Club126UK
Fiat 126 Chat => Fiat 126 Chat => Topic started by: jumpinjacks on September 23, 2008, 01:45:38 AM
-
Hi all,
I am interested in a 126 Bis that I have seen, but I was wondering don't the water cooled's have many problems with them ( over heating etc )?
What are the common problems with them?
Also I would have to make a 225 mile journey to get it home, would it ( if its in good nick obviously ) make it that far ok?
I would prefer to go air cooled but tbo I can't find any for sale at the minute that aren't too may miles away from me.
Thanks,
Adam.
-
Hy.
As i said many times before, it all depends on the individual car (owner) if the bis was kept in a good condition it can make the journey easy, but if the previous owners didnt give a cr@p about it then youre gonna have some probs. my bis has been kept in a good condition during its lifetime and has never given any problems concerning the cooling system.
The main fault on its engine is the thermostat location, which makes the head gasket go, but this can be overcome by simply removing the therm.
it is my opinion that if you want a aircooled you should wait for one, cos i get the feeling that they're not so similar, but if the bis is in a good condition, id say go for it. simply make a few pauses on your way back, and leave the interriour heating on, which in turn helps keep the engine cool... :cool:
hope any of this helps... Gordan :wink:
-
As above as long as its been looked after theres no reason a BIS shouldnt be able to keep up with modern traffic (65mph) and make the journey with ease, Ive done a 200 mile journey in mine with no problems but they are like any other car -only as strong as their weakest part (my ten year old beemer has broken down more than my BIS in the last 6 months), but as with any car of this age I would not travel any where without breakdown recovery just in case!
go on just do it!! :wink:
-
You know you want to.... :D :wink:
-
Thanks for the replys guys :) . I will have to ask the seller a few more questions I think first.
-
What year is it? Mileage? Any pics?
-
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&ssPageName=STRK:MEWAX:IT&item=170265106742
-
Right I think I'm gonna go for it, but first do you think I should take some tools with me to remove the thermostat before I start the big journey? Or shall I try and drive it home with it still in?
If I should take it out then where abouts is it, and is it easy to take out?
What tools should I bring? ( I will be travelling up there by train so don't want to carry loads of tools )
-
theres no need to remove it immediately, its a investment in the future, so if the headgasket hadnt gone up to this point i figure itll last the trip home. some basic tools could come in handy, just in case ( + - screwdriver, 8, 9, 10, 11, 13, 17 wrench... and so...)
the best advice i can give you is like i said before, take a pause every now and then, just till you make sure it wont boil its kettle... :wink:
the photos on ebay are like 100x100 so hard to see anything other than the colour.. LOL... just give it a nice thorough inspection once there (brakes, steering, kingpins, tires, battery... and so on... :wink: )
best of luck :cool:
-
Also are the parts still available easily for them ?
-
A bit of searching to get lower prices, but sure. Mainly from poland and germany though :cool:
-
well, i can get most parts from local car parts shops... :P :P :P dk about the west countries though... :roll: :roll:
-
Not many Bis in Poland so parts are not easy to find there.
-
this is strange, all the parts i needed i found in my local shop (well except the rear main bearing :???: ) but clutch, fuel pump, air filter, brake parts, tyres... etc are all still avaliable. thought that the home country of the car would be better equipped.... well come to think about it, most of my parts were from italy...
-
Bis wasn't popular in Poland at all, parts that are the same on both can be bought bid Bis bits are tough to find. Not really sure why, I see they have a small following on fiat and furious bus not ofte seen on the streets or up for sale on Allegro. For example at the moment 4 bis for sale and about 200 aircooled.
-
:smt102
-
Also are the parts still available easily for them ?
most consumables are available from local motor factors (althiough often the have to order them,
any major stuff is usually available through online specialists or ebay.
Ive never not been able to find the bits ive needed!
