Club126UK

Fiat 126 Chat => Tuning & Customising 126 Models => Topic started by: Dom on December 14, 2006, 04:36:10 PM

Title: Different seats
Post by: Dom on December 14, 2006, 04:36:10 PM
Hello all

Does anyone happen to know if the Cobra Classic bucket seats will fit into a fiat 500?  Would be great to hear from anyone who has succesfully fitted these or a similar seat. I currently have 126 seats in my 500, is it possible to use these existing subframes and mount them to other seats, or just use the original runners, without the tilts?

Thank you and a happy Christmas.

Dom
Title: Different seats
Post by: Chris Lakin on December 14, 2006, 05:45:48 PM
hi there Dom

look at this

(http://www.dropshots.com/photos/73614/20060810/225004.jpg)

is that what youre after?

this is from Dav126's aircooled 126 more pics of his car can be seen in the garage section of the forum under 126dave, hes away at mo but try sending him a PM

regards

Chris
Title: Different seats
Post by: Dom on December 14, 2006, 09:17:02 PM
They're the babies.

I did see that pic, so I knew it was possible, but seeing the wonderful feats Dave has already achieved, i thought perhaps some modification may have been involved. Modification beyond the likes of a layman like myself
Title: Different seats
Post by: Chris Lakin on December 14, 2006, 09:23:10 PM
i dont think its too hard Dom, you get the old sub frames and you can bolt the seats onto them i believe, well i know thats one way of doing it, not sure how dave did it though.

regards

Chris
Title: Different seats
Post by: 126dave on December 17, 2006, 02:56:10 PM
hey ho all,my seats came with the cobra runners........all i did was bolt some alloy sheet into the original floor mounted runners,then bolted the cobra runners to that........so the car is unmolested upart from some well painted rust treated holes throught the centers of the floor mounted runners....they work out lower than original.you may then want too lower your steering column.dead easy to do
Title: Different seats
Post by: Dom on December 18, 2006, 01:32:18 PM
Cool. Will try that, but before i do, is there any chance that the cobra seat will fit onto the old 126 seat's tipping base, or do these not come off?

Am will puick the seats up later this week. They came off a classic mini and come with the runners to fit the mini. Are 500s/126s compatable with these runners or are they completely different?

Thanks for all your help,

Dom
Title: Different seats
Post by: bis13 on December 18, 2006, 03:51:40 PM
hi mate i have spare seats so if you want a spare base to play with and experiment i will let you have one no problem. is your car on the road? if so we could get chris out for a drive and meet up somewhere, cheers mick
Title: Different seats
Post by: Chris Lakin on December 18, 2006, 06:12:19 PM
yep im up for a little trip, i will look forward to it, give me a time and place i will be there ;)
Title: Different seats
Post by: Dom on December 19, 2006, 01:22:48 PM
The car is on the road, but is due into the body shop anytime soon, to mend some accident damage and hopefully some annoying rust. Will definitely have it back in in the new year, but hopefully before. Still haven't picked up the seats as I bought them on ebay and they are quite far away, in Ashford, Kent.

Would you guys really wanna meet up with a 500 owner!? I have a 126, but it needs too much work to get it back on the road, and I have neither the time nor the expertise right now. Nice car though.
Title: Different seats
Post by: bis13 on December 19, 2006, 02:45:37 PM
tell you what i can do for you , your seats are in ashford , let me pick them up and me and chris will come down and see you ? nowt wrong with a 500 owner, let me know cos its not that far from me .
Title: Different seats
Post by: Chris Lakin on December 19, 2006, 05:03:10 PM
sounds good that goes for anyone else who wants to come with us.

for a short trip

regards

Chris
Title: Different seats
Post by: Dom on December 19, 2006, 05:49:48 PM
That would be absolutely fantastic. I'd feel like i'd be missing out on the trip though  :sad:

If you could do that I would be most grateful. Where in London are you based Chris? Lets set the ball rolling. I still have to pay the guy you see, as he'd rather cash on collection than paypal, but he'd take a cheque.

