Club126UK
Fiat 126 Chat => Your Restorations => Topic started by: GTMaster on November 05, 2008, 05:46:23 PM
-
Here's my Olive Green 126. It's been off the road for sometime, but it still started up like before :) Funny thing is, everything still works on it, just not all smoothly. I plan on putting it through a complete restoration to factory spec. I have some of the needed funds, but my biggest problem is lack of tools. Parts aren't expensive, but tools are :) So, it'll probably be early next year that i'll be getting into it.
For now, i've finally found space in the shed. It's been out under the stars since the roadworthy expired. I hope that now it's in a dry place that it'll stop rusting :) As you can see where it's painted there's rust, and under the carpet on the inner arches. The rest though is fine. It'll get a new paint job, fixed up interior, front suspension needs a total overhaul. The engine on the other hand runs fine. Just a big end crank seal is needed to stop the oil leak. The rest is just fine tuning of the carb and ignition points, valve clearance etc. The gearbox needs a check. The half axle rubber bells are ripped, the clutch will be checked, but that was changed not long before we stopped using it. All in all a big project, will post more pics as time progresses :)
(http://club126uk.co.uk/forum/userpix/714_Shed_1.jpg)
-
(http://club126uk.co.uk/forum/userpix/714_Front1_1.jpg)
(http://club126uk.co.uk/forum/userpix/714_Rear1_1.jpg)
I tried everything to stop the rust. I used PU foam in the holes (cavities more like :) ) and loads of paint. I knew it would only be a temporary solution, cos that wouldn't be the way to go. I still have the number plates, just that it's been temporarily 'off the road.'
-
(http://club126uk.co.uk/forum/userpix/714_Archfront_1.jpg)
(http://club126uk.co.uk/forum/userpix/714_Boot1_1.jpg)
(http://club126uk.co.uk/forum/userpix/714_Interior1_1.jpg)
Le enterior :)
The powerplant
(http://club126uk.co.uk/forum/userpix/714_Powerplant1_1.jpg)
-
Good luck with the project! What year is the 126? from the look of the interior and the bumpers ita an earlier model?
Just have one idea, when you go restoring the inside of the car, try some other colour other than blask (soo booring and sad...)
heres an how id go with an old school style... :D ::
(http://img227.imageshack.us/img227/9708/796jb6.jpg) (http://imageshack.us)
(http://img357.imageshack.us/img357/9713/795ka8.jpg) (http://imageshack.us)
(http://img83.imageshack.us/img83/4319/794rw8.jpg) (http://imageshack.us)
or try some of the other orig trim colours... (you did say youre going factory spec, so this is, in my opinion, the way to go....) :wink:
(http://img385.imageshack.us/img385/8995/pa3hpo3.jpg) (http://imageshack.us)
either way you go about this, best of luck! :smt023
-
im loving the green colour! good luck with the resto.. keep us updated.
thats the interior in my new deville i brought, brown cord cloth its horrid its gone all dark i should imagine it looked nice in its day thoe.
does anyones push button washer work? and how affective are they>??
-
does anyones push button washer work? and how affective are they>??
Mine has the electric motor pump, works ok...
im surprised fiat didnt use the principle used on the vw bug, in the bug, air pressure from the spare tyre is used to push the washer liquid... simple yet effective solution, mugh better than that button...
-
Yeah those vacuum operated window washers do work if the button isn't broken. Mine is, so i get more washer fluid on the floor than on the windscreen :)
It's a 1986 FSM. Just wondering: it's the basic level trim version, but the rear bumpers have space for the reverse and fog lights. Did they come with bumpers without the cutout for the lights? The bumpers i know of are:
Chrome, these plastic types which were on the 1989 even some 1990 models, BIS bumpers and the big type bumpers(1990 onwards). Any other types?
Thanks for the tips CroBis, though i'll probably stay with the vinyl. I don't think i'll have that much money to change the trim.
About the trim: has anyone ever taken out the roof carpet? Mine's sagging in the middle, which takes away alot of headroom. Doesn't seem too difficult, but if someone has a good technique, then i'd be obliged :)
-
As far as i know there were 3 types of bumpers; the big plastic ones on newer aircooleds and BISes, the metal ones (Cheaper saloon modells) and the ones you have (better trimmed DeVille models) this applies to original FIAT 126es, dk about polish made ones....
as for the headlining,, i just ripped mine out, though its easier on the bis (using the rear boot door)... shouldn't bee too difficult....
-
i'd love an early 126, they started in '89 here, theres no variety at all:(
as far as fixing the ceiling, i found out you can move the whole thing around a bit when mine was falling down at the front (it had moved away from the edge and wasnt being supported anymore), you can probably push it around so one side and the front fall out then slot the rest out after that, but if you just want to glue it back up, get a hypodermic needle from a chemist or somewhere, get a drill bit that's no bigger than the needle, then drill holes where you want to glue and inject the glue up through the holes. if done right you'll never be able to see the holes, as theyll be too small (less than a mm if youre good).
in most cars you dont need to drill through, you just stick the needle through, but a 126 ceiling is really thick, you can try just sticking it through first though, itll have a better result.
obviously youll need to choose a watery glue, preferably fast drying, because holding your arms up in the air for any length of time isnt so comfy. but above all it needs to be pretty strong.
good luck!
-
Just thought i'd write something, just that i haven't been able to do much (it is quite cold afterall :) ). I'll post pics of it soon, since then i've disassembled the lights,bumpers,some of the interior, nad door trim. I've ordered body parts from Axel Gerstl, and hopefully they'll be here by the end of the month. I think the hardest part of this restoration will be the repair of the bodywork and painting. Replacing missing trim bits and other accessories won't be a problem, and overhauling the suspension will seem to be an easier task than this. Anyway, waiting for the weather to warm up a bit :)
-
Pics will be coming, but this weather doesn't seem to warm up :) Since then I've totally taken out the interior,except the dash (the roof lining i ripped out ,it was very brittle, and hopefully i'll either be able to find a new one, or make another one). Took off the bonnet, boot lid, door seals and started 'hole hunting' ;D
Quite a lot of rust, and got rid of most of the PU foam that was in the holes. The inner door sills don't look too good, but it will be getting new outer sills :)
Bought some tools, and some time soon i'll be getting a MIG welder.
-
Hi,
Haven't been here for some time. Here are some fairly recent pics ('bout 2 weeks ago.)
-
Since then I've bought a MIG welder and got into doing body work. The front I've finished (just minor welding here and there), so no holes there :)
Now on to the rear right wheelarch. Real nasty.
After that I'll be pulling apart the whole front suspension. There's some holes right next to the upper arm on both sides.
Then it'll be over on to the fenders and sills. That will be the challenging bit.
-
keep up the good work [-/
-
Well, done quite a bit since then. The front right fender is off, and so is the right sill. Just rebuilding the bottom half of the inner sill as it was totally corroded. The front right suspension is out. Since i'll be pulling apart a lot of things, i'll be replacing a lot of parts, whether they're good or not. The brake line nut was so tight, i pretty much ruined it, but i'm sure i'll be able to tighten it properly again.
Finished the rear right wheel arch as well. Just can't wait to get it going again, cos i really,really want to drive it :)
-
Thought i'd drop a line. The bodywork is finished and is ready for puttying, though that'll come later before the respray. I will get photos it's just that i need to make some room in the stable to get any worthwhile shots. I thought i would also put in a little rant: i'm finding it fairly difficult to get parts to the 126. i thought there would be more new parts available at a more afforable price here in eastern europe but it seems that the 126's are going out of fashion here as well.
I'm onto the front suspension. Have everything for it (bushes, ball joints, wheel bearings, shock absorbers etc) just need to get the right hand side kingpin changed. I couldn't find a left hand wheel hub so i bought a renewed one (b****y expensive). I've taken off the leaf springs and will pull that apart as well.
Just thought i'd also ask you guys how difficult is it to get parts for the 126's in the UK? I wouldn't've expected to pay the amount i've already paid for the parts.
Anyway, the suspension on the car will be [-/
-
Finally got round to taking photos last night. I know they're not that good , but there just isn't enough space in there. I know the paint job and welding looks messy, but it will be repsprayed and the holes and bumps caused by the welds will be filled in and will be smooth.
The wheelarches and places that were sanded down on the chassis were painted and got covered with underbody spray.
-
The suspension has been fully restored, i only need to adjust the wheel bearings, tighten all the nuts when the car will be lowered and the rear left brake line (on the trailing arm) has to be replaced.
-
Interior work: front inner wheel arches, inner sill and the plate where the shock absorber bush sits had fallen out (rotted away). The white stuff is acryilic sealant.
-
More...
-
More bodywork, now with the new arches :) The markings were painted on while i was waiting for the steel to cool while welding. It'll be resprayed anyway...
-
Left sill; inner front right wheelarch; above fuel tank on the inside
-
The top two spring leafs were broken, so i got a complete one from the wreckers and replaced the top two. Unfortunetly i couldn't get any of those plastic sheets that go between the leaves or new brackets or the bolt with the rubber top that holds the whole thing in the middle either. Each leaf was sanded, and greased thoroughly with graphite grease.
-
New ball joints and tie rods (tubes), king pins, bushes, rubber brackets that hold the leaf spring to the chassis, new brake drums all round, new brake cylinders all round, new front wheel bearings, new brake lines, new rear brake shoes, new shock absorbers all round.
-
More..
-
Resprayed fuel tank (top looks c**p but the bottom part of the tank looks better), starter motor is pulled apart and will need two bearings and the rubber that covers the arm that pulls in the cog wheel.
-
The left hand side turned out to be better than the right. I really don't have that much space and the floor is dirt and sand not concrete...
-
Engine... ohne auspuff :)
-
nice job you are doing there [-/
-
KEEP GOING! Another fiat will be re-born soon. Niiiccee :)
-
I can only say, what has already been said.
Jo munka!
-
Köszönöm for the kind replies :) I am planning to get to work on it when the weather warms up a bit and also go to the local wreckers next week to have a look around. The guy there has quite a lot of bits and pieces so i'm sure i'll be able to acquire most of the things needed.
-
Just a minor update: got a few bits and pieces so won't be getting anything until i start putting it together after painting. Got another drivers seat which i'm happy about as it looks like new :) Stripped the old seat kept the springs and covers with the sponges.
Stripped the doors of the windows and locks (locks will be hard to put back in i think) and also put tar onto the floorpan where it was repaired. The only other thing i did was remove the gearbox, cleaned it and inspected what needs changing. Drained the oil which was clean but not alot :o The new half axle rubber boots i have but the input shaft is wobbly so looks like i'll have to take off the bell housing. Needs a new release bearing and release bearing fork shaft. I also intend on changing all the seals.
-
Pics...
-
Box
-
youve done alot already!
whats them black stuff? seam sealant?
Chris
-
That black suff is this tar insulator that they use in the building industry to insulate bricks and concrete. They come in big rolls and have plastic on them, which i think helps adhesion. I measured the size i needed to cover where the factory insulator was, since i had to cut it out when repairing the rust. I used a hot air gun to melt the underside of the tar strips, pushed it onto the metal so there wouldn't be bumps or air underneath it, then let it to cool. It's stuck on there well so i hope it won't come off :)
-
That black stuff is called Bituthene. I use it a lot at work for damp proofing underground stuctures like cellars. First paint the surface with a bitumen based primer maybe thinned down with a little solvent, then the Bituthene bonds on contact and believe me it's NEVER coming off again, so be sure to get it right first time :oops:
-
Thanks for that, didn't know what it was called. I did paint the metal underneath it but it's just basic glossy green paint.
-
Thought i'd "fill" in on what i've done since. Exactly that: filling. I can't say i'm a pro when it comes to welding but puttying requires the talent of a sculptor :) There won't be the big gaps between the front fenders and the front panel as i had to spot weld there as well. Anyone know good tips when it comes to puttying?
I removed the gearbox and since have reinstalled it. I changed all the seals, fitted it a new input shaft and bushing, release bearing, half axle rubber boots, gearbox rubber mounts and filled it up with Agip 80w-90 oil. Also painted the remainder of the chassis and sprayed it with underbody spray.
Hopefully i'll be getting a new breather pipe for the petrol tank and will be able to fit it this week.
Just cleaned and resprayed the thermostat housing and used a hot air gun to test the thermostat (which seems to be in working order).
I really hope that i'll be able to take the car off the blocks this weekend and roll 'round with it in the yard. One thing that bothers me is that the steering mech has started to leak oil >:( So looks like i'll be taking that off when the car gets finished and will have to change all the seals...
-
Will have photos soon. Got it off the blocks and fired it up without the exhaust ;D :) I fitted the old exhaust back and went around the block with it without the doors on so it was a bit "breezy".
