Club126UK
Fiat 126 Chat => Fiat 126 Mechanical Problem Solving => Topic started by: bobblehead on March 20, 2010, 07:37:33 PM
-
can anyone explain this :
had rac man out yesterday, said pump wasnt pumping and i had a air lock in system, he recccommended after he had had primed it with his diaphram pump, that i changed out the pump for new , and fitted a inline filter so i could see if i was getting fuel and it was being pumped though .
anyway i did all this, then tonight after driving and parking up....... car wouldnt start again ??? plently of fuel in the inline filter ?????????????????
pulled a pipe off the pump cranked over and nothing????? nothing being pumped????????
with absence of a hand diaphram pump, we aited and waited... then after 30 to 45 mins wait cranked with choke on full and pedal and it went ???????????????
anyone any ideas????
please?
-
It does sound as if there were bubbles in the fuel line which usually occurs when the engine is hot. Maybe the return line from the carb is blocked... or it could be just the fuel pump dying. Have you noticed an increase in fuel consumption or leaking fuel from somewhere as air might have gone in where the petrol came out? Or the fuel line might be bent somewhere and isn't allowing enough fuel through.
-
car runs great .. fuel pump is new .... car drives and pulls great .. after a drive and a park up.. return to car .. no fuel being pumped from the pump ??? no smell of fuel, cant see or smell a leak. from anywhere
plenty of new clean fuel in the new clean inline filter ?
fuel lines not kinked or caught anywhere ... could it be fuel cap is loose and drawing air? ???? .
but why would car run great , then suddenly this????? i changed the pump for a new one yesterday ??
even measured push rod with old one i had and it was same size??
so that not worn ... anyway why suddenly work and run great then not start or pump fuel ??? its crazy ?
-
I have a similar problem, when the car is running normally say 40-45 mph all is OK but push it it then cuts out then in. Checked the fuel line and there are bubbles all the time coming from the tank, all seems to be sealed have not been able to find out how the air is getting in, think there may be a crack in the syphon tube within the tank this would allow air into the fuel supply.
Ralph
-
Well another thought maybe then is that there's vacuum in the tank. Check to see if it pumps fuel without the fuel cap on. This may help but a blocked breather pipe could cause vacuum as well.
-
thanks for your responces .
ok, will try that cap off sernario ....
anyway just to say , its does run great dosnt lumber and pulls up hill .
also you can see no bubbles in the inline filter , unless its happening whilst im driving??
keep you posted ..
-
this was a constant problem with mine, have you checked the tank for rust?.. mine were baaaad, put extra filters on and everything, back then they were hard to get hold of but a new tank could be the answer?..
also i think there's an electric fuel pump available? i know nothing of this though
-
tank is fine ... may consider electric pump at this rate .
-
I've all the same problems as you except mine wont even start now :( im going though everything thats been said on here and also considering an electric pump and found this http://www.webcon.co.uk/Downloads/2009-Jan%20WFP502.pdf
-
you both have knackered carbs don't you??
-
i think that is wat its gonna boil down to!
have a look at this:
http://cgi.ebay.co.uk/YAMAHA-YZF-R1-1999-ENGINE-GEARBOX-ETC-5JJ-4XV_W0QQitemZ200453275140QQcmdZViewItemQQptZUK_Motorcycle_Parts?hash=item2eabf23e04
might help with our engine problems im very tempted to get one!
</4
-
i have 2 x fiat 126 bis, and have same problem on both, so going to nip in bud and get electric pump
-
i have 2 x fiat 126 bis, and have same problem on both, so going to nip in bud and get electric pump
cooool, let us know how you get on, soon they'll all be doing it [-/
kudos requ'd
-
i have 2 x fiat 126 bis, and have same problem on both, so going to nip in bud and get electric pump
Did it work then???
-
Is the pump pin too short or the gaskets too thick?