Fiat 126 Chat => Tuning & Customising 126 Models => Topic started by: Rusty's Uncle on June 26, 2010, 02:55:24 PM
Title: And So It Begins :-)
Post by: Rusty's Uncle on June 26, 2010, 02:55:24 PM
Various projects are moving along slowly but my 500L daily runner has been a bit off colour plus I wanted to try a minor upgrade on a standard 499ccs engine. Plan is to fit 126 camshaft , carb and exhaust along with the ported 500 head with enlarged inlet valves that I have just had done. Hopefully modest mods & an engine that breaths a little better. I thought that the poor running may have been down to a blown head gasket or a valve but no evidence of that. Also engine has a real rattle so timing chain was suspect. This car has now done just over 100,000 miles so you are not sure what you will find :oops: Took a picture to show the sag on the timing chain but it did not seem too bad , compared it with 2 other used ones & they looked very similar. Will dig out a new one later to compare. The Haynes Manual says that removal of the cam is best done with the engine out as the followers can drop. So just lifted the followers and pushed a bag tie through the holes in the follower , can't drop now ;D More to come [-/
Title: Re: And So It Begins :-)
Post by: Darrell on June 26, 2010, 10:51:07 PM
Thats a might fine looking big timing chain sprocket on there Rusty ;)
Never seen a lightened one like that before
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on June 27, 2010, 06:37:51 AM
Finished the stripping now , found one minor & one major fault. Firstly the little petrol drain tube (not fitted on 126) had dropped out of the carb drip tray so may have been drawing a little more air there. The other thing was one of the inlet lobes on the camshsft had worn down badly & was a full 2mms lower & just over 4mms os cam lift. Also considering that the engine had a major rebuild by a well known Fiat 500 specialist about 25,000 kms ago I was very surprised to see the worst build up of sludge in the centrifugal oil filter that I have ever seen. Almost built up to the outer edge of the oil flinger behind the big pulley nut :oops: Now that camshaft sprocket. I only realised it was different when I dug out the others I had which are cast iron. This one looks as if it may have been machined from solid , weighs 215 grams as opposed to the 315 gram cast ones. No idea how it ended up in my standard 500L engine ::)
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on June 28, 2010, 09:27:03 PM
Started the assembly today , 126 cam in , timing chain on then checked out the oil pump which is quite an experience to get it apart & back together . Almost screwed up refitting the timing chain cover . PIcture of the pile of poo that came out of the oil filter , weighed in at 120 grams plus the tool that Haynes dared not show ! How to re-torque the crankshaft pulley nut :oops:
Title: Re: And So It Begins :-)
Post by: bis13 on June 28, 2010, 10:28:00 PM
ha ha so you found that fun too! its special tool no1! did you have a bit of bother with the timing chain etc? i know you are an old hand but i hope you have replaced all the sprockets along with the chain if you have changed it? with regards to the worn lobe what inlet was it on as mine wore down and wondered if its the same lobe?
Title: Re: And So It Begins :-)
Post by: Darrell on June 28, 2010, 11:04:26 PM
I thought about that Mick when I saw your cam had worn one lobe down.
The cam from what I understand relies on oil coming from the head, down the tubes into the cups, through the cup holes and onto the cam.
I thought maybe one of the tubes could be sticking-up into the head too far thus not allowing any oil to flow down or perhaps the casting channels the oil to all but one.
Perhaps the angle of the engine affects this as I've noticed mine sits a bit up at the back (pulley side)
My cam will be coming out soon so will do an inspection too.
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on June 29, 2010, 03:51:06 PM
The inlet cam lobe that had gone was on the no 2 cylinder. No indications as to any cause for oil starvation but two cam followers were pitted on the face & two of the steel cups at the top of the push rods were slighly loose. All replaced by good used components. Made more studs to fit the exhaust elbows to the head so as to avoid stripped threads from bolts. Fitted exhaust elbows and picked out a head gasket which turned out to be 0.015" thinner than the one that came off so minor compression rise there. So now you are "torqueing" & head etc fitted [-/ Still lots to do but getting there.
