Club126UK

Fiat 126 Chat => Fiat 126 Mechanical Problem Solving => Topic started by: Darrell on June 20, 2010, 09:50:48 PM

Title: I think my engine is creating too much back-pressure :(
Post by: Darrell on June 20, 2010, 09:50:48 PM
I might be wrong but I'm finding leaks here and there.

There must be alot of 'breathing' with two pistons going up and down.

Rings? or valve guides perhaps? :oops:
Title: Re: I think my engine is creating too much back-pressure :(
Post by: bis13 on June 20, 2010, 10:26:55 PM
didnt you change the rings ?
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Darrell on June 20, 2010, 10:31:53 PM
I did.

But she has been getting hot in the not too distant past, but this engine always seems to have had alot of backpressure....

It's done 48800 miles, same engine as numbers match i think.

Maybe I should just do rings again and new guides to be sure to be sure :oops:
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Darrell on June 20, 2010, 10:36:03 PM
I wonder how to isolate between valves/rings or test one or the other to know which is at fault?
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Pete126 on June 20, 2010, 11:21:41 PM
Take the plugs out and check the colour on this link

http://www.verrill.com/moto/sellingguide/sparkplugs/plugcolorchart.htm
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Allan on June 21, 2010, 01:34:15 AM
If you can find the equipement a cylinder leakage test will tell you where it's escaping. Used a lot for aircraft but also very effective in diagnosing car engines as well. They work by pressurising the cylinders one at a time. You can get a reading of the % of losss as well as listening at the carb for hissing (inlet valve) exhaust pipe (exhaust valve) and engine breather ( rings)
Allan
Title: Re: I think my engine is creating too much back-pressure :(
Post by: ChrisRLewis on June 21, 2010, 11:04:55 AM
just an idea, are you using synthetic engine oil? if so its prone to cause leaks on old motors.
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Darrell on June 21, 2010, 11:08:58 AM
No I use mineral as I burnt my fingers with synthetic in my old Yamaha XS1100

I think that leakage tester is a mighty fine idea and have aquired one on e bay :oops:
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Rusty's Uncle on June 21, 2010, 12:34:32 PM
Hey I like that cylinder leakage test idea , I did not know these things existed  :(
Reckon I will make my own one as I am not rich like Darrell  ;D
Going to crack the ceramic centre out of an old spark plug , set in a pipe extension with a nut on top and a normal car tyre valve then I can use a foot pump or small compressor on it  [-/
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Darrell on June 21, 2010, 02:53:47 PM
this is a sneaky tool  ;)

http://cgi.ebay.co.uk/GSI-G7200-Cylinder-Valve-Pressure-Hose-/180487887904?cmd=ViewItem&pt=UK_Hand_Tools_Equipment&hash=item2a05ea9c20
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Pete126 on June 21, 2010, 06:54:31 PM
Where is the engine leaking oil ??? If the plugs are running clean then i don't think that is the problem. you would be able to tell if the rings were shot or the valve guides because on the overrun it would be pouring blue smoke out of the exhaust. it would also be difficult to start due to the lack of compression. If your engine does not have any of these symptoms you don't have a problem.

A couple of weeks ago you replaced the sump for the large capacity alloy one, did you check that the mating surface was flat and true some of the repro's are rubbish ??? you also had the timing chain cover off did you use new gaskets ???

As for the sneaky tool :D I have always managed with a piece of string ;D

Title: Re: I think my engine is creating too much back-pressure :(
Post by: Darrell on June 21, 2010, 07:22:27 PM
All new gaskets were used on all the work done.

Doesn't seem difficult to start nor does there seem like any blue smoke at all.

My suspicions are due to a leak developing from the hole the dizzy sits in, took the dizzy out and replaced what looked like a perfectly good seal but did so anyhow.

Now it seems to leak from the oil cap.

I dunno but when I take the cap off when the engine is running, there seems to be more pressure in there than I think is right, but we'll see coz the sleaky tool will be serving two purposes ;)

How on earth do you use a piece of string to change guide seals/springs etc with the head still on?
 :oops:
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Pete126 on June 21, 2010, 07:52:34 PM
They all produce allot of pressure in the sump with both pistons moving up and down together [-/ are you sure the seal is O.K.

The Piece of string ;D Take the rockers off, the spark plugs out, rotate the engine till the pistons are at bdc feed in the string, rotate the engine towards tdc, this compresses the string to the valves and holds them in place :P P.S. leave some of the string hanging out of the plug hole so you can pull the string out :D
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Darrell on June 21, 2010, 09:47:03 PM
What is making me suspicious is it only ever leaks when I run at 60 plus...

Those ally bits eg the extended rocker cover...the castings are terrible! I had to clean-up the casting alot and check for true with water paper on glass.

Anyhow, cannot do any harm to test as much as I can as the more I know the engine the better. I have to confess the BIS I had could do 80, never leaked, never overheated so the lesson seems to be that they're probably as good as each other, just has to be set-up right etc.

About your piece of string.....you sneaky...... [-/

One thing, the Dellorto has a simple trumpet on it.
When cold it will backfire through the carb a few times when starting from cold.
I'm wondering if this is a clue I have ignored.

On a good note, she doesn't pink/pre-ignite any more and seems to have loads more power with the Dellorto on it.

