Club126UK
Fiat 126 Chat => Fiat 126 Mechanical Problem Solving => Topic started by: Darrell on May 14, 2010, 08:58:23 AM
-
I've come to the conclusion my air-cooled over-heats.
I've tried all variations of ignition timing, the big hose is in place, the fanr seems ok.
Now my timing light has quit on me :(
Any ideas? I thought it was a carb thing but changing the carb hasnt helped.
It starts to 'pink' up hills when she gets too hot and she looses power :(
any ideas?
-
Are you running the standard, or electronic ignition?
-
Electronic ignition
-
is the thermostat working ok?
-
I took it off completely, because I thought maybe it was sticky :oops:
-
I would try a standard distributor and see if it helps. I had so many problems with my electronic ignition, I can`t be bothered with it any more, and gone back to good old points.
-
I am beginning to wonder if you are right because I never had too many problems on points either :-
-
Seems the oil light issue is associated with this over heating because it only come-on when it is too hot, which kinda makes sense... :(
-
In the 123 ignition handbook it says use curve 0 or 1 for the standard 500/650
It also says maximum advance is 28 degrees at 3000 rpm
Acording to my 126 handbook it ways static is 10 degrees, and centrifugal is 21 degrees
So now I'm confused
Does that mean standard they advanced 31 degrees? or is that a maximum of 21 degrees
In either case the numbers don't match so I'm thinking Mr 123 has a trick up his sleeve I dont know about :oops:
-
Where's that thread on setting valve clearances? :oops:
It's ok found the manual in the subscribers downloads :)
-
have you checked that your fan is not bent up as the blades can be bent and stops it from working 100% also make sure that the deflector is inside the tin work as if that is missing it will not guide the air correctly to the head the only time i have had any problems with over heating on an aircooled is due to the fan not turning properly.
you do mention that your oil light comes on is this straight away or after a while as it could be that the oil pump is not pushing oil around and the heat is coming from this?
-
I had alot of it apart this weekend, thought I'd check the fan and that seems fine and spinning the altenator by hand it is free and unobstructed, all blades in place. The deflector is in place. I've welded-up the hole where the air cleaner was.
The oil light only comes-on when it is hot (running for a while)
I checked the carb joint and that seems good so don't think she's running lean.
I tried different curves on the 123 ignition, but no matter which one I use, it ends-up in the same result, oil light on and pinking up hills.
I am beginning to suspect lubrication and will strip it completely this weekend, check bearings and oil pump :(
-
Extract from a VW forum:
vw engines were designed to run on unleaded from very early on inthe 70s - I remember having my Bay and every Tom Dick and 'Arry was trying to sell the latest lead replacement gadget to unsuspecting VW owners.
The main issues was how hard the metal used to make the valves was. If you wanted to, you could replace your valves (or the whole cylinder head) so that the valves were made of a more hardened metal. Also, the unleaded fuel combusted at a slightly different moment compared to leaded, so adjusting timing would help this - avoiding pinking.
By the 80's I think all cars were able to run on unleaded without any issues.
I wonder if not running an unleaded head could be the problem? :oops:
-
I had a similar problem with pinking, having installed a 123 ignition. Set the engine up as described inserted the new 123 distributor, set it till the green light just went out. All seemed ok at first, then would not tickover and driving at 30mph with Kangaroo petrol. Finally checked the ignition timing all ok threw the strobe out of the garage and timed by listening, running a lot better. Checked the timing usinig the strobe and the timing mark at tickover is 20 ish degrees before it should be, but the car is running well. Still set on number 1 curve. No problems with over heating or oil light comming on.
Ralph
-
On my way back from the allotment a little while ago I saw the Snap-on guy and bought another timing light...don't ask how much, but anyhow put it on and it was a little too advanced. The timing light has a knob on it to set the degrees of advance thus I assume one would be using the TDC mark and not the 10 degree mark if one were to set the knob to 10 degrees.
The idle seems a little slower now and did retard it a bit but the frightening thing was how far the ignition advances when reved.
I took the timing light over to about 60 degrees and thats kind of where it is when revved...seems way too far! :-X
-
Anyone ever checked their oil pressure? :oops:
-
Cracked the 'pinking', on setting 0 on the timing light the flash is at the 10 degree mark, on setting 10 degrees on the timing light the flash is at TDC which makes sense.
No more pinking and she runs good, revs easily, steady idle, no flat spots and I think no high temperatures however .....
I think it's done a bearing as the oil light still comes on on idle when she's warm :(
Engine out this weekend.... first check on oil pump then bearings...
Going to sort out the end play on the gearbox at the same time and do the disc brake conversion [-/
-
Maybe a silly question Darrell, but have you got the engine running at the correct idle speed 850rpm ???
-
It just sounds about right for an Idle :oops:
-
The reason i mentioned it is at Retro Rides last year although your engine sounded as sweet as a nut, the tick-over was a little low ;) try running it up to temp and adjust the fast idle a little until the oil light stops flashing. If there is not any serious rumbling noises coming from the bottom end it should be O.K.
-
HI yes I upped the idle alot after that because it was way too low, and sitting in traffic with the lights on it would kill the battery :oops:
-
Pete so if the oil light comes-on at idle when she's warm she'll be ok?
-
NoNo what i meant was adjust the tick-over upwards till the oil light goes out ;) You really could do with a tachometer to check the RPM at tickover once its setup correctly if the oil light is still flashing then you need investigate further and check the oil pressure switch and then the bearings.
-
Hi Darrell , you may have got the overheating sorted now but I did think of your problem when I was stripping the scrapper and when I removed the rear side air inlet vents they were partly obscured by the foam seal that had shifted. [-/
-
I'll have a look at that this weekend Rusty [-/
I'm going a bit crazy here, I've ordered new bearings new oil pump, the fancy 4 litre ally sump, the ally extended rocker cover, a new thermostat and a few other bits and bobs. The idea is to get cracking on it this weekend and solve the oil pressure problem once and for all and add extra cooling.
I've wanted to upgrade the sump for a while now and the rocket cover and figure the extended one will give bigger volume on top of the head therefore reducing the amount the gasses can be compressed...we'll see if there is any merit in the theory however the bigger block of ally with fins is bound to give-off more heat.
Once the oil issue is sorted it's off to the local dyno tune bunch to do a tune-up, make sure the mixture and timing are 100% right according to a tuning guru.
I'm not certain about a horsepower test with fresh bearings in her, perhaps i'll do that another time but with a bit of luck any overheating will become a thing of the past [-/ If all is good and I'm confident the issues are gone, I might ask for a little test with not too many revs :P
-
The offending item...
-
.
-
is that the white metal thats been worn away in one part more than the rest? thats a bit spooky as why did it happen in the first place? or was it coupled with the problem of no oil pressure re the washer mix up..
-
I dunno, I think I got the washers wrong when I put it together this time as before she had 40psi even on idle, I checked it with a mate's pressure gauge, which he's now lost! >:(
It looks as though about an inch has been simply scraped-out, the piece, virtually intact but a little mangled was in the sump.