Title: Re: And So It Begins :-)
Post by: Allan on June 29, 2010, 09:18:02 PM
Hope you set the tappets before you put the rocker cover on. One thing I used to do after a job like that was to get everything else done including the tappets and leaving the cover off start the engine briefly (as soon as it fires one small rev and then turn off) then recheck the clearances. What are the pins in the gasket for? Allan
Title: Re: And So It Begins :-)
Post by: bis13 on June 29, 2010, 09:38:44 PM
thats a form of accupuncture for perfect gasket alignment....
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on June 29, 2010, 09:59:22 PM
:D yes provisionary set the tappets for the first run bearing in mind the parts that I have replaced that will bed in ( I hope ) ::) Now I delibrerately did not mention those pins , I thought that eagle eyed Darrell would have been straight on it , Allan you beat him to it [-/ The thing is I think that a lot of the oil leaks come from a poorly fitted rocker box gasket and the gaskets do tend to bow in along that straight edge above the thermostat housing. So I had the idea of putt ;)ing in those two pins to align the gasket & it seemed to work fine
Title: Re: And So It Begins :-)
Post by: Darrell on June 29, 2010, 10:09:43 PM
Eagle eyes was out riding motorbikes :oops:
Had a go on an old '84 Suzuki Katana and an Suzuki SV....got a head full of adrenaline after having a go on that SV....front gets mighty light under acceloration :oops: :oops:
I had a similar problem so I contact adhesive-ed the gasket to the rocker cover. A light coating of grease on the other side means it comes-off easily and goes back on easily.
Rumour has it from an old school mechanic I hung around in my youth observing work on old brit bikes, that grease was commonly used between gaskets.
I have to confess to the use of silicone on the carb inlet as I wanted that to seal like a ducks... [-/
Title: Re: And So It Begins :-)
Post by: GTMaster on June 29, 2010, 10:14:57 PM
Looking good [-/ How much more power can be expected? Another good way to tighten crankshaft pulley nuts/bolts is either with an air wrench :) or if you have a helper and the engine's connected to the gearbox then by putting it into gear and having the brake pedal pressed (or if you have a good handbrake then that may be enough).
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on June 30, 2010, 08:24:04 AM
The guy who did the work on the head reckoned the porting would give an additional 2.5 to 3 hp per cylinder which would be a huge rise for a little 500. Then of course I had inlet port enlaged to suit a 126 carb, enlarged inlet valves fitted and the 126 cam so it is all a bit of an unknown ::)
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on June 30, 2010, 08:19:34 PM
So I got a little bit crazy & a bit impatient today, played with the exhaust & wanted to fire the thing up asap :oops: So I took the angle grinder & welder to the standard 126 exhaust for a posey tailpipe then pressed on with the re-assembly . Had to make longer studs for the exhaust brackets plus one for the 126 carb. Had forgotten that the rocker side stud is longer on a 126. Was going to rebuild a 126 carb but spotted a clean looking one in my garage & went for it (do a rebuild later , honest :oops:) Tried firing it up but no joy but I wanted to get the oil pumped round anyway. I had tried to be clever by just lifting the distributor off the old cam then dropping it down on the new but it was not right so after a quick rejiggle we had ignition :D Interesting as the engine is only supported by a large block of wood with a smaller block on top . All OK on tickover , quite a bit of vibration with more gas & on the over run but after about 30 mins of running to let things bed in oil circulate & get up to temperature I tried a good dab of throttle and sounds promising. Engine support / lower panel going back on in the morn then a road test [-/
Title: Re: And So It Begins :-)
Post by: Darrell on June 30, 2010, 08:44:25 PM
Rusty I tried doing that with my original exhaust, it looked and sounded good but kept on cracking, it needed to be well braced.
Just thought I'd tell you while you havn't got too much bolted-on to do anything :oops:
If you dig into the standard 126 pipe there is a baffle just behind where you welded-on your new tailpipe. Did you take tha baffle out?
