Club126UK
Fiat 126 Chat => Fiat 126 Chat => Topic started by: Kent126 on November 18, 2010, 02:41:47 PM
-
Finally making some progress. All the bits have arrived now so I have fitted;
new plugs,
leads,
earth strap,
condensor,
distributor cap,
rotor arm,
igntion coil,
He is now in the garage having the new starter motor, cable and fuel pump rod fitted. With any luck the next couple of days will see me back on the road again. Then I can start work on stripping out the interior and giving everything a bloody damn good clean.
(http://i152.photobucket.com/albums/s191/thomasrenshaw/Fiat%20126%20-%20Rusty%20Old%20Brown/IMG_0914-1.jpg)
Can't wait, because getting the train to work is doing my bloody head in!
Tom
-
All your progress will benefit the small car in a big way. Ive just had a new condensor, points and plugs, and it feels more alive to drive [-/
-
Because the 126 carpet comes in a number of sections I used to just put them in the washing machine and they used to come up a treat [-/
Can't do it with the one piece 500 one :(
-
that mechanic looks like he is visiting a museum! or where the computer is meant to plug in for fault finding!
-
Wow! Washing machine? Awesome. Will do that when my flatmate is at work! ha ha. Seriously though? I will give that a go, gotta be worth a try. Reckon you could do the same with the seat covers?
and yeh the mechanic did stand there scratching his head for a while, before saying "Bob, you worked on one of these before?"
All worth it considering I went rolling down a massive hill to bumpstart it, and played chicken with a double decker bus, and WON!
Fun times
Tom
-
that mechanic looks like he is visiting a museum! or where the computer is meant to plug in for fault finding!
That was the impression i had when i saw that pic :P
-
:D I reckon that picture would make for a good caption competition [-/
I would go with "Bob have a look at the size of the heater on this little car" :oops:
Seat covers & washing machine ::) Well I think that would depend upon the material & condition. Vynl OK but probably a lot of work to remove & refit. A lot of the fabric seat covers are a bit fragile also.
-
Mine are going in the machine this weekend, first to was then to dye them black again as they were many years ago. Will it work?
No idea at all.
-
just make sure you get a dye that is colour fast.
-
Well finally got the car back from the garage just over an hour ago. New starter motor, cable and fuel pump rod fitted. Car is now running like a beaut! Will be able to use it for work tomorrow morning for the first time since getting it!
I think its gonna be bloody cold too!
Anyway, on with the project. Next is stripping out all the interior for a damn good clean!
Tom
-
noticed the UK models have black plastic vent on engine door grid .. seen here on original post .. did these come as stock ? do aid in the intake of air... havent seen oz nikis with them
-
The vent covers are an aftermarket thing and their main function is to keep rain & snow out of the engine bay . There are a couple of types , the early ones were like a flat rubber grid with a slider to open & close the vents. Later ones are like a hard plastic scoop [-/
-
Got mine off eBay from Ricambio. Dont like them personally, but due to keeping the car outside, and the impending rain and snow I had no choice. Getting my garage back when I move back to Tunbridge Wells in January, so might take them off as I park in a enclosed carpark at work. Here they are fitted, two screws, simple as that! [-/
(http://i152.photobucket.com/albums/s191/thomasrenshaw/Fiat%20126%20-%20Rusty%20Old%20Brown/IMG_0882-1.jpg)
(http://i152.photobucket.com/albums/s191/thomasrenshaw/Fiat%20126%20-%20Rusty%20Old%20Brown/IMG_0880-1.jpg)
Tom
-
Hey Tom when you down this way again, you`ll have to came over. By that time I should have a 126 again. There are currently two 126s whizzing around TW on regular bases.
I think those engine covers could be a bit taller. Can`t imagine there is much hot air escaping through them, which shouldn`t be a problem in winter.
-
Dont try the washing machine thing on original 126 fabric seat covers.
I tried it once....the cover didnt survive :(
-
that "heater" must have some bolts loose, bet it will stop shakin if i hold the bumper :D
-
Cheers Kent , I seen some for sale that fit on the inside... just cant remember where
-
Cheers darrell I wont wash the seat covers! lol.
Yeah deffo, sounds like a plan! looking to move back on January 15th to my old place just down Upper Grosvenor Road, so always up for beerage and tinkering sessions! Be nice to have another 126 owner close by! :D
Tom
-
There are currently two 126s whizzing around TW on regular bases.
Just realised, did you see an orange LHD one last year? If so that was probably me when I lived there before after I bought Jan's from him in the summer?