-
What a nighmare that was, I got a train at 8:00am this morning and arrive at Cardiff statin for 1:30pm. Car looks cool so I buy it, and then 10 miles down the road the car starts overheating, and steam comes out the back and it starts juddering. So I have to pull in to the hard shoulder and wait for the free recovery to pick me up.
They arrive and take me to the nearest services where I phone the RAC, they send a guy out and he looks at it and then fills it with water and bleeds the radiator as there wasn't any water left in it and there was an air lock. So I try it again with him following me down the motorway, then he flashes me and the car is starting to overheat again :evil: , water is spitting out the back. I still hadn't gotten out of Cardiff yet!!!
So then he arranges for a recovery truck to come and pick me up to take me home back to Cornwall. So after loads more waiting at the side of the road and the recovery depot I arrived home at 10:00pm. What a long day!!!! :evil:
So now where do I go from here, now the car is home?
-
sorry to hear all that mate...
not sure what it is, cos it never happened to me, but open the rear boot, on the left side there is a cap, unscrew it, and start the car, as i understand it if you hear a cappuccino making sound on the filler hole the head gasket had gone. not sure about all this though, other members should be more informed...
-
I have just taken the car to my local garage, and they tested the head gasket. And it has indeed gone.
So I take it now I will need to strip it down and skim the head?
Wheres the cheapest place to buy a copper head gasket from?
-
And the guy that sold you the car forgot to mention this?? WHat an as**ole.. :???:
Dont really know anything about the headgasket problems, so youll have to consult with other memebers here.
-
Yeah I know, I moaned at them aswell. But they said that they aren't paying anything, as its sold as seen.
-
really sorry to hear this I had the same with mine after a month....
but lets focus on the problem-
you can get a head gasket (a full kit is a better idea as you can renew the inlet/exhaust gaskets as well) from you local motor factors, they will problee need to order it,
while you are waiting you can get the head removed, it will need skimming but this can be done by any machine shop or engine reconditioning centre, just get them to do it the minimum amount to to ensure it is flat and will seal properly..
it is possible to remove the head with the rear panel in situ but its much easier and quicker with it removed, just make sure the engine it support prior to start (a large piece if wood will suffice but a trolley jack is best.
apart from this its basically a nuts and bolts job (make sure you wd40 the sh*t out of the exhaust bolts for a day or so before starting) most of which is detailled in the workshop manual, if you need help just ask but its shouldnt take more than a week or so to sort it-
dont get disheartened it has happened to most of the BIS owners on this forum at some point and at lest if you fix it you know its right!
again-ask if you need any help!!
-
Thanks for the help there mate.
What can I do to try and stop this happening again?
Take the thermostat out I guess.
Someone said to me that some stuff called K-seal which is radiator sealant can seal where the head gasket is blowing aswell as it is that good. I do have some but am unsure whether to try it or not. What do you think?
-
Also forgot to ask earlier, which head gasket is better to get, a copper head gasket or a normal one?
-
I dont think they came with a copper one but I'd go for the most expensive which should be the copper one then at least you know you havent got to do the job twice as for the sealent leve it do it the job the right was it it would be a temporary fix.
as for preventative measures the thermostat is a good start apart from that just enusre you bleed the cooling system properly and make sure the cooling fan is working as this was what cause mine to shag its head in the first place.
-
Sorry what was that about the sealant? As I think you had a typo.
-
basically dont use it- its a temporary fix which could cause more damage in the long run, do the job properly and then you know you can rely upon it.
-
Yeah thats what I thought. Gonna order head gasket tomorrow
-
On a side note, here when we buy a car, we sign a standard car buying/selling contract, and one of the statements is that the buyer can return the car and get a full refund if there is something wrong with it (within two days). Dont know if you guys have this, but it could have been usefull...