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on July 02, 2010, 01:36:20 PM
You were spot on there Darrell :oops: My "silly" exhaust lasted about 3 miles before the tail pipe decided to go it's own way. Funny thing was it was the metal adjacent to my weld that failed . Not sure what grade of steel the pipe is made of but it did not weld like normal mild steel . I think I may have also aggravated the situation by sticking a four foot lever up the tail pipe and bending it to a more pleasing aspect ::) Anyway I carried on regardless and did a 30 mile run. The engine seemed a bit flat at low revs & more vibration on slow tick over. Felt like more power through the middle range tailing off at max. Stalled a couple of times and the hot & cold starting characteristics seem to have changed. I had set the 123 ignition as per instructions but reset the timing with a strobe this morning. Another 30 mile run and scared myself within the first mile when I was way too fast on a corner then I realised I was driving a different animal from the day before. Lots more grunt under the right foot pretty much through the rev range and 3rd gear is quite good fun. Still some tidying to do & the exhaust to sort out but it seems that the project has worked in that I have a very standard looking 499ccs engine that packs a little more punch [-/
Title: Re: And So It Begins :-)
Post by: Darrell on July 02, 2010, 01:55:45 PM
The only way I can think of to make a tail pipe work it to weld a piece onto the elbow, take the baffle out and weld the new bit inot the exhaust eg. through the silencer, allow for bigger holes to get more through flow and keep the elbow tight so you can weld it to the silencer further toward the back (tip) of the tail pipe.
I gave-up in disgust, the metal seems to fracture always next to the weld, and bought a sport pipe off e bay.
Although the sporty pipe has never cracked, the finnish (black) is rubbish, it went white-ish and has started rusting already.
I'm saving for a CSC pipe in stainless with the elbows to bolt directly onto the head [-/
The 123 set-up I also found to be lame without the use of the strobe.
Tell me...did you set it with a timing light with the knob to set 10 degrees and then use the TDC mark or a static timing light where one would set it to flash on the 10 degree mark?
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on July 02, 2010, 07:05:22 PM
No knobs or frills on my trusty old strobe. Just two clips on leads & a light that flashes. Highlight TDC on the pulley with tipex then use my judgement as to the 10 degrees or 13mms before TDC ;D Anyway I am sure there will be more news but in the meantime I would like to thank all of you guys that gave me advice , encouragement & helped with parts [-/
:D you can teach an old dog new tricks :D
Title: Re: And So It Begins :-)
Post by: Allan on July 02, 2010, 09:28:11 PM
Don't any of you folks own the genuine Fiat timing plate?
Title: Re: And So It Begins :-)
Post by: Allan on July 02, 2010, 09:48:55 PM
Just as aside, one of the things that I have learnt to do over the years, is when the opportunity presents itself, using a dial gauge, check the timing marks line up at TDC. You would be amazed how many are a few degrees out. Allan
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on July 06, 2010, 10:09:49 PM
I have seen those timing plates in all the manuals for years but have never seen one for sale. Which brings me round to the fact that I think that getting the best out of my 499ccs engine is now down to fine tuning & tweeking. Lot more power but tick over is a bit "thumpy" , middle range seems pretty sweet with a much more relaxed cruising speed. It will pull to 90 kms/hr in 3rd (top speed on a standard 500L is 95 kms/hr - 59 mph) I think that I may have the timing a little advanced hence the lumpy bit then I have been looking at the tuning curves on the 123 ignition that may be more beneficial higher up the rev range. 126 carb jets are also similar to the rare 500 Sport so I think the carb is OK for a modest tune. [-/
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on July 07, 2010, 03:13:58 PM
Decided to have another go at my "silly" exhaust this morning otherwise I would have to scrap it. Took more time over the welding plus added in a brace to the tailpipe. So far so good and having a tailpipe that extends out to near the rear bumper has made the car so much quieter. Had a run around then had another go at the timing & 123 ignition. I now have a a new timing mark on the timing chain housing. Not a genuine Fiat part but a rusty 30 mms nail with a large head & about 8 mms bent to 90 degrees at the sharp end. I wanted a clearer indicator at the 10 degrees before top dead centre position. Head of nail cleaned , a bit of measuring and cleaning then the "indicator" has been super glued in place. A bit more with the strobe 7 timing then I set the 123 ignition to "4" which is described as tuning curve group 1. Only had a chance to go around the block & down the hill & back but all seemed very promising [-/
