just slap it on nice and thick and it stops allot of the drumming, its also very cheap [-/
I have also used it as a glue and stuck a good carpet under-felt under the bonnet of old cars, Works very well and never came off ;D   
Title: Re: Auto insulation/Sound deadening material
Post by: Amateb8 on March 12, 2011, 06:22:45 PM
Took my headlining off this afternoon. It was a struggle trying to get it out without damaging it and in one piece. I managed to pull about a fifth of the thing out from the rear hatch but it just would not budge further. Got my other half to push the lining from the inside outwards whilst I pull the board from the hatch, still would not budge. In the end, I had to force the thing out, damaging it, BUT it is still in one piece - salvageable. It was so difficult to remove, that I can not imagine putting it back on!

I will need to improvise as not sure I can reuse the original headlining board. I can use the old headlining board as a template. There was a thread using mdf (wrapping this with cloth or vinyl?) or using a piece of carpet. Any more ideas?
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: Amateb8 on March 13, 2011, 02:09:48 PM
What struck me was that there was no sound/vibration insulation underneath the headlining. The original headlining was relatively heavy as well.

I am thinking of installing the Dynamat Superlite sound dampening material rather than the original Damplifier Pro which is also very effective but allegedly quite heavy. I might use the Second Skin Audio Luxury Liner Pro on top of the Superlite but cover it up with felt fabric or something.
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: Darrell on March 13, 2011, 05:09:04 PM
Sounds good to be lightening the car  [-/
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: bis13 on March 13, 2011, 07:58:06 PM
go even lighter by ripping all the sound deadening stuff out and buying some earplugs.... ;D
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: Amateb8 on April 12, 2011, 11:28:34 PM
I found this foam-backed headlining fabric from ebay.

http://shop.ebay.co.uk/i.html?_nkw=foam+backed+headlining&_sacat=0&_dmpt=UK_CarsParts_Vehicles_CarParts_SM&_dmd=2&_odkw=headlining+fabric&_osacat=0&_trksid=p3286.c0.m270.l1313
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: paul555 on April 21, 2011, 07:14:11 PM
I'm thinking about something like this http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=110562026849&ssPageName=STRK:MEWAX:IT and it depends on thicknes might back it with some thin foam.
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: Amateb8 on April 30, 2011, 10:29:50 PM
I went to Brooklands today. I was a bit worried that without a headlining, the car would be like an oven given that the sun was going to be out in all its glory. Amazingly, the bare metal roof interior remained cold even when the car was parked all day in the glaring sun.
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: dajwid on May 01, 2011, 09:41:28 AM
Personally I have never bothered, always looked tatty so I have removed from every 126 I have had.
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: bis13 on May 01, 2011, 08:21:36 PM
my headlining is a haines manual for a 126.....
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: Amateb8 on July 03, 2011, 11:00:09 PM
My workplace is currently being refurbished and I found this discarded material. I am not sure what it is but it is the ideal backing for my headlining. It is flexible and easy to cut to size. Tried it on the car this afternoon and it fits perfectly.

I will go for Paul555's suggestion of using felt fabric. It has good sound insulating qualities and looks attractive. I will probably go for 3mm thickness in light grey or something.

Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: thepuddlejumper on July 04, 2011, 12:57:34 PM
Is that material used for fitting tiles to floors.

Ralph
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: chrisrhodesinlbz on July 05, 2011, 09:27:06 PM
Hello Forum members

This has been really useful for me, I have had my Bis for 3 years, but it came without any headlining at all (just a bare metal blue roof), so I never knew what I was missing!

I'm ordering the grey headlining stuff from ebay shown by Amateb8 to see what difference it makes! I'm hoping I can just use the spray adhesive and it will stay there forever (any hints on preparation gratefully recieved)

Thanks

Chris
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: Amateb8 on July 05, 2011, 10:14:39 PM
Hello. I intend to use adhesive spray to stick the felt fabric onto my orange backing (pictured). Once the adhesive is dry, I will then position the headlining in place before applying the adhesive to check whether it will be good enough to stop the "drumming" sound effect. If the drumming sound is still noticable, I will install the Dynamite Superlite sound deadening tiles before sticking on the headlining.

Chris, what headling backing will you use? A thin wooden board or something similar cut to size? I can send you a headlining template.
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: Amateb8 on July 10, 2011, 10:45:12 PM
I have been busy this afternoon. I started cutting the felt material to size and used adhesive spray to stick the felt fabric onto the orange backing. So far so good.
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: Amateb8 on July 16, 2011, 12:45:22 PM
It has been raining all morning and perhaps through the afternoon, so I thought of finishing off my headlining. I am pleased with the finish. It is better than I expected. It has the imprint of the orange backing, so not plain looking. I used the excess felting to cover the other side of the headlining, to enhance the sound proofing qualities of the material. I will try it again in the car with the felting installed to see whether it needs adjusting, when there is a lull in the rain.

Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: Pete126 on July 16, 2011, 05:36:32 PM
Cool 8)
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: nrg19uk on July 16, 2011, 05:42:10 PM
dont use normall spary glue as it will get hot and fall off

http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=270490429119&ssPageName=STRK:MEWAX:IT


or a contact adhesive
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: Amateb8 on July 17, 2011, 11:21:50 AM
Tried the finished product on for size to see whether it needed some adjustment - it did. Pulled the felt off on both sides (length) and added about a centimeter on either side. Did this to ensure the felt material went into the cavity above the door and rear window frames. By the way, the drumming noise has disappeared!

Tried it on for size again - perfect. The excess felt that I added slid into the cavity and in a way ensured that it stayed in place. This was possible because my orange backing was thinner than the original headlining board.

It may be a challenge to intall the headlining after spraying adhesive on both the bare metal roof and headlining as the headlining will stick on contact, so absolutely no room for adjustment. I must position the headlining correctly the first time.

Here are some photos of the headling before applying the adhesive. I think it looks better than my original headlining
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: Amateb8 on July 17, 2011, 11:30:44 AM
I bought one of those off the shelf contact adhesives in a spray can. I will see how it performs. I think it will be fine - hopefully. When I did not have a headlining, my roof remained cool to lukewarm even when parked under the sun in the height of summer.
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: nrg19uk on July 17, 2011, 02:23:22 PM
I thought that it would be fine with my dash, I now have to redo because its come unstuck!  :$
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: GTMaster on October 04, 2011, 12:20:26 PM
Thanks for the helpful thread. I've been trying to find a solution to making one for my own. I had one made using a wooden board (similar to the original) and carpet but upon fitting it broke as it wasn't flexible enough. This orange polyethylene looks like something that can bend well. Have to check and see where i can obtain some and of course the cost. I'll also have to look into what sort of glue would be most appropriate to use on the fabric...
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: GTMaster on October 04, 2011, 12:29:43 PM
3M photo mount looks like a good type as it's heat resistant...
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: ciaoflyer on October 04, 2011, 07:17:54 PM
I went to Brooklands today. I was a bit worried that without a headlining, the car would be like an oven given that the sun was going to be out in all its glory. Amazingly, the bare metal roof interior remained cold even when the car was parked all day in the glaring sun.

Light colours reflect the light so therefore will conduct little heat, if your car was black it would not reflect the light and get hot.
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: KAL SPL on October 05, 2011, 12:18:16 PM
You cant beat dynamat !
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: Amateb8 on October 05, 2011, 06:42:08 PM
I did not install the Dynamat but I am sure it will work brilliantly. I will probably use it on my other Bis. I stuck on the felt material on both sides of the orange plastic material. The felt material has sound proofing characteristics, so did not see the need for Dynamat.

Does anyone know what the orange plastic thing is called and where one can buy it?
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: GTMaster on October 05, 2011, 09:21:57 PM
It was mentioned by thepuddlejumper that it is used  for tile floors. I found this:

http://www.schluter.com/6_1_ditra.aspx
Title: Re: Headlining - Auto insulation/Sound deadening material
Post by: Amateb8 on October 05, 2011, 10:44:35 PM
Many thanks. I think that is the one! The link is the U.S. manufacturer's website. I have not seen this in the usual stores like Homebase. I'll try going to Wickes or similar.