-
Sorry to hear about all your probs but as others have said it has happened to all us Bis owners. When I first bought mine I drove it from central London to the midlands and it started to overheat, mind you it got me all the way home, 120miles, and as I pulled on the drive the rad cap blew off and water went everwhere! :cry: Turned out the fan had stopped working and on closer inspection one of the head studs was snapped so the head wasn't sealing properly. However, now it runs like a dream, so if you rebuild you will know what condition it is in and you can keep on top of it and in the end everything will be OK. Also you can get a thermostat kit from Ricambio that moves it from under the engine to on top of the head but it is expensive. Have fun! :D
PS you bought the best Bis colour but them I am bias!
STUEY - how are those Burners! :D
-
Wish they had that here, it would be ideal.
Just been to my local motor shop and they do have a head gasket set in stock but it is the standard one, and I want a copper one really as I take it they last alot longer.
So anyone know where I can get one as its gonna have to be on the internet?
-
Sorry to hear about all your probs but as others have said it has happened to all us Bis owners. When I first bought mine I drove it from central London to the midlands and it started to overheat, mind you it got me all the way home, 120miles, and as I pulled on the drive the rad cap blew off and water went everwhere! :cry: Turned out the fan had stopped working and on closer inspection one of the head studs was snapped so the head wasn't sealing properly. However, now it runs like a dream, so if you rebuild you will know what condition it is in and you can keep on top of it and in the end everything will be OK. Also you can get a thermostat kit from Ricambio that moves it from under the engine to on top of the head but it is expensive. Have fun! :D
PS you bought the best Bis colour but them I am bias!
STUEY - how are those Burners! :D
I think I am gonna just take the thermostat out tbo.
As with the fan, I am thinking of wiring it up to the ignition so it comes on as soon as the engine is started. My friend done this to his beetle and says its loads better.
-
I think I am gonna just take the thermostat out tbo.
As with the fan, I am thinking of wiring it up to the ignition so it comes on as soon as the engine is started. My friend done this to his beetle and says its loads better.
Or you could wire it up to a switch, so you can turn it on when things get hot. Theres no need to have it run constantly (without a thermostat and the fan blowing itll take ages to heat the car up, its noisy, and it takes a lot of power from the engine....)
-
Getting the little babies home can be a drama -my purchase involved an unexpected night in a hotel.........
-
What is the differnece between a copper head hasket and a normal one ( apart from what its made out of obviously )?
-
they are obviously tougher, normally thicker as most cars that are tuned tend to have had the heads skimmed and much more expensive , also quiet hard to find for the bis .
-
http://www.ferriday.co.uk/copper/copper.shtml
If you can't find anywhere to get one, this could be a solution for the ultimate in head sealing. I haven't ever tried this, but this company has been around for some time and has a good rep.
-
I got a copper one from RICAMBIO, but you have to buy a whole set and it is expensive. However, this was a long time ago and not sure if they still sell, give them a call:
http://stores.ebay.co.uk/Ricambio-International-Ltd
-
the other alternative is if you cannot find a copper head gasket just buy an aircooled 126 they are so more robust ,, i am only joking dont all start! lol
-
blah blah blah... then why are there way more bises than aircooleds?? (here i go... :D :D ) dont listen to him... :D :D
-
I have a BIS and an air cooled there are advantages to both.
Air cooled seems easier to get bits for. Like performance bits.
-
I've ordered a copper one from axel Gerstl now with other head set.
Hopefully get this thing back on the road.
-
Hi all,
I was trying to strip the head earlier today, but it seems a right pig of a job compared to what I thought it would be like. The exhaust is a sod to get off, its still on at the minute as I've given up for a bit.
Does anyone have a step by step guide or something to taking the head off? I have the manual on cd but that doesn't help really tbo.
Also I took the thermostat housing off to drain water out and have a look, and it didn't have a thermostat in there. But one of the tubes for the pipes was quite gunked up with stuff.