Will the seats even fit in the back of a 126?

Exciting stuff

Dom
Title: Different seats
Post by: bis13 on December 19, 2006, 06:04:44 PM
well fortunately for you my car is like the tardis and i can seem to squeeze lots into it . just out of interest the seller of these seats did he have the name of something butcher by any chance? chris is in uxbridge by the way
Title: Different seats
Post by: 126dave on December 21, 2006, 06:26:20 AM
well dom,get them fitted,then you can make the most of the stunning (dry) roadholding of your 500.i tried to fit the 126 seat parts,but they are soooo much work its easier to make the sheet alloy interface(you can also use high quality 9mm ply).that lets you mount them exactly where you want them,you can sit in them slide them around to where you want then just mark position.
on mine they are a tight fit between the b post and the tunnel,i fitted them right back and binned the rear seat squab and backrest.(heavy items and not used) i also fitted the drivers seat at a slight angle to suit me.
as they are abit lower,you may want to drop the steering,dead easy,just make up some spacers,the U/J in the column takes the slight change in angle perfectly ok
have fun!!
Title: Different seats
Post by: Dom on January 09, 2007, 04:23:53 PM
So here's the thing, I have the seats and am still trying to figure out the best way to put them in. I think I am definitely going to go with Dave's metal sheet across the old runners idea. After completely butchering an old 126 seat with the angle grinder to no avail.

I am still clutching onto a tiny bit of hope that I may be able to put this metal sheet directly onto the old runners and then carry on as you have done, so as not to put anymore holes into my floor. I am starting to think this is pretty impossible the more I think about it.

Dave, how many holes did you put through the floor between the old runners? And did you use any special washer or strengthening bar under the floor?

Any chance you have any pictures of your work - I am a complete novice when it comes to non mechanical modifications.

As far as MOT's go, is there anything I should be careful about regarding this?

Thanks again,

Dom
Title: Different seats
Post by: Bruce on January 09, 2007, 08:12:58 PM
Quote from: "Dom"

As far as MOT's go, is there anything I should be careful about regarding this?

Dom


Yes, if the seats tilt to allow access to the back seats do make sure they do not move and are locked down, when not tilted.
Title: Different seats
Post by: Dom on January 25, 2007, 10:52:24 PM
I have finally made some progress in puting in the new seats. Its not done yet, but will hopefully be done by the weekend!

I have almost finished the modified runners/subframe/interface thingy, just need to do a little more welding, but the difficult bit is done and prototype runner ready.


(http://fiat126club.co.uk/forum/userpix/332_RIMG1049_1.jpg)
(http://fiat126club.co.uk/forum/userpix/332_RIMG1050_1.jpg)
(http://fiat126club.co.uk/forum/userpix/332_RIMG1052_1.jpg)
(http://fiat126club.co.uk/forum/userpix/332_RIMG1053_1.jpg)
(http://fiat126club.co.uk/forum/userpix/332_RIMG1054_1.jpg)

The above pictures show the runner with the solid steel bar welded to it. This will be done to all four of the runners I have cut off the old 126 seat. You can also see the two holes tapped to fit M6 bolts. On top of this I will bolt down a sheet of strong ply, until i manage to track down a suitable metal sheet (which is proving almost impossible!)
Then I will follow in the same way 126Dave has done and mount the seat with its universal runners on top of this.
Not sure if anyone can forsee any problems with this method? Just hope this holds up with the weight of me and the new seats.
Cant wait!
Hope it works?!?
Title: Different seats
Post by: Chris Lakin on January 25, 2007, 11:30:39 PM
nice one Dom, looks like its coming along nicely!