If not then there must be another two in the town! :D
Tom
-
No, I don`t think it was you. I saw your used to be 126 at the Windsor show. It`s still looking good and now has some tasteful mods.
Beerage sounds good to me [-/
-
Noooooooooooooo!!!!!!!!!!!! Was totally original factory mint condition!!!!!! :-( but the guy who bought it, now doesn't own it and sold it on again. I tried tracking him down but with no success. Be good to see it again in the flesh though.
Tom
-
Car died again yesterday! Still think there is some sort of electrical fault relating to the ignition. Now looking at changing the points, belt, checking the belt tension and then see where we go from there, but there cant be much else that needs changing now! :-(
Tom
-
Tom this is what Fiats are famous for , the electrics. I had a problem with a '67 500 that kept cutting out. Turned out that previous owners had knackered the ignition switch proberbly by having too many keys / weight on the key ring. It forced the back off of the switch.
Then more up to date I had a brand new Bis that kept on cutting out. The car was under warrenty but the garage could not locate the problem (they said) but it was obviously in the wiring loom. I could not locate the problem either so I ran a wire to the input side of the coil back through the car . I left the cover for the interior light off and when driving if the engine cut out I just connected the crocodile clip on the wire to the live feed to the interior light , crazy but it worked [-/
-
My BIS used to cut-out and it was because the fuel pump rod was worn. When the engine hets hot the casing expands and stops working the pump.
When it cuts-out check for spark and check for fuel being pumped. That way you get closer to the issue.
Rusty's idea has merit to see if the feed to the ignition is intermittant.
Welcome to the world of Fiats ;) Fix it again tomorrow ;)
Eventually one gets through the problems and they become very reliable but thats why I say 'mint' is a car that will need alot of work as they havnt had all the issues ironed-out :P
-
Cheers guys, fuel pump rod brand new and just replaced, so hoping that is one less thing to worry about. I will have a prper fault finding session tomorrow and post my findings! [-/
Tom
-
Yes new rod is a good thing to have but still check fuel as odd things happen to fiats like wear in the mechanism in the pump and sometimes poor quality parts.
My advice is always go back to basics fuel and spark.
-
Carpets out and slowly going through the washing machine. [-/
Right running issues still, I have checked the points and they open and close fine. Although I didn't see a spark when the engine turns over so could this be the issue? I was told you should see a blue spark?
Engine starts fine, but idles a bit rough and if you apply any throttle then it slowly dies and wants to cut out. It will cut out on full throttle.
I have checked the throttle linakge, and lubricated the cable, linkage and pedal as best as I can.
I think there was a slight misfire, however.
The choke cable is fine, and the choke opens and closes as it should. When you run it with the choke ever so slightly open, it idles better.
There is a new fuel filter, and the fuel looks fairly clean, and the fuel stays sat in the filter when the engine is off, so I am thinking it is not a fuel pump problem? The new fuel rod has also been fitted.
I think the condensor I had replaced the old one with was slightly dodgey, so another new one has been ordered.
I am thinking it could now be more of a carb problem, and perhaps it might need cleaning?
Regards,
Tom
-
If it has a fuel filter installed one would like to assume it isnt the carb but then we are dealing with a 126..
I suspect the condenser first above everything else as I had a look at mine the other day and she does spark a little when running (mine has the two chimney coil with no dizzy cap) so I can see the points operating when the engine is running.
Personally I find one should order 3 condensers every time, as often it's third time lucky
-
Blimey, are they really that poo? lol
-
It does sound like there's not enough fuel when the throttle opens (is the engine cold, cause it sounds like it runs fine with the choke on). Best to check out the carb (could be just dirty..)
Condensers really can be that bad. I've seen new ones installed and the car not starting (another new one was needed).
-
Carpets do come out great in the washine machine don't they? [-/ The bolts to get the front seats out of the sliders are pesky though!
(http://i152.photobucket.com/albums/s191/thomasrenshaw/Fiat%20126%20-%20Rusty%20Old%20Brown/25-11-10Cleancarpets2-1.jpg)
(http://i152.photobucket.com/albums/s191/thomasrenshaw/Fiat%20126%20-%20Rusty%20Old%20Brown/25-11-10Cleancarpets1-1.jpg)
Anyway, hopefully should look and smell better upon re-fitting! :D
Tom
-
Ok thanks GT master. This problem started happening after I fuelled up!
Will order more consenors!
Tom
-
Right, it is definitely not the condenser. Just replaced it, after trying a few. This one is definitely working. It has a brand new coil, but im gonna test the coil tomorrow just to satisfy myself that it is working.