-
I was wondering whether anyone experienced something similar to what i did today. I fitted new shocks to the front and noticed that when the wheels are on the ground and i start to shake the front wheel i can feel something wobble and it seems to be the shock absorber . I've checked the wheel bearings twice, the kingpins were renewed so it came as a surprise. Hopefully it won't effect the driveability of the car...
-
yeah i had the same problem when i fitted a different leaf spring, rack, control arm and stub to the drivers side. I still cant explain it. At 55-60 kays the front end wobbles pretty badly. I drove it like this for about 50 kays thinking it was the leaf spring needing to settle but no luck in curing the prob.
The gearbox sh#t itself after about another 10 kays (not related i think) so i havent had a chance to road test the new shocks i put in yet.
sorry i cant help much and i hope you dont have the same prob. i'll be fixing the gearbox this weekend and hopefully road test and let you know
-
when you replaced the shocks on the front did you renew the rubbers and make sure that the bush was seated properly its very easy to forget the first rubber which sits under the body and betwwen the shock this can make it move around.
-
I suffered a simliar sound caused by an old set of shocks with worn thread. The nut could not be tightened correctly, as a result there was some play which cause the knocking noise. Ties in perfectly with what bis13 said. After checking that:
I assume when replacing the shock you simply unbolted te old then bolted in the new?
If not have a thought about anything else you may have unbolted/ rebolted in the process.
-
Thanks for the replies.
I renewed the shock's rubber bushes. It sits in a metal plate which i had to sand the sides off a bit (more oval shaped now) so it would sit properly into the top of the wheel hub.When I tried to fit it the plate didn't allow the thread of the shock to pass through enough so i could catch the nut onto it. I'll try and see if i can tighten the top and bottom nuts more, but i tried moving the shock cylinder itself by turning it and it doesn't seem to budge. I fitted new bushes in the wheel hub and leaf spring eye and i tightened the leaf spring bracket as well (new as well.)
If nothing else after the wheel alignment i'll just leave it as it is. I didn't notice anything when test driving it, but then again the tyres were fairly flat and it was a bit loud driving with the doors off :)
-
Test drove the car and the wobble was still there. Put it on the hoist (again) and found that the leaf spring bracket bolts werent tight. Then i noticed that the spring bolts/pins had pulled thru the chassis. I probably made it worse by driving it, but now i'll have to weld them up and try again.
-
Sorry to hear that, must be a pain to repair and a wheel alignment check may be needed just in case the suspension geometry changed. I bet you're a bit >:( right now ....
-
Not too p*ssed, just part of owning a 126, but i guess the accident didnt do it any favours. It really was a good car before it got nicked and in the 72 odd hours of ownership before it happened.
I cant wait to get my other 126 sorted so i can start driving it.
If you've renewed practically every rubber in the front end she'll drive like a beauty, once you get air in the tyres and a couple of doors of course. The one reservation i have about the std front end is the top a arm sits at a bad angle at std height and causes the wheel to lean positive on compression. Noy what you want really
-
Not much happened since. Just haven't had enough time >:( It's been primed but needs sanding and shifted it from the stable to the garage for the paint job. My only question is with the puttying and powder coating which has been haunting me: what causes it to just puff up and when pushed crack and peel/scrape off? It's as if there's an air bubble underneath it and the powder coating just doesn't stick to the layer of putty underneath. Funny thing is it only happened around the bits that was repaired (e.g. where the b pillar and sill meet) and luckily didn't spread further. If i had pics i'd show but it's been driving me mad. Hopefully the whole package will be painted this weekend.
The only other thing i did was do a compression test on it. The engine was semi warm and got a 9.5 bar reading for both cylinders. Any one else with something similar? The engine will only be pulled apart so i can change the seals, i don't plan on replacing valves or piston rings as it ran very well before being layed up in the front yard.
Also what i noticed on the engine with the exhaust removed is that it was running on a very rich mixture (black smoke) which explains why it had bad fuel consumption but ran well. Hope the servicing of the carb won't ruin performance as the carb that's on it at the moment is off an earlier model (Weber 28 IMB 100 i think.)