-
the exhaust is little more than a few 13mm? bolts 2 at the front 2 at the back 2 on each of the exhaust primarys and one just below the rocker cover but as before the job is infitessimally easier if you remove the rear panel of the car.... just work you way round all the bolts (its also easier if you remove the carb as well....)
-
Carb has been removed. the 2 at the back of the engine are annoying, I have got one out ( the top one ) but wheres the other one?
Also in the manual it says that ( what to me looks like a thermostat housing ) is the actual thermostat. Is this right? If so then where would all the pipes go when you come to put it back together. It may sound stupid me asking but I don't know much about these cars.
-
I assume the thermostat should be inside- to be fair ive left mine in...if tis not there someone has beat you to it!
as for the exhaust its easier if you take the rear drivers side wheel off and jack the car up to get the other ones.
if you are getting stuck take pics its easier for us to help then...
heres a couple of my "stripped" down pics if that helps-
(http://i7.photobucket.com/albums/y271/cheekos10/DSCN0992.jpg)
(http://i7.photobucket.com/albums/y271/cheekos10/DSCN0993.jpg)
(http://i7.photobucket.com/albums/y271/cheekos10/DSCN0994.jpg)
(http://i7.photobucket.com/albums/y271/cheekos10/DSCN0995-1.jpg)
(http://i7.photobucket.com/albums/y271/cheekos10/SS851397.jpg)
-
Cheers for that Stuey. I'll have another go tomorrow.
I have also noticed an arm loose on the carb but not sure where it goes or what it does. I will post a picture tomorrow so that you know what I mean.
-
I got the head off and the gasket was stuck to the block, so dug at a corner and then it started to come off, but fell apart. So I guess that means that it was definatly knackered as it was so weak? Just gotta clean both the head and block now as theres still loads of bits of gaskets still left on it.
For skimming the head, would I have to take out all the studs, valves and things in it or would it be ok to leave them in?
-
Also forgot toask, while the head is off do you reckon I should tow it to my local garage and get it pressure tested?
-
good work!!
ok from the top-
1 loose arm is usually the choke- lever the clip breaks..(identifiable by the fact its poking out the top of the carb andand should connect with the choke butterflys
2 the gasket has been sujected to years of heating and cooling they just break down its normal
3 the valves can stay in situ (see my pics above) just make sure that you clean the head meticulously prior to refitting. not sure which studs need removing as from memory there arent any on the head face?
4 not sure what you mean by pressure testing if you want to test the cylinders you need the head in place if you mean testing the head then most good engine shops will do this
-
My you guys like to complicate things, why dont you just take that engine out?? its half an hours work, makes any other work on it simpler/faster, and for example you stuey could have cleaned that tiny oil stain on your engine.... but when i think about it... you brits drink warm beer dont you? ah yes, that explains it all... :D :D :D
-
Thanks Stu,
Dont think the arm is the choke arm, it is situated at the back of the carb ( when looking at it fitted ) I will try to get a pic to show what I mean.
The thing that worries me is that it overheated, even though it didn't have thermostat. Surely something else could be wrong?
-
The thing that worries me is that it overheated, even though it didn't have thermostat. Surely something else could be wrong?
this my friend is starting to worry me... cos it means my gasket could be in grave danger... o-o.... :???:
does any of you lads know a simple way to check if the gasket had been replaced before, cos the previous owner told me it never was, but id like to check anyway...
-
Thanks Stu,
Dont think the arm is the choke arm, it is situated at the back of the carb ( when looking at it fitted ) I will try to get a pic to show what I mean.
The thing that worries me is that it overheated, even though it didn't have thermostat. Surely something else could be wrong?
Just make sure your cooling fan and rad are working correctly and everything should be fine. If one of these is shot it overheats and pop goes the gasket! Also make sure you put good 50/50 antifreeze in and when you refill bleed the system at the front to get the air out. Make sure your oil is at the right level as this aids cooling too. Hope this helps!
-
My mechanic mate said to me that it is best to use just water in the older water cooled cars, as antifreeze was no good for it. Not sure though?
-
The manual states 50%antif. - 50% water... :roll:
-
The manual states 50%antif. - 50% water... :roll:
Thats what I thought aswell, so wasn't sure what to do :roll:
-
Well think of it this way, wether you like it or not, or be it good for the engine or not, its going to get cold, so we have two options; put antifreeze in, or drain the system every day... :shock:
TBH, i dont see any reason why antifreeze could be bad for the car, it pervents rust, it prevents freezing, only one thing thou, if its aggresive, it could damage an old radiator or something...
-
I think with some older cars (triumph tag is a good example) they type of antifreeze was important cos it could hurt the alloy block but most modern antifree is fairly harmless stuff (tastes like crap tho!)
-
Well I put it all back together today, done an oil change and bleed the cooling system ( front and back ) and took it for a drive.
These cars are good fun on the road aint they? lol. But the temperature guage still seems to go up a bit too high for my liking, the fan does kick in for about 20 seconds but it does it way to late imo. I think I am gonna wire up the fan to a switch or maybe the ignition and more than likely have it running all the time.
I put a hose through the pipes before fitting aswell to make sure they were clear. The pipe on the manifold that the temperature guage switch was on that goes to the front heater was very blocked so I cleared it through.
So where abouts on the temperature guage do most of your bis's run at?
Mine seems to go between the last 2 white lines before the red bit and sometimes more.
Also should the head be torqued down different because the head has been skimmed? We did it to 50NM just to make sure, what do you guys think, will this be ok?
-
Congrats for putting a nother Bambino on the roads.. :smt041 :smt041
you are right, these cars are really fun to drive, maintain, clean... well they are... :D Hope you have much fun and laughs with it... :wink:
as for the cooling, it really sounds a bit late for the fan to kick in at that stage, mine starts right about here...
(http://club126uk.co.uk/forum/userpix/559_DSC04848_1.jpg)
it only went once near the red line (i was overtaking a concrete mixer up a steep hill, going 50km/h in secon gear... :D :D ) and then when i stopped steam started coming out of the filler cap, it didnt over heat but it was really hot...
Try taking out the two stage switch on the radiator, and cleaning it, then see how it goes...
-
Ok thanks for that Gordan.
Where abouts does your car run on the guage from just just running around town and things? Is it the same place?
Because if it is then something must be wrong with mine, as it always stays way over half way.
-
Yes, the red line is the normal running position when driving around town, during summer, during winter, it hardly reaches even that... (this is roughly where the fan pops in....) :wink:
Just had another idea, try taking out the heat indicator thingy on the engine, and checking/cleaning/replacing that... perhaps its just showing the wrong temp?
(http://club126uk.co.uk/forum/userpix/559_DSC04834_2.jpg)
-
I've wired the fan up to a switch now in the dashboard, and all's good. When it gets hot I just whack the switch on and then its ideal.
But it never runs at as low as you have shown on the picture. I thought I read somewhere that just over half ( 3 quarters ) is about right.
-
:smt102 But i never blew a head gasket, now did i? :P :P :D
-
Fair enough
-
The manual states that the fan starts: 1st speed 96-100C° 2nd speed 101-105C°. So if you divide the scale on the instrument to 70,80,90 and so on, youll se that mine starts at the correct temp.
(http://club126uk.co.uk/forum/userpix/559_untitled_1.jpg)
the red lines are 80,90,100,110,120 C°
-
(http://img205.imageshack.us/img205/5312/50179820wt3.jpg) (http://imageshack.us)
(http://img205.imageshack.us/img205/50179820wt3.jpg/1/w839.png) (http://g.imageshack.us/img205/50179820wt3.jpg/1/)
-
glad you got it back together and working again, I usually put the blower on if starts getting hot but mines normally a bit hotter running the Cro_126bis's gets so I dont think youve much to worry about.