I did about 200 miles this weekend, one tank of about 15 litres did about 150 miles so dont seem to be any worse off with fuel consumption.
Torque seems more as some of the local hills I could only do 30 up, now she'll get to 40.
I still think it gets a bit too hot though as I had to run her with the engine lid open on the motorway, the tell tale for the excess heat is she starts to pre-ignite again, open the lid and it goes away.
Admittedly I'm running at 65 and I'm going to have a look at that gearbox, I might be running a BIS diff. I think that wouldn't help.
I thought I had a rubbish gearbox because it wines in fouth, enough to do my head-in but consulting the manual it seems end play might be at fault, so two jobs to do on the box makes it worth taking-out  :oops:
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Allan on June 21, 2010, 09:48:46 PM
Hello again,
Darrell the hose you put up looks like an extension for a compression tester.
Rusty's uncle. You can make a leakage tester using an old spark plug and an Aro coupler. Knock the guts out of the plug and braise the Aro coupler onto it. Then apply compressed air at about 100 psi and listen as described. CAUTION. As soon as you plug in the air it will try and force the piston down so make sure you are on the compression stroke , piston at TDC. You will have to stop the engine from turning so car in gear brakes on. If you have any question give me a call.
Allan
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Allan on June 21, 2010, 10:01:18 PM
Sorry Rusty's Uncle I forgot to add that the bought testers have a gauge on the that measures the % of loss. You zero the gauge before use and the plug it in. You need at least 100 psi to get a decent reading, remembering that most compression pressures are higher than that. If you are ever near a piston engined aircraft with the engine cowels of have a look as some engineers write the leakage on each cylinder for future reference.
Allan
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Darrell on June 21, 2010, 10:03:53 PM
I was thinking the hose would be a short-cut to what Rusty's doing :P
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Pete126 on June 21, 2010, 11:36:15 PM
The only way it can spit back through the carb is if the inlet valve is slightly open when the spark plug sparks, What this means is assuming the camshaft timing is set correctly, that the ignition timing is out, If its too far advanced this would cause the engine to overheat.
If It was me having this problem I would take the 123 off and stick the standard distributor back in and see if the problem goes away :)
 
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Rusty's Uncle on June 22, 2010, 06:51:08 AM
I just liked the idea of a simple device to put pressure into the cylinder and listen for leaks. Reminds me of tuning twin SU carbs by listening on a short piece of pipe at the inlet  ;D
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Darrell on June 22, 2010, 08:19:29 AM
Triumph TR4 and Land Rover with Rover 90 - 6  with twin carbs, listening to get the balance right? That sort of thing Rusty? My dad spent hours balancing those car's carbs  :oops:

The more I do, and the more I think and observe about the way the bug runs, the more I think 123 got something wrong.

I have resisted taking the 123 off, because I've really wanted to not have points issues, but will take the 123 off and test run her for a week :oops:

On another note, while sneaky tools are in mind.

Is there a way to hold/extract the cam followers whilst replacing the cam shaft, or is it a head off job only?
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Pete126 on June 22, 2010, 10:19:54 PM
Its a head off job on the air-cooled because the push rod tube seats are located in the head :( on the bis you can fish out the tappets buy removing the rocker cover.
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Darrell on June 23, 2010, 08:14:02 PM
Now back to running poits...so we will see.. :oops:
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Darrell on June 28, 2010, 03:17:19 PM
Odd thing, never ever seems to pre-ignite with the points.....

I noticed the aluminium rocker cover has a very small hole for the breather, way smaller than the original tin rocker cover. I've made it alot bigger (9mm) but it still is alot smaller than the original breather was.

Thinking of whipping it off and trying to find a bigger holed fitting for the breather :oops:

Just don't know where to start looking for a bigger fitting....
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Pete126 on June 28, 2010, 06:40:06 PM
Get down to the plumbers merchants I'm sure you could find some 15-22mm compression fittings that could be adapted and screwed in to the casting if you drill and tap the casting.
Is the engine overheating now you have taken the 123 ignition off ???
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Darrell on June 28, 2010, 09:51:13 PM
Hi Pete,

No doesn't seem to overheat at all. I did an uphill splat back from dropping Gilly off tonite, got to 70 and held it with no problems at all.

I'll definitely go see what kind of fittings they have that can be adapted. I have some BSP taps so should be able to drill and tap a bigger hole [-/

I think that's why i thought it was making too much back pressure...it blew it's dip stick out! :-X
Title: Re: I think my engine is creating too much back-pressure :(
Post by: bis13 on June 28, 2010, 10:16:57 PM
i have blown out my dipstick a few times and also have an after market alloy rocker cover all i have done to combat this is change the dipstick rubber and wind a bit of tape around it so it fits tighter! you can also bend the dipstick so that it sits under the engine tin where the thermostat flap drops down and stops it popping out...
Title: Re: I think my engine is creating too much back-pressure :(
Post by: Darrell on July 04, 2010, 08:18:22 PM
*update*

Took the car Southampton to Torquay area (Devon) and back today.

Uphill, downhill whatever, never a pre-ignition heard other than a deeper throaty-er noise from that gorgeous Dellorto and exhaust.

Some of the hills got quite scarey, one needed the car to be in second!

Oil stayed in the engine so I'm very happy.

It seems I am better suited to points than 123 ignition but am open to anyone teaching me what I'm doing wrong ....
The wiring for the 123 is still in place and now lives in the boot as a back-up.

Lost an exhaust bolt....scratched head on the side of the road and found one of the engine to gearbox bolts will work....better replace that.
I'm not looseing another exhaust bolt again so the locking plate bit i see on e bay will be purchased or wire-locking the nuts etc

As a point of interest I will be putting-up fuel consumption figures soon as I'd like comments , bear in mind I have a fairly heavy boot and try to sit at between 60 and 70.
Wouldnt be a bad idea to compare them to other air-coolers/bis's
The published figures...I dunno...