It's gotta be fuel related.
Tom
-
Try to adjust your points, make sure the gap is correct and adjust the timing. Most of the time I had problem with a 126 it was down to ignition. If this doesn`t cure the problem clean the carb as suggested.
-
Was looking on the fiat owners club forum, and was told that it could be the carb is drawing in too much air, due to an air leak, or possible gasket failure? Will check this along with the points and timing.
Tom
-
FOUND THE PROBLEM!!!!
Carb full of poo and silt, has been removed by mobile mechanic and taken away for cleaning and rebuild.
I have been trying to get the fuel tank off today for cleaning out but it appears rather difficult as one of the bolt is knackered, and might need drilling out! hmmmmm
(http://i152.photobucket.com/albums/s191/thomasrenshaw/Fiat%20126%20-%20Rusty%20Old%20Brown/06-12-10Carbremoval4.jpg)
(http://i152.photobucket.com/albums/s191/thomasrenshaw/Fiat%20126%20-%20Rusty%20Old%20Brown/06-12-10Carbremoval2.jpg)
(http://i152.photobucket.com/albums/s191/thomasrenshaw/Fiat%20126%20-%20Rusty%20Old%20Brown/06-12-10Carbremoval6.jpg)
Tom
-
Well.........carb was re-fitted yesterday after a strip, clean and re-build. Service kit used with gaskets, float, new washer, nut and spacer. That seems to have done the trick along with all the other bits and peices replaced, the old carb parts were knackered on inspection!
Choke cable snapped today, so new one on order. Accelerator still sticking so new cable ordered also (tried lubricating and cleaning linkage but no joy!) so it must be the actual cable itself.
Also didnt manage to get the fuel tank off due to a knackered bolt, so might need to get it back into garage to get them to whip it off and clean it out for me.
Apart from that, it would appear we are back on the road again. Tomorrow im driving from Maidstone to Corringham in Essex, and back again. Should be interesting.....
Tom
-
Tom , from your picture it looks like you have an online filter fitted plus there is a mesh filter inside the carb . So if the petrol is pumping OK and the online filter looks clear I would not worry. Taking the tank out is not a nice job at the best of times so I would go with a good shot of Redex , full tank of petrol and just keep driving the little beast [-/ Then drive it some more :D
You can have fun driving whilst blowing through any c**p at the same time. A bit like those yoghurts that "aid your digestive tract" ::)
-
Thanks Rusty, yeah the inline filter is brand new, and the contents look really clear. Also the little mesh filter on the carb has been changed also.
I will fill up tomorrow with some fresh fuel and give him a blast over to Essex and back. Lets hope the girl im picking up appreciates the little beast! [-/
Tom
-
:cry: FFS! Another breakdown!
Started kangarooing again badly so pulled over and got my mate to tow me home!
Back to the drawing board!
Tom
-
Good luck Tom, you'll get to the bottom of it and then it'll shock you as to how reliable it will be.
I carry a piece of wood so I can push the starter from the back and a spark plug so I can sheck for spark. If I think it's fuel I simply open the drain on the carb to let any rubbish out but kangaroo hopping could be either/or. Sometimes choking the carb with ones hand can pull any dirt in the carb through but quick fix to get home only, if there is still dirt in the carb I suspect that filter you have is an ornament... A bit like my Jack Russell's ears!
My BIS had a horrible habbit of running short of fuel as the fuel pump, even with a new rod and spacer still seemed to stop operating when it got hot. A quick fix was to make the spacer thinner.
I fitted an electric pump and regulator as I have done on my air cooled.
Pete says he went through starters because of the pump so makes sense.
-
Tom thumb a lift did ya ???
Ok sick joke over & that is a real pain and sorry to hear that but do not panic ::)
Question is fuel or ignition & from what you have said I would put my money on fuel. Did you try the redex as it has a cleaning effect from the tank onwards ???
Not to be tried by children or people of a nervious inposition but I had a 126 that had been standing for quite a while . The pump was good but could not get the fuel up to the carb. To prove this I found a good sized pickled onion jar which was a good fit in the space where the air filter fits. Punched a hole in the lid & ran a hose down to the inlet on the fuel pump. Petrol pumped through fine and the car was driveable. Proving the tank line was the problem. Points to note, make sure no petrol can spill out, if you do drive the car you have a petrol "tank" that is slightly more robust than an egg & if you do get a back fire then you may shoot a flame at your new petrol tank . All that said it is a way of identfying or eliminating your problem [-/