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on July 08, 2010, 12:33:28 PM
The next thread I start will proably be "And so it ended" >:( All was going well this morning then I got out on the dual lane road & giving it some in 3rd to try the new settings. Strange mechanical noise along with a smell of burning oil. Shifted to top gear & car drove OK. Pulled over to test all gears then pulled away OK. Then pulled in again to check in engine compartment. Engine running but small smoke cloud around top of engine. Could not see why & engine was running OK in fact tick over was much smoother. So turned for home , about 5 miles away, and all going well . Noticed power dropping with about a mile to go but fingers crossed. Unfortunately I live at the top of an extremely steep hill & it could not make it in first gear. Rolled back into a side road & the engine died. Opened up the engine lid & quite a bit of smoke. Very , very hot in fact the paint on the rocker box cover was blistering , petrol was vapourising in the filter, no oil loss in sump. Managed to get the oil filler off as it was too hot to handle. The plastic washer on the pressure relief valve is missing so it may have melted & dropped into the rockers. Waited 30 mins to see if it would start , no joy. Walked home & waited 30 mins. Went back home then returned over an hour later. The engine was still hot but touchable. Would not fire up. Now waiting for a tow up the hill so I can check it out . :cry: Hoping it is not too messy :oops:
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on July 08, 2010, 06:45:50 PM
Done a bit of a strip down, Rocker box cover off, absolutely no sign of the washer from the bottom of the oil filler. The extreme heat had caused the raised face on the bottom of the rocker cover to "burn" through the gasket. Blackened oil on the head top above no 1 cylinder, tappets were loose, as were the rocker mounting nuts. Carb off then removed the fan top cover / air filter housing. Not a pretty sight as all I could see was mangled metal. Removed the rear lower housing and a load of bits fell on the floor. Now the first scarey bit , I counted 14 blade locations on the rim but only 7 bent & buckled blades fell out. Absolutely no sign of the others :oops: This fan looked fine a week ago so I might have to call in the X-files on that one. The dodgey bit is that I had no warning of this in terms of noises etc. The next question is how much damage has been done by the extreme heat due to the fan failure ::) Pic of DIY 7 blade fan rebuild kit posted.
Title: Re: And So It Begins :-)
Post by: GTMaster on July 08, 2010, 07:38:13 PM
Seeing that all i can say is: oh c**k ! :( Feel sorry for you.
Title: Re: And So It Begins :-)
Post by: ChrisRLewis on July 08, 2010, 08:31:38 PM
looks nasty, just hope your motor is ok. Do you have a spare fan? I've got a spare one if you need it.
Title: Re: And So It Begins :-)
Post by: Darrell on July 08, 2010, 09:29:18 PM
Bugger!
Mine overheated once very badly with power loss when the fan belt broke, unknown to me the bulb had blown for the battery light, I just didnt notice it had blown! It's now a big thing on my check-list when starting it.
Somehow it hasnt done any serious damage, I stripped it down to the pistons and put it back together, it runs fine now.
The later overheating was weird because i think it was a little harsher if that makes sense. When the loss of power comes-on with no fan one can imagine the pistons struggling to go up and down. So I checked the pistons. Turned-out I needn't have.
Later on she was overheating because of the ignition and that heated the whole engine slower, which somehow was worse which cause the rear bearing to pinch. Cross fingers it might be ok :-X
Title: Re: And So It Begins :-)
Post by: 1973/126 on July 08, 2010, 10:28:51 PM
Not a nice site. As said, hope the engine is O.K., but the fact it wouldn`t start even after cooled down is not good. Maybe it would be worth investing in one of those alloy fans. I remember the 126fan guys said they only use those on they race engines, as the standard ones just brake up at such high revs.
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on July 09, 2010, 01:03:56 PM
Thanks for the support guys and also to Chris , I do have three other fans. One standard, one stripped & zinc plated then powder coated then the HD plastic on steel base one that I have from the Alquati engine. [-/
Title: Re: And So It Begins :-)
Post by: ChrisRLewis on July 09, 2010, 04:10:16 PM
Just a question on fans. I checked the two spare fans that I have and they are slightly different, the vanes on one of the fans are longer. So the question is are there different versions of fans for 126's?
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on July 09, 2010, 04:52:29 PM
Yes that is interesting as I guess those extended vanes would scoop more air. I share Darrells frustration as I had very little warning , especially as I was paying particular attention to the engine after the rebuild. I should have paid more attention to Freddie Mercury " Scaramouche , Scaramouche did you hear the damn fan go !" :oops: :oops: Any way I was quite worried about the missing blades , Mick reckoned they might have been trapped in that little section between the fan housing & the sump cooling channels. That was not the case but there is a chamber in the sump entry. I picked out the missing 7 bent blades & a spark plug that looks like it has been in there for 20 years or so ;D
Title: Re: And So It Begins :-)
Post by: Darrell on July 09, 2010, 06:27:04 PM
Work-wise I am in irrigation, and with water pumps the wider the gap in the impellor the more water will flow, the wider the impellor the higher the pressure. The theory would is the same for air. A closed impellor is more efficient than an open one and the smoother the surfaces within an impellor the more efficiently the water/air will move through the impellor. Remember that the power sapped from the engine will also be affected by the wider impellor.
The eye of the impellor should be as close as the tollerance can be as air will simply re-circulate into the eye, out the vanes and back into the eye.
I have often wondered what the point of the alloy fans is as they cannot be better than the closed tim ones. I guess they don't fall apart. They will draw the same power from the engine as a closed one.
By my thinking, the plastic fan would be an ideal as it would have smoother surfaces. Longer vanes would also be beneficial. The belt I have long suspected to be a floor as there is only so much tension one can put in it before bearings in the altenator quit. I see there is a toothed belt available...at a price which I see as an ideal as it cannot slip even with relatively small amounts of tension. By toothed i mean tothed like a timing belt.
Title: Re: And So It Begins :-)
Post by: michaelodonnell500 on July 09, 2010, 10:35:07 PM
Sory t hear about the engine, I'm only down the road if you need any parts, or a spare hand.
Title: Re: And So It Begins :-)
Post by: Alfons1972 on July 10, 2010, 06:41:26 AM
yes, Darrell,
there are those toothed belts. They are installed primarly because they need less power because of less rotation speed of the fan and therefore less resistance. And because of less tension, of course. The consequence is less cooling, too. And you probably will need an oil-cooler...
Title: Re: And So It Begins :-)
Post by: Darrell on July 10, 2010, 09:06:34 AM
How can there be less cooling with the toothed belt? It cannot slip, diameters are the same, surely more cooling?
Title: Re: And So It Begins :-)
Post by: Alfons1972 on July 11, 2010, 07:23:50 AM
ok, Darell, I just looked for those kits. I thought of those kits with the same diameter...
there are different types: - with the same diameter http://www.500forum.de/wbboard/attachments/00000002863__4381__DSC05645-border.jpg - with different diamteters http://www.500forum.de/wbboard/attachments/00000001516__8602__DSCI0759.JPG
so we both are right... ;)
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on July 13, 2010, 08:59:51 PM
The engine fired up today , still a few bits to do & yet to roadtest but such a relief that the major expensive bits seem unharmed ::) Decided that the best option was to fit the HD plastic fan & yes it is slightly lighter than a standard at 620 gms as opposed to 680. This episode has taught me a few things. The very brief noise I heard when the engine was at max revs in 3rd gear must have been the moment when the fan "let go" . Probally less than one second , not too loud but the results quite scary with bent & buckled metal & two vanes had pierced the upper steel housing. :oops: Also they are not called air cooled for no reason because without that fan you do net get too far. To be continued ........ low battery warning :P
Title: Re: And So It Begins :-)
Post by: bis13 on July 13, 2010, 09:42:56 PM
good to hear that the costly bits have made it through unscathed!
Title: Re: And So It Begins :-)
Post by: michaelodonnell500 on July 13, 2010, 10:29:37 PM
crackin news!!!
Title: Re: And So It Begins :-)
Post by: Jan-in-UK on July 13, 2010, 10:48:42 PM
Yes, CRACKIN :)
Title: Re: And So It Begins :-)
Post by: thepuddlejumper on July 14, 2010, 01:15:01 PM
Glad to hear all is OK
Ralph
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on July 14, 2010, 02:16:44 PM
Cheers Guys [-/ First indicators are good as I have been out on a couple of "missions" this morning and all seemed to run quite sweet. So first lesson is that if you are tuning an aircooled engine then an uprated fan or a rev limiter might need to be part of the package. Also you need to check that the cooling air intake is clear & jumbo hose properly fitted. Also on my high mileage engine there was heaps of crud inside the cooling fan housing and I have not checked yet but I am wondering if the cooling ducts along the base of the sump are clear. Most of the air cooled cars I have run without the grommet type cover that goes over the top of the spark plug recess. But on start up yesterday I was aware of the terrific flow of air comming up that wat instead of being blown across the head so got those fitted pdq ;D Should make Uxbidge show on Sunday </1
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on August 17, 2010, 06:45:28 PM
Just a question on fans. I checked the two spare fans that I have and they are slightly different, the vanes on one of the fans are longer. So the question is are there different versions of fans for 126's?
I remembered Chris's question as I spent well over an hour trawling through every known web site trying to see if the high density plastic fan I am now using is still available anywhere. No luck but I think that it was on the Axel Gerst site that 3 fans are shown , Standard , Alloy & a Superior Fan that had those extended vanes, said to be balenced and about twice the price of the Standard. While I was thinking about it I just checked the fan belt drive on my car & the engine pulley is about 6" diameter & about 4" at the dynamo so by my reconning if you hit 6,000 rpm then you are going to be pushing that dynamo & fan at about 9,000 rpm :oops: Smallcox told me he has tried a very short run with the fan belt off & noticed a major increase in power. Might be alright for a standing quarter mile but do not try it out around town ;)
Title: Re: And So It Begins :-)
Post by: Darrell on August 17, 2010, 09:08:37 PM
I have seen a number of performance engines with a 1 to 1 ratio running the fan eg. same size pulley on both pulleys but with a toothed belt. Makes sense as the fan would run slower.
Title: Re: And So It Begins :-)
Post by: smallcox on August 29, 2010, 11:58:09 AM
Now Rusty,
You know that in the good old days dynamo's where not designed to run at high speeds, 9000rpm bad boy
Smallcox
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on September 09, 2010, 01:06:52 PM
All has been going well and enjoying being able to accelerate up hills then gave the little beast a good thrashing on Sunday on a 30 mile run. Then had a bit of the old dodgey tickover at lights over etc , died on me once. Also a couple of times recently the engine has been reluctant to start , possibly fuel but not sure yet. So gave it a pull today and started fine then as the engine was getting warmed up there were times when the tickover got very poor. :oops: That is one thing but as I was leaning on the back of the car I could feel hot air blowing onto my arm and realised that hot air was blowing back through the air intake above the engine cover . Still no thermostat housing fitted yet so put my hand down there and lots of very much hotter air blowing past the head & cylinders. So I would be interested to know if other "Aircoolers" are experiencing anything like this ???
Title: Re: And So It Begins :-)
Post by: smallcox on September 09, 2010, 02:40:09 PM
Hi Rusty,
There you go again talking hot air, and sticking your hand down there. :oops:
Is it just radial heat lerking about the engine bay because your not moving?
Title: Re: And So It Begins :-)
Post by: Darrell on September 15, 2010, 12:27:41 AM
I'd agree with Steve, however the 500 draws it's air from a vent just aboved the engine lid, hence Rusty must be refering to this vent, the same would be true is a 126 was pushing hot air out the side vents.
That's an odd one if I got that right :oops:
I'd expect airflow into the engine not to allow any hot air to flow back? I wonder...pull the big hose off the tinware and check you fan is still ok maybe :-X
Title: Re: And So It Begins :-)
Post by: Rusty's Uncle on September 15, 2010, 08:35:16 AM
I can tell you that there is plenty of air blowing past & cooling the engine but there is also hot air blowing back up out of the vents that Darrell mentions. I do not think that I took a picture of the plastic fan before I put it in but it is similar to the alloy ones but with more vanes. So It does not have the outer plate opposite the main mounting plate. Could it be that this plate on a standard fan acts as a baffle to prevent this blowback ???