Club126UK
Fiat 126 Chat => Tuning & Customising 126 Models => Topic started by: 126dave on June 25, 2006, 09:58:48 AM
-
hi all,i want to put some negative camber on my front end,im hoping to ''plant it'' a little better when under power thro the bends,im just kicking some ideas around at the mo,i'v heared of redrilling the kingpins and welding offset washers on,but,is there any easier way?.............i was thinking of machining some material from the ends of the top wishbone/removing some shims? :shock: ...what does anyone think of that idea?..........or does anyone have some modded kingpins/wishbones laying around??? :D .
id like to tie this project in for when my brakes finally arrive :roll:
-
well i think im going to go down the road of modding and welding the wish bones........i have some spare BIS ones to play with.im going to add some radical neg like my mates sunbeam stilleto had in the 70's.....
-
Dave
Are you going to do the backs as well? I am looking for the best way to put some neg camber on the back without lowering the car anymore as I have ground clearance issues until I get around to modifying the sump
-
hi Nigel,well,my rear end has a goodly amount of neg at the moment,its well planted,i will post some pics on ''slag my car'' lol.(does 126 suspension react different to 500 with 30mm lowering kit?,wouldnt think so...both the same?)........im just looking to give some attitude/handling to the front now.........by the way,are BIS upper wishbones the same as aircooled?......hope so.........by the way,are you thinking of dry sump mods to the 500.........shame im not based in the UK,id love to meet up an ''chew the fat'' with you
as a PS,car going really well for a 650 twin,more than happy with mods so far. :cool:
-
Dave
I have standard saggy springs at the back with AVO dampers, I didn't want to buy new springs untill I knew what effect the heavier engine would have on the ride height, it looks fairly reasonable at the moment. I probably need to work out the ideal spring rate and ride height and get some made up.
No plans to dry sump but was thinking about making the sump shallower but with added wings, baffles and trap doors, a bit cheaper that way.
I'm not sure about the BIS upper wishbones, I was toying with the idea of a fully rose jointed twin wishbone set-up with coilovers, Nanni do one but its quite pricey, I thought that kit car wishbones of some kind might do the job, still I'm supposed to be having a break from chopping bits up, I promised the my wife and daughters that I would give them some of my time for a while!
I would love to get together, if you ever get over this way let me know.
The tuned aircooled is good fun, ideal for where you are, no motorways to sit on for hours at high revs, and they make a great noise. :twisted:
-
yeh,i been wondering about the rear spring set up for your car,thats a hard thing to get right as per my other posts,good luck!,but your better placed than me for that!.i have some 650 springs here for free with 21,000 miles on them if you want to play with them?
your sump ideas sound good,and maybe add oil cooler from a 2cv or something to up capacity????
that double wishbone set up is great,but a bit £much£ for road use methinks.
i've already made up a slave BIS wishbone,giving 10mm at the wishbone neg camber,and have ordered a set of new 650 ones from gerstl (24ish euro each with bushes etc).............will keep all you tuners out there posted on progress
your correct,jersey is ideal for a tuned 650!.just need to sort my cornering out now!!....thats the secret as you know,keeping the loud pedal planted!!!..........does give mpg probs......tank full less than 80 miles :cool:
and.......our friend has sent another set of discs etc to me this week i think :P
-
can't think offhand how to do the back without lowering but the front is easier, there should be some spacers under the uper wishbones to give the wheels positive camber, taking these out will give you nagative. one thing to watch out for though is this will wreck your tyres; my de-ville had a bit of negative camber when i first got it and the tryes wore out at an alarming rate, they only lasted a few thousend miles. No amount of tracking adjustement would cure the problem and the only way i could fix it was to put more spacers under the uper wishbones.
The problem is you do not want the negative camber on the wheels when going straight, what you need to aim for is to have increased negative camber on the outside wheel and increased positive on the outside wheel when turning. this is taken car of by the suspesion geometry to a certain degree, increasing the caster angle of the front suspension can increase the negative camber on the outside wheel but it also increases the positive camber on the inside wheel.
What you need to do is move the bottom mount forward and/or the top mount back, moving the bottom mount will involve moving the spring which i don't think is practicle, but moving the top is a lot easier; to move the top back you must do exactly the same on each side. take the spacer from the back of the uper wishbone and put it on the front.
Do it a little at a time and test drive the car after each change, it will have the effect of making the steering heavier of lighter at higher or lower speeds, change it to much and the slow steering will be too heavy, and high speed will become dangerously skittish.
-
neg or poss camber should not increase tyre wear,excessive toe in or out will,your de ville must have had some problms with crash damage/knacked spring? to have had neg camber at the front???126's have pos front and rear when lightly loaded going to neg rear under load,tyre wear for the standerd car is average i think?.(like triumph herald /vitess/VW/spitfire?)
i wouldnt play with the shims on the top link at all,they compensate for body shell differences etc,if i had suspension /tyre wear probs id look else where before tampering with that area.
so my 10mm will still be correct as per the body shell,and the base trim from the factory will remain.i wont play with castor angle,way beyond my ability.
all my other suspension bits are new,im just adding neg with the front end realigned yet again.
-
yes mine had suffered some crash damaged, the tracking was spot on, and i cured the problem by putting some extra shims under the wishbones.
-
neg or poss camber should not increase tyre wear
It most cirtanly will. You end up with one edge of the tyre wearing more than the other and it wears alot quicker than normal as theres more pressure on a smaller surface area.
The more camber the worse it will be but you can help it by swapping the tyres around if they are symetrical ones
-
im used to high tyre wear on things,i run a 'blade and an SP1,SP1 can eat a rear (130ish quid) in 2-3 k miles :twisted: .......so a bit extra wear on the (relativly) cheap 126 tyres doesnt fase me at all....i still stand by the fact its tracking that causes most wear.
if we could keep this thread to the whys and wear (sic) fores of acheiving neg cam that would be great. :lol:
-
i wouldn't call the tyres on my 126 cheap, the 165/55/13s i have cost more than the 205/70/14s i used to have on my 280SE, granted they are not the same price as tyres for big bikes, but when you need 4 the price is actually more.
-
top track arms are on order from gerstl(yet another back order tho)..when they come im going to drill and weld then as per my jig,i'll let you know in due course if my tyres wear radicaly,but to be honest,if i can cure the bump steer thro the fast corners i really do not care about the tyres.................but,i gota say this,as for neg or pos camber affecting wear,i really dont see it,my bis has both,and tyres wear evenly,even driven hard like it is.........time will tell tho on the more radical neg im aiming for.......... :cool:
-
Now thats what I call negative camber :shock:
(http://home.btconnect.com/CPR-CREATIVE/1108/Acoord14.jpg)[/url]
-
:shock: well bruce,id def agree there would be some inner edge tyre issues there!!!!!!!!!!!!..........
-
A few taste issues me thinks as well...
-
Wow. How is it possible that people spend so much time and money on total plop? :???:
-
My idea of negitive camber, pitty its only a mock up for now (on the front)
(http://img.photobucket.com/albums/v469/slater3333uk/Dsc00329.jpg)
Before you guys go slagging off evereyone who dosent have the same tastes as you then maybe you ought to consider you own a FIAT 126! which 99% of people would consider one of the most 'plop' cars ever conceved!
:!:
-
Good point, but as 126 owners, we also know we are right :lol:
But seriously - wasn't refering to the taste issue, more that despite clearly having had a shed load of time and money spent on it, there's a basic issue with the arse end... and the clearance is about 1mm. Maybe I came over wrong.
If I had been commenting on taste I have used an even stronger word than "plop" (if I knew one) :???:
-
Im not a huge fan of it but it is a bloody good car, lots of skill involved and it looks totaly MAD! (thats the point) you will probably find its juiced too so if you want to drive it anywhere just raise it a touch and your off.
What i do know is negitive oppinions about other peoples cars are a bad thing. I dont think anyone has a totaly open mind and thats fine with me so if you dont like it then keep your mouth shut like i do (most of the time :lol: ).
-
What i do know is negitive oppinions about other peoples cars are a bad thing. I dont think anyone has a totaly open mind and thats fine with me so if you dont like it then keep your mouth shut like i do (most of the time ).
Ooops i'm upsetting people again!!! Must remember not to express any light hearted opinions about anything again for fear of causing offence. :smt005
I do hope that this does not turn into one of those pathetic forum tiffs that just serve to devalue a great site like this.
I am sure that the car is very clever and been built with lots of skill but in my opinion – if I am permitted to express one – it's very amusing, I feel sure that the owner must have a sense of humour, you would have to to spend a small fortune on something like that.
I have got used to people taking the piss out of me and my car, big fat bloke – tiny car, big farty noise (the car - well most of the time) big engine hanging half out the back. It's part of life, I suggest you get over yourself or take your own advice.xxxx
-
not keen on the car, car modification of that sort is becoming so common its nolonger stylish as it once was considered, its boring, i'd rather see something original or different in its own right. but as most here would agree the time and skill needed alone to do something like that is amazing.
the problem is why cant people slate each others cars, i wouldnt give a t@ss if someone slated my cars, i get it most days any way :D
Thats my oppinion i'll be at the uxbridge autoshow this sunday if anyone wants to fight me over my views :lol:
Chris
-
I just dont want this place to end up like most other 'one make' sites where everything other then the make in question is considerd 'plop' Everyone is narrow minded and doesnt take any inspiration from any other car scenes.
All the cars will end up looking crap and you wont be able to post a pic of anything differant for fear of it being ridiculed.
It all happens because people on the internet feel they can speak thier mind whenever the hell they like cous theres not someone standing their thats going to smack them one. If you went to a show and started walking around slagging off every car you dont like then i think you'd feel the conciquences pretty quick.
What this forum and the Fiat 126 in general needs is a big injection of alternitive influance. You should be looking at cars like that (and examples of other styles and makes) and taking a bit of inspiration from them then someone might attulay get on and build a decent 126!
:wink:
-
yer i see what you are getting at now m8,
i would hate anyone "fearing" they would be ridiculed by what they post.
You are right though, the internet/forum causes a lot of problems, people become too confident with airing their views against other cars/makes/models/modification etc. However thats what a forum is for???? Sureley? Its all done in a light hearted manner, no serious slagging. If you dont want people to speak slater there isnt going to be any posts on here!!!!!
We have a decent 126's adding gull wings and crap to it isnt going to make the car any better?
but lets not make an issue out of this, please
lets just enjoy it all! :D :D
-
Sorry to blow it all out of proportion, i do understand its only light hearted banter
:)
Now back to camber issues :cool:
-
i noticed Michael's 248 has a fair bit front wheel negative camber, it seems to have more than most of the other cars as it seems this car is the one i noticed it on the most. also if you check out the tyres when he pits or at the end of the race the front tyres are worn a lot more on the inside edge.
-
slater,thats a lot of neg,im interested how you plan to achieve that,the most that can be achieved without some serious re engineering is 10mm at the top control arm............that looks good tho!!!!!
bruce,yes,an F1 car like shueys will run what ever is needed for lap times to drop...................im using the same logic.....im down to 90ish miles from a tank of super with lead added..........dont care.......cars running and sounding superb!!!! :cool: and if i can improve the feel of it thro 'fast' bumpy curves so much the better.......
everyone to their own,if you want tyres to last 30,000 miles and get 160ish+ from a tank of supermarket fuel,no problem as far as im concerned.
after all,thats what my pooter Bis is for................ :D
-
tbh i dont think i will have camber on the front, i was just messing about a bit. It could be done tho i think. Shorter top wishbone extra long bottom wishbone and move the shock top mount towards the centreline of the car.
What im relly planning to do is keep the wheels upright, fit skinnyest tyres i can get my hands on. Shorten the top wishbone about an inch, loose the leaf spring and mount a lower wishbone in its place, use coilover shocks with the shock mount raised about 5" inside the bonnet to stop them bottoming out.
Basicly its going to be a drag car but more for comic value then attualy going fast! :cool:
-
my car is 5hit , i don t care , if you tell me , i dont care , your car is 5hit , i dont care , if i tell you , i dont care, do you care? its a game enjoy playing it. ACTUALLY I THOUGHT I HAD BUILT THE ULTIMATE pooTER........but it looks like i could be wrong ......he he
-
nah, you tried building a shi**er but ended up with a cool car!
-
well,new top links welded and redrilled 10mm in,if i can finish my bike rebuild :shock: im going to fit the new brakes and top links this weekend....i'll keep you all posted..........................................................however,there was talk tonight of a fruit de mer tomorrow....so things may slip a bit :lol:
-
well,that 10mm makes a difference,low speed testing today with new brakes(another story)....very sharp turn in and still good feel and lightness,an easy mod to do,and cannot wait to see what its llike pushing thro the curves! :cool:
-
Hudsonhenry!
Nice body kit, never seen one of them fitted on a 500. Looks nice, very nice. :lol:
-
Dave
Have you got any pics of your mods to the top links?
Did you use shims of the final adjustment?
Nigel
-
hi nigel,i did not touch the factory shims,i made a simple jig that fits acuratly in the new uncruddy top link,then after filling (with weld) old holes,simply drilled new ACURATE holes 10mm in........so,everything should be still factory,but with 10mm added..........i think that is more than ok engineering for my modest BHP.....didnt take pics,too much greif loading on the site here for me!.
also means that original parts are there in case my theory goes pear shaped!!
the jig was just a bit of flat i had kicking around the workshop,10mm seems the max,the top link bows out to the body end so there is a limit to what you can do easily.....im impressed with the turn in tho!!!
-
well,....davys on the road again......as the song says...........,the neg camber is very good,......my favorite hill now is easier to climb,the front really sticks,really stays on line.........so far so good,nothing has broken............
this is coupled with neutral toe in/out at the mo(may go stock yet),and also lowered springs/cut down mounts/all new bushes/uprated shocks etc,i would'nt advise this with standard suspension parts...... :cool:
(http://www.dropshots.com/photos/73614/20060912/b_103329.jpg)
pic added by C.Lakin for Dave[/img]
-
thanks chris,now boys and girls,you can see the results of the 10mm surgery :cool:.......bear in mind there is a little steering lock on in the pic tho....it does'nt toe out that much!!!
-
http://img135.imageshack.us/my.php?image=dscf1010mediumtu6.jpg
http://img53.imageshack.us/my.php?image=dscf1012mediumqa0.jpg
viva la negativ :lol:
-
when you described it Dave i thought it would look more drastic, looks like a nice little mod youve done there.
regards
Chris
-
btw nice looking automobile, Dave!!!! rear mirrors are vitaloni??
-
thank you guys,yes valentino,vitaloni californians......gorgeous,transform the car in my opinion
-
are these the mirrors, http://www.superformance.co.uk/index.htm at the bottom of this page? i was thinking of getting 'em for my little car to replