Club126UK
Fiat 126 Chat => Fiat 126 Chat => Topic started by: nrg19uk on January 27, 2011, 12:20:41 PM
-
yipppiieeee finally got the aircooled back on the road!!! 8)
on the way to the test centre for the retest for the lights and the bit of welding i ended up hittting a pot hole the exhaust manifold decided to come away at the rear of the engine so i crept into the mot place without reving ;-)
whats the best way to fix it?
helicoil or rethread for bigger bolts? what size helicoil would i need
-
Congrats on the MOT , always a great moment ;D
Assuming the bolts holding the manifold elbow to the head have stripped then I would go for helicoils as if you go for bigger bolts there is no way back if & when they go . Also if you go for studs instead of bolts then you should not have to face the problem ever again. The thread size is M8 x 1.25 & I was quite amazed this week to see that you can get a thread repair complete kit on eBay for less than £20. I will take a pic of my set up & post it as there are other things you can do to make it all sound [-/
-
well i took the engine out to have a closer look at the leaky exhaust also to cure a leak from the rocker i can never seem to stop!!!
the exhaust is completly wrecked! im not even gonna bother welding it im just gonna go back to a standard pipe. whats more annoying is this was a new exhaust fitted last year and sat on the drive since!!! a maximum of ten mins use!!
(http://i122.photobucket.com/albums/o254/nrg19uk/IMG_0864.jpg)
cheers rusty im gonna purchase a heli kit asap theres someone selling a ss stud set on flea bay this any good or would normal steel be better?
aircooled over the pit at mot shop not much room for error!!
(http://i122.photobucket.com/albums/o254/nrg19uk/IMG_0859.jpg)
-
That exhaust looks poorly but at least you put a bandage on it before you put it out of its misery :oops:
I think that there are a number of guys on here that will see that exhaust and share your pain >:(
Seems you get what you pay for with exhausts & that exhaust box shape suggests it is one of the cheap imports that appear to be made of "potty putty" or something similar plus there are issues with the mounting brackets.
If you are going standard then the original shape & fittings work the best in my experience.
Looked at the stainless set on eBay , is that volksbolts? , could be a reasonable deal & you get twice as many as you need for a 126, studs seem to be studding (threaded all along) which should not be a problem & they have 100% rating.
My set up is steel studs into head with stainless flat spring washers & dome nuts, then stainless flat spring wahsers & stud connectors on the steel elbow studs backed up by a locking stainless grub screw into the stud connectors. So you have all stainless on the exposed bits & the steel protected from the elements. Posting a pic but ignore the bit of "bandage" and the clip. It got damaged and the exhaust wrap disintedrated at the same time as I had the oil leak so my engine bay is pretty much coated in fur. Also you can see that high temp paint is pretty rubbish afterb about 6 months :o
-
Yea that's the guy, whilst on eBay I brought the helical kit aswell as a new rocker cover gasket.
I paid 100 quid from that Chet guy off eBay for that exhaust not the cheapest out there And as you say looks like it's made of old fords ;-) it snapped of completely above the weld I don't think the brackets where a problem as it was solid. But I'm missing the bolts out of the block.
I may get a stainless one made at a later date if I'm feeling rich one month and do away with the manifolds if you can.
That's a tidy looking setup you have there! The paint has gone the same on mine there's a heat paint I was looking into that you cook painted like a cheAp powder coating system just another wild thought.
-
Now exhausts is what I`ve experimented on:The best and only way is to get the exhaust either new or good condition,take it to a shot blasting man,get him or her to blast it then hot flame sprayed then you can paint it what ever colour you like.My exhausts have lasted more than 7 years.Dont waste your hard earned cash on simply spraying a new exhaust IT COMES OFF AFTER 2 or 3 OR THREE "burns"
-
good on ya neil you can run down to me this summer for a barbie now , dont chuck the exhaust if you ever take the engine out then you can fit everything in place tack then weld it back up i think somewhere the exhaust has been overstressed and made it fail , remember that exhaust i had from you that fitted the 500? i had to make some 6mm spacers (between the manifold and exhaust) to push it away from the starter motor and then fabricated some brackets. [-/
-
Yea I'm up for that Mick you've moved now haven't you? Let's see a pic of the exhaust.
I can't be arsed with it I think it was restricting more than the original anyway I will keep hold of it I'm sure you can do something with it.
Grubscrew how much it cost to get that done? Did you have a choice of colours? It's not a enamel stuff chips easy?
-
50 or 60 quid,then the cost of the H.T.paint that you do yourself.Bear in mind ant exhaust held in that way is under extreeme stress,better to get a different type to the poorly one you had.
-
Congrats [-/ I guess you'll be **- a lot now. I only feel safe when driving over a pit if there's someone there to direct me (there's always tyre rubbing with the 126 :P)
-
It was a bit bottom twitching they wouldn't jack it up over the pit because they was worried the wheels moving in lol
-
can you repair threads without drilling the hole out first.. My bottom bolt of the exhaust elbow needs a helicoil or similar inserted...
-
The answer to your question is yes because I have just done it on the rocker mount studs on my cylinder head but it is only really possible because you are working with the relatively soft aluminium head. The M8 bolts & studs have a thread pitch of 1.25 mms so to fit a helicoil the holes have to be tapped out to M10 x 1.25 ( M10 fine). The tapping size drill for this thread is 8.75 mms. As long as you can get the tap started in the hole , so best to start with a taper or 2nd tap, then it should be OK. Bear in mind that you may be removing a bit more swarf/metal than normal so it is a good idea to clean the tap every now and then , especialy with a blind hole. Also I found that cotton buds were ideal for cleaning out the metal particles [-/
-
hi folks
more troubles!! i fitted the new standard exhaust sounds so much better runs smoother aswell.
but when ive been cruising around on the motorway sitting at 55-60 after a few hills the oil light came on went off when i rev or drop down a gear it goes away.
ive got plenty of oil that classic stuff, nice warm air coming in cabin, also thermostat opening fully
it seems to really struggle up hills also flat out down to 35-40.
im gonna check the timing tomorrow also that im using the correct oil my haynes manual saying:
sae 15w/40 castrol gtx
http://www.castrol.com/castrol/iframe.do?categoryId=9024084&contentId=7044829
this website says: MAGNATEC 10W-40 A3/B4
i think im using sae 30 classic
any further ideas?? im a bit mythed
-
The poor performance could just be that it is slightly out of tune. Has the centrifugal oil filter been cleaned out recently & what is the air filter like ? Easy to check if the air filter is clogged just disconnect it or take it out & see if it affects the running [-/
-
I cleaned that last year I haven't driven it since also the airfilter looks clean.
I may change the oil,
-
i was surprised the difference an oil change made to mine
-
OK so check the usual suspects , air being drawn in at base of carb , contact breaker points & ignition timing [-/
-
well that was interesting :- one burn, one cut, and a couple of shocks later and the timings setup.
adjusting the dizzy the car has a little miss fire giving me a shock makes me jump then i burn myself on the exhaust!!! is that suppose todo that??
right getting down to business timing was about 4 inches advanced got the strope out and setup according to the haynes manual cars alot smoother and not so loud. pulls alot better but asoon as i put it in 4th gear thats all lost.
would the orginal advancement make the engine hot? also the line was very jumpy sometimes every so often it would be two lines only once or twice is this normal?
sorry about all the constant questions ill buy you all a beer at the next meet ;-)
-
:D Mmmmm! Beer
Yes it is meant to do that , that old hot exhaust will burn you every time </4
Oh you mean the shock ! That HT electricity will take the easiest path it can to get to earth . The system is designed so the preferred route is from the coil to dizzy cap to plug leads via carbon brush then rotor arm & lead contacts in the cap. Then leads to plugs and the spark gap. So if your car prefers to give you a belt of HT electricity instead then you were the path of least resistance.
So could be plugs , modern supressed leads break down in time plus check leads have good contact & are pushed right home . Check dizzy cap & rotor arm condition plus that the cap seats down nicely.
If your timing was 4 inches out I am very surprised that the car would start at all. Anyway , not in the 126 Haynes manual , but in the older 500 Haynes . "Overheating can be caused by timing being a long way out , a carburettor fault & weak mixture or air leak beneath the carb"
Can I have my beer now as all this chat has made me thirsty :beer:
-
Haha i could murder a beer numb the throbbing of my finger! ;D
I'll stock up before the next meet they sell loads of east european beers in a little shop round the corner :-p
Ive done most of it New plugs, new leads I haven't changed the cap or rotor yet or points.
Carb had all new gaskets, I was thinking it may need tuning.
I may take a visit to dyno tune get them to rolling road even just for the video of it on the rollers ;-)
:wave: :wave:
I'm gonna go for a run in it now so fingers crossed the oil light won't come on.
-
well my drive was fun i started off from erith in kent thought i would go for a long coastal drive 8)
car was purring away at 55-60 until i hit the massive hill just after the medway bridge, the car was really stuggling in 4th so i dropped it down to third and pushed on, at the top of the hill i was greated by my friend the oil light again this time just flickering so i got it upto the top of the hill and back upto 4th and carried on driving. The oil light went away and carried on to whitstable on the beach checked the engine over and i was suprised at the lack of heat coming from the engine it was running so much cooler. i thought i would check the electrics over as i was getting a little missfire going down the little village, one of the spark plug screw tops had come undone so i tightened them up and off i went along the coastal road :D i have friends who lives in ramsgate so i headed that way stopping off along the harbour for a couple of pics
(http://i122.photobucket.com/albums/o254/nrg19uk/IMG_0871.jpg)
(http://i122.photobucket.com/albums/o254/nrg19uk/IMG_0872.jpg)
(http://i122.photobucket.com/albums/o254/nrg19uk/IMG_0873.jpg)
went to start and starter motor didnt wanna play, brand new starter playing up??? batts good whats going on so i thought i would bump start it and get it to my friends.
i kicked the gf out to push no luck! then three blokes walked up started taking pictures of the car, just so happened to be polish ;D so in my best english polish accent got them to push
(http://i122.photobucket.com/albums/o254/nrg19uk/IMG_0876.jpg)
car came to a skid every time i engaged the clutch >:(
well that was it the polish guys had the car pushed over to the light, bonnet opened fiddling with the engine.
(http://i122.photobucket.com/albums/o254/nrg19uk/IMG_0875.jpg)
-
and what did they do ?
-
I had to start a new msg as when im typing the page keeps jumping to the top of the text :-
anyway, they pulled the dizzy cap off, dipstick out, couldnt see the ultra clean oil that was in there and thought the engine was seized.
once shaking there hands for there help off they went too the pub and i phoned my friend to bring there tool kit down, the starter lever was stuck open so i thought that was jammed in the fly wheel so i took the starter off minus a stripped bolt and a lobe and boy was it jammed! a couple of clumps with the hammer later it was out. i taped the connections up and bumped started her and she was away :P got her to my friends house and used a piece of wire to hold the connections from the starter together and taped them up out the way.
had a nice cuppa tea and set off for my home journey cruising at 55-60 with the gf worried if i stalled it she would have to push me hehehe
i managed todo 150/60miles on a full tank????
also that if i dropped down to 3rd gear going up hill and sat at 35/40 the oil light wouldnt come on and i need to turn my idle up to stop the oil light coming on at the lights or stationary.
what have i learnt from this? take a half decent tool kit! and dont over tighten bolts.
-
That is a great "blood & guts" motoring story with that all important ending , you got it back home [-/
So well done but where do you go from here ???
-
I thought it went well apart from the starter :) i cant wait for the summer now!
Now I've got too pull the engine Out I've brought some time sert type things and rethread the holes. You will like these rusty only downside is there 3 pound each you drill a 9mm hole and screw it straight in which cuts its own thread solely designed for aluminium and no complecated tools needed just a bolt and two nuts. I'm gonna take the starter back and hopefully they can swap the casing over for a fee
I've managed to snap the choke cable aswell :-
Then I can get the carb tuned! Hopefully that will sort most of labouring issues or I will pull the gearbox apart and change the fourth cog.
On a positive note I went to ikea the other day and found a parcel shelf dumped in the carpark took it home and it fits perfectly :-p I don't know what car it's from
-
I saw those Time Sert kits on eBay last week when I was looking for some helicoil inserts and I thought at the time if they are the real business then they were a good buy , I think the kit was about £35 .
I am guessing that they are a crib on the original Keenserts that I came across many years ago. They are fitted pretty much as standard on race / rally cars but very expensive. If those ones you have are as good you got a good deal :D
Mind you in the "dumped in the car park" department you are a bit of a lightweight as I went to Tesco this morning & someone had dumped a half size Strat look alike electric guitar in the bin. Got it sorted and now I am a "guitar hero" having fixed one last week as well so going down in a blaze of glory ;D
-
150/160 on a tank isn't too bad, I run to about 120 when my reserve light comes on but then I'm running a Dellorto FZD carb.
Points do tend to jump about on the strobe, I've checked mine for play in the dizzy and found nothing much so figure it must just be how they are :P
Uphill I find I drop to about 50 on the motorway at the top of hills, can be a bugger when there is a big lorry behind... so 35/40 seems a bit too slow up hills.
I found mine with the electronic ignition was rubbish and overheated so went back to points but since found that she prefers to run firing on the arrow rather than the mark which makes me wonder if the mark on the pulley is in the right place :o
It's crazy should fire 10 degrees before tdc at idle and advance to 28 i think but it always seems to advance more than that :oops:
Who knows, I'll wait for summer to tinker more. Thinking of going back to basics, pulling the cam out for inspection for wear, checking timing although it's two marks so what more can it want :P and just work through it slowly.
Sounds like your starter is properly knackered as being engaged it'll eventually seize-up and probably cook itself. :(
-
I pulled the engine out to have a look at the damage the starter has done today
It looked as if someone before had chemical fixed the bolt in too hold the starter!
So I got my new time sert things installed and bobs your uncle one fully working fiat for now :-)
time serts are not the easier to fit you have to drill out a massive 10.5mm hole As for self threading they was a pig to start might be worth taping a thread first just to get it started, they are not gonna move now! [-/
I think they are perfect for bigger fixings and stick with the helicoils for smaller stuff, one good thing is if my exhaust studs pull out I know that these babys are going back. I will post a picture up of the time serfs when I'm at the computer later
:D
-
Neil , has your car got the bracket that supports the back of the stater motor fitted ???
-
I haven't seen any remains of one. Whats it look like and where would it fix too?
-
The bracket fixes with 2 M6 bolts to the back of the Starter Motor and supports the back of the starter motor on an extended stud on the gearbox. It is a fiddly little bugger to fit and from what I have been hearing recently many have been left off from the 126 engines with some pretty bad consequences for the starter motor , etc :oops:
-
If that bracket is not fitted, is the starter comes loose it wil crack the gearbox bellhousing..this happened to me :(
-
Well I don't have one of them! I'm starting to think who ever had my car before hand didn't Like putting things back....
most bolts have not had washers etc
Is it something I could make or has anyone got one they wanna sell?