-
A. Did you key the surface prior to applying the bog? B. Did you use the correct amount of hardener? C. Was the surface clean before application? Not doing these would cause the symptoms you describe. Not teaching you to suck eggs btw
-
Thanks for the reply. You can teach me how to suck eggs in the painting/puttying department as i hardly know anything about it ;D
E.g what is surface keying? I think i used the right amount of hardener as it goes hard on the surface but beneath is a bit soft and doesn't want to stick to the metal/puttyed surface beneath. I talked to a paint shop keeper today so i think i know where i went wrong so i'll start from the beginning:
After welding i used rust remover on the repaired surface (where the spot welds were) because i knew i'd only be able to start on the paint work much much later on and didn't want to bother removing surface rust. What i didn't do with the surface after that was clean off the rust remover properly. I gave it a wipe with a cloth do get the dust off then applied a thin coat of rust preventing primer. Afterthat i used knifing putty on it. In the meantime the two component (hardener type) putty ran out so i used a small amount of single component putty, which when applied too thickly cracked, so i was careful with it. After acquiring some two component putty i started using that again. All went well till the first coat of primer. That was a different type, a much thicker type to cover up the spot welds better. This puffed up and could be peeled off. It was sanded down and refilled with knifing putty. Then came a layer of another type of primer that were used on the doors (turned out good , no problems at all). That puffed up too but not in the same places. That was sanded down, refilled and resprayed.
So after that short story it still came off in smaller quantaties though, which is what i'm repairing now. >:(
Car painters can throw stones at me for doing that :) (and as my signature says: "You need time for a good job but you need more time for a s**t job" ;)
-
Keying the surface means sanding with a 80-160 grit to get the bog to stick. Did you do this prior to applying bog? If your bog is still soft underneath, you either didnt mix it properly, didnt use the right amount of hardener or you applied it when it was going off. You must remove all traces of rust converter prior to starting any bog applications. I think your bubbling up problems may be starting from here. Filler putty can be used up to 5mm thick but knifing putty should be used just as a skimmer - 1mm max. Ive seen and done filler up to 10mm thick and it lasted but jeez the weight of that car went up by about 200kg once i finished - you dont want to be doing that to a little 126, stick to 5mm max. If you find that you need to go deeper than 5 it may be time to get the hammer and dolly out.
Difficult to diagnose without seeing it, maybe posting some pics might help.
This is how i would go about panel repairs - and painters can throw stones at me too.
Remove all paint to get surface down to metal, remove rust if any and plate, key/sand surface with 80-160 paper, apply filler bog if 5mm needed, knifing putty if less than 1mm needed. Once hard key surface with 320-600 paper and feather out the edges, apply 2PAC filler primer covering the repair area and overlapping by about 100mm in all directions, key with 800 paper feathering those edges and your pretty much ready for paint.
Of course there are books on the subject and the above is just a short description of a long tedious proceedure. Its all "live and learn" mate if you tackle these things on your own. Just remember that cleanliness before starting each step and adequate curing time will go a long way in avoiding problems. I like to go down to metal in my repairs as i once had a bad experience with bird poo stains coming thru my new paint as i only keyed the paint that time. Also make sure that all your products are compatible. EG you can use acrilic paint over 2pac primer, but you cant use 2pac paint over acrilic primer.
The 2PAC filler primer comes in cans and is very versatile - i once re'can'ditioned a whole car with a filler spraycan and got excellent results (here come the flying stones). Its sets really really hard and is a bitch to sand but leaves a very workable surface as long as you dont get it wet.
The way i see it - if you get someone to do the work for you it will probably cost 8-10 times more than if you did yourself, so you basically have 8-10 goes at this before your behind. Thats been my philosophy and it works for keeping me motivated.
Good luck with it - good to see your tackling what i consider the hardest part of building a car.
-
Thanks for the helpful reply [-/ I'll use it on a future restoration as i can't do anything about the puttywork now, which seems to have 'stabilised' but i don't want to do any puttying or painting for a while once the car's finished :P Keeping my fingers crossed for some good weather for the weekend. If all's well then it'll be green and i'll be able to take pics of it :)
-
>:(
Yes, never been so frustrated before. The guy who made the new head roof lining made it according to the old one yet it just didn't want to go in. So first one edge, then the other cracked and broke. So frustrated as it looks so good (beige carpet). Now i'm thinking about cutting it down a bit and just glueing it to the roof. I've searched the forum on roof lining topics and it all seems to be the same: no one has really successfully changed one before though many have just ripped it out of their cars :P I even removed the rear window thinking i could slide it in easier from there: no luck as it just ruins the edges of the plywood-like lining. I'm thinking about removing the windscreen and seeing whether it slides in from there...