have you thought about aluminium checker plating? You can get it in a variety of thicknesses. From most DIY stores

regards

Chris
Title: Different seats
Post by: bis13 on January 26, 2007, 07:40:00 AM
dom just go down to a local metal supliers and buy some thats what i do ,as for checker plate you will pay about 30 to 40 quid for a sheet of 3mm or 4mm  2 x 1 metre at a metal supplier .  i have bought some new seats to chuck in me car so  i shall be playing about very soon keep us posted on how you go cheers mick
Title: Different seats
Post by: bis13 on January 29, 2007, 08:37:25 AM
i got it sussed , i bought some corbeau buckets and have found a way to mount the seats onto original fiat runners . no welding is neccesary but can be optional. i have done one and it works fantasticly. so today i will do the second and do a photo guide and post it .
Title: Different seats
Post by: Dom on January 30, 2007, 11:52:57 AM
Cool, looking forward to the photo guide. I have my seats in now, but it was not any where as near as easy as i'd thought, and is only a temporary measure, as they look a little awkward.
Also the 126 is about 2 inches wider than the 500. Not much, but crucial when it comes to puting in the seats as they are cruseched against the side and only move forward, only with a struggle and as for seat belts? not worked that out yet!
Title: Different seats
Post by: bis13 on January 30, 2007, 02:31:32 PM
this is on a 500 runner as i thought i would see if it worked on both types,(http://fiat126club.co.uk/forum/userpix/212_car_seat_1_2.jpg)
(http://fiat126club.co.uk/forum/userpix/212_100_0902_1.jpg)
(http://fiat126club.co.uk/forum/userpix/212_100_0931_1.jpg)
(http://fiat126club.co.uk/forum/userpix/212_100_0921_1.jpg)
(http://fiat126club.co.uk/forum/userpix/212_100_0928_1.jpg)
(http://fiat126club.co.uk/forum/userpix/212_100_0931_2.jpg)(http://fiat126club.co.uk/forum/userpix/212_100_0935_1.jpg)
Title: Different seats
Post by: Dom on January 30, 2007, 08:13:28 PM
that is cool, and a hell of a lot less fiddly than mine. I have two sets of runners in use, both the original 500 ones (which are very stiff) and the ones that came with the seat. May try and make a frame up like yours, as my seats are sitting pretty high. Where did you get the metal from?
Title: Different seats
Post by: Chris Lakin on January 30, 2007, 08:19:25 PM
blimey thats great lol

they are identical seats to the ones ive got i think

looks simple too

how long did it take you Mick?

regards
Title: Different seats
Post by: bis13 on January 31, 2007, 03:12:21 PM
to sit and think about it and fabricate the first one took me half a day, to make the second about 2 hrs . take your time on the first and use it as a guide for the second the trickiest part is you must angle grind the original seat pivots and hammer them out then cut the outside part left away. secondly bending the flat iron for the front is crucial. the measurement between the two bends must be 395mm.

you will need 2 x 25 x 5 mm flat iron ( 2 x 1 m).

  2 x 25 mm x 25 mm square tube ( 2 x 1 m).

  flat iron cut to 2 x 375 mm these are for seat base and may differ from seat to seat (make).

  1 x 470mm flat iron    this is to be bent at either end.

 1 x 430mm square tube  

 1 x 314mm square tube

 m6 or m8 20mm bolts , nuts , washers.
 length of m6 or m8 threaded rod.
 drill good drill bits (flat iron is quite hard for crap drills beware !)

 mini grinder
 
 patience and a good supply of tea .
 

 all materials can be purchased from diy stores or metal suppliers .

 all the drilling is self explanatory and may differ from seat to seat , the positioning of anchor bolts may be a standard throughout all makes of after market seats i don t know.

   hope this helps a little , cheers mick




0
Title: Different seats
Post by: Dom on January 31, 2007, 05:39:39 PM
That is very impressive. I'm gonna use mine as they are for a bit, as am totally knackred from trying. But will eventually try and make the subframes like you have done if I can get hold of another set of 500/126 seats. Would be a cool touch if the tipping seat part could be kept in use - not that anyone could fit in the back with bucket seats!