After a few more attempts it just started to break everywhere... though i'm happy that the car's green and i've sorted the electricals :)
-
Hello all,
Finally managed to scan in more pics. I haven't given up on the car and it's looking good. Hopefully i'll get the roadworthy done this month or early next month. Still needs some minor work (bumpers fitted, wheels painted and new tyres need to be fitted as well as the mudflaps, rear windscreen, window washer and windscreen wipers.) I've put the engine together so i'll have pics of that too. I've got a new condenser as there are small sparks at the points (brand new points too) and i'll need to check the carb as i'm not satisifed with the idle (have to check the CO, some black smoke and stutters/stalls for a moment on acceleration) though it revs like mad :P
Have more pics coming when the car is totally complete.
This is when i pushed it out of the stable ready to go into the garage...
-
In the garage. This is where the prep work was done before painting.
-
Masking and puttying ( >:()
-
After the paint job. Not too good, and haven't got a full pic of the car with the doors yet. After the paint job i did the electricals.
-
Put the doors together (had problems with the window winder. Got so tangled up i had to get a new one from the breakers.) Also had problems with aligning the doors (only when fitting, pushed some paint off >:()
The right hand door lock was worn as i couldn't lock the door with the key. Got a new one but it was dodgy as i couldn't then open the door from the outside with the handle >:( So did some welding on it now it works fine :)
Then started work on the engine:
-
Well there were a few things with the engine: nothing left of the gasket under the cylinders :o and the inlet valves were totally worn. So bought 4 new valves (wasn't easy to find them) and took it to a place called dr. motor where it was skimmed and the new valves were put in (seats repaired etc.) The guides are still good and so are the springs. Nice and clean now :) Cleaned the block and the engine got new gaskets.(cyl head, oil sump, rocker cover etc). Changed the big end bearings too as they were all worn (the crankshaft journals are however like new).
Couldn't take off the crankshaft pulley unfortuently to check the seals and timing chain but no oil dripping so far. Had to replace one pushrod and the rocker adjusting screw as the hemi sphereical/ball joint part had broken off (cyl 2 exhaust rocker once jumped off the valve so i guess that's when it happened...) Rockers were sanded/grinded too.
Head is now on, so is everything else. In the meantime i painted the fan and other covers that i didn't do previously.
-
Changed the float in the carb as it was cracked in 3 places and had petrol in it. Changed the needle and seat too.
Put the interior together the rear seat got a new vinyl cover which looks good. Only thing left is the drivers side floor carpet (hope to get a new one) and put in the drivers seat and seatbelt.
Pulled the dynamo apart. Changed the brushes and bearings, had the collecter part machined.
-
That's all the pics i have now. The indicators and lights are fitted and working. Manged to break a headlight when fitting it >:( That felt good, :oops: it was an original Wessem type not the halogen type headlight. Managed to get another pair from the breakers but they're becoming rare.
Still have to repair the steering mech as it's leaking oil. Have a seal kit for it just need to take the steering arm off it first (getting a tool for that, also bought a torque wrench for the cyl head ;D)
Happy i've come this far, only the finishing touches remain. Stumbled upon a pair of Wessem rectangular halogen foglights in the shed. Having thoughts of fixing those and fitting them.... but that'll be something else for the near future :)
-
Hi GTMaster,
Must be nearly there, but I quess it's that last 10 percent that seems to take forever. >:(
Got the engine started yet?
Smallcox
-
Hi!
Yes have started the engine. Was interested in how it would start as i forgot to mention that i pulled the top half of the fuel pump apart as it was full of this dirt like stuff. I measured how much of the rod sticks out and put 0.2mm thinner gasket paper so i reckon fuel pressure should be good now (didn't have problems with it before though). As soon as it sucked up the fuel it started without a problem and runs good, just i don't like its idle. It seems to run smoother at a higher idle rpm, but i'll put it onto an emission test and adjust the CO. When i move the throttle a bit it stutters for like half a second before picking up rpm but then goes all the way, up and down, without a problem ;D 8) The engine gives out a puff of black smoke too when i floor it, so i'll still have to play around with it. Still need to change the condenser coil as it's making nice sparks through the whole rev range (from small ones to large ones). Tried three used coils with no luck. Got a new one just have to fit it and test it.
-
It's not unusual that the engine hesitates when you push the throttle,because theres no pump jet built into these carbs so go lean on mixture when the throttle is pressed :(
Good news your running, now how long before your on the road?
-
Yeah i know how it hesitates, sometimes played with it (pushed it to the floor suddenly then let go. It made a puff every time :P) This time however i move the throttle slowly and it doesn't rev up smoothly for a split second from idle.
Hopefully be complete by the end of the month. Though i've missed all my deadlines that i set up for myself so I won't be surprised if it will be on the road in the first week of October...
-
Deadlines are made to be broken,
October sounds Good
-
Question: has anyone experienced something similar?
Just previously tried 3 capacitators and still there were sparks at the points. Just put on a brand new one and I still get sparks ??? No idea why, the points gap is set to 0.5. Even if the gap isn't correct there still shouldn't be any sparks at the points.
The car started and revved well, though i think i may have run the engine out of fuel as after running for a good few minutes it just stopped on idle and didn't want to start. The gauge needle is at 0 though i thought it can go under 0 a bit (reserve?). So i'll put some fuel into it and start it up again tomorrow....
-
Managed a few shots off a digital camera. I will try to make some more in a more suitable environment soon :)
Anyway, i was very pleased when it all came together finally. I had problems with the oil sump as it had a slight leak. Took it off and noticed there was two places where the sump wasn't straight (has a slight dent in it as well) so when installing with gasket paste i manged to break one of the sump bolts >:( (turned out it wasn't a steel bolt either).Also had to refit the fuel pump with gasket maker too as the plastic spacer isn't straight. I still have a very very smal leak from the sump at two opposite corners. I'll just keep an eye out for oil consumption and fix it one day. Also noticed that the half axle rubber boot managed to pull out around 30kms before deciding to have a leak :P Looked under it the other day and no oil drip, so i'll change that it if it gets worse... (bought a new one in the meantime).
-
A few pics. The paint job didn't turn out too good on the doors. The middle is grayish and matt. Haven't tried polishing yet, but i had several attempts at the boot lid (which had it in a T shape) and it sort of came out (just now i can see the faint streaks i made with the polishing... :o) I'll be leaving till next spring as i can't be bothered doing it at the moment. I also manged to knock some paint off near the door pillar when fitting the doors... touched it up a bit but not as nice. All in all though i'm satisfied.
-
More..
-
The only problem i had at the MOT was with the brakes. The difference was only about 2% on each axle, just the machine showed that something wasn't true and didn't let it pass. They're brand new drums as well, so i thought it was strange. When testing on the first drive i noticed that the brake pedal pulsated slightly when braking, but thought it would wear away with use. So luckily they let me fix the problem and had it ready the next day. I took it to a turner to get them machined. He said two of the drums braking surface was a bit 'ripply' but surprised him it caused problems. I could feel the difference though when braking again: much smoother, pedal goes in slightly more now and still pulsates just slightly (handbrake also finally works now, 5 clicks and it stops the wheels dead :) ) Paperwork was a bit of a pain but got that sorted too. Only need a slight tweak on the carb to get a good CO at idle (high at the moment)...
Managed to get the steering mech. sorted, had to put it together twice as it leaked oil even with new gasket paper, so the extra gasket paste fixed that :D
Just did a wheel alignment on it too as i just threw the front suspension together. No wonder i could hardly keep the car striaght. Had a toe of +3 deg on the front right and +1 deg on the front left :P
Only the front right castor was a bit off (+6 deg instead of min. +8) but probably due to having new bushes. The rear toe worried me a bit as it was -19 minutes instead of +8 minutes on the left and -8 min on the right... i'll just keep an eye on the tyres as it handles well. The rear camber is larger (+3 deg.)
Only have the roof lining to do... i'll try to get good shots of the car in a better environment:)
Well that's it from me at the moment, very happy and managed to also reach 105kmh the other day, had a approx. 45km trip today so very pleased ;) **-
-
The paint job didn't turn out too good on the doors. The middle is grayish and matt.
I found my doors weren't too good on the 500 after the respray. I removed the doors and stood them upright to spray.I took the bonnet and boot off and laid flat, but they came up much better. I think its difficult to see how the paint has settled on the doors. Cars looking good, nice work!
-
Thanks! All the doors were removed and laid flat when spraying, the bonnet even got two coats :oops: The edges of the doors is fine (shiny) but the middle looks 'cloudy' ???
-
Hello, just had a look at my old thread and thought i'd end it properly :D
Well, I've done 1415km since its roadworthy and it's basically been used daily, mainly city driving without a problem since. It even started immediately in -10 deg. C weather so i'm very satisfied with it. Haven't been able to properly check its fuel consumption with all this cold starting and city driving (got around 13l/100km :-) but i do plan on going for longer trips once the weather gets better (very dirty now, haven't washed it since last November :oops:). As usual with winter weather driving, i get fogged up on the inside quickly and the water condensation on the inside of the window sometimes freezes as well :o
Anyway, managed to stop the small leak from the sump as it leaked after i had put gasket sealent onto it. It leaked from 4 bolt holes so i put some gasket sealent onto the bolt threads and it has stopped (won't be surprised to see a tiny amount between oil changes). Has gone through its fourth half axle rubber boot, checked the oil level in the gearbox and it was just right. Noticed a small leak from the gear linkage shaft on the gearbox (even though i changed the shaft o-ring seal) but there's a larger leak coming from the speedometer drive so i plan on changing that as it's coming out on top at the cable. Also replaced the oil filler cap as well (nice and shiny now). Just the other day when greasing the kingpins did i see a thin film of oil around the bottom lid of the steering mech. >:(, still better than what it use to be (the oil ran all the way down to the left outer ball joint :D)
Only needed to replace a headlight bulb (it was an old Tungsram one :() and the 75W bulbs I'm using are really good. Bought a pair of snow trays just in time for the snow fall at the beginning of winter but i still have damp carpets on the drivers side from the melted snow and water off my shoes in the rain(even under the drivers seat...).
Managed to sort the doors just before autumn. Got out a polishing disc and paste and attacked them. Took me a while and had to push the bugger a fair bit but they turned out nice in the end, especially the two doors. The bootlid still has some greyness here and there. Washed it, waxed it, cleaned the windows and interior, bumper sprayed the bumpers and used some tyre spray.... it looked like new 8)
Also bought a grease pump in the meantime as kingpin greasing is a frequent servicing activity. Bought some nice Lithium based 00 grease and in it went (just like having power steering :P)
Still need to make a roof lining for it. Was thinking of getting a 2mm thick sheet of polipropilane and glueing the carpet onto that (it's more flexible than the plywood i had originally and managed to ruin when fitting >:().
Will be doing a checkover at about the end of March (checking cylinderhead nuts, carb, valve clearances and points) till then it's **- Will have photos of it nice and shiny in the sun soon (hopefully if weather permits) 8) and will keep an update in pictures especially of the journeys i have in mind....
Well, the end [-/
-
Hi,just read whole story,! Great work,well done ..wish I had your skills! Car looks great..enjoy it,cheers,brett
-
Since then I've bought a MIG welder and got into doing body work. The front I've finished (just minor welding here and there), so no holes there :)
Now on to the rear right wheelarch. Real nasty.
After that I'll be pulling apart the whole front suspension. There's some holes right next to the upper arm on both sides.
Then it'll be over on to the fenders and sills. That will be the challenging bit.
How much cost in UK this new threshold and wing. at last foto. Thank you sry for english words ,hard to find technical phrases :)
-
Hi,just read whole story,! Great work,well done ..wish I had your skills! Car looks great..enjoy it,cheers,brett
Thanks :)
[/quote]
How much cost in UK this new threshold and wing. at last foto. Thank you sry for english words ,hard to find technical phrases :)
[/quote]
Hi,
Don't know the cost in the UK (i'm not from the UK), i bought these panels new from Axel Gerstl (the two new sills and two new fenders were 60 euro back then + postage, though it cost me more since i ordered the wrong fenders (which also cost more than the ones i needed in the end) and had to send them back at my expense...). The fenders are cheaper from 126fan.sk and another advantage is that their postal services are cheaper too. Though i do have to mention that i was 100% satisfied with Axel Gerstl's service (they also have lots of stuff for the 126 and Fiat 500).
The current prices at 126fan.sk are:
fender: 16.50 Euro
sill: 11.90 Euro
The current prices at Axel Gerstl are:
fender: 23 Euro
sill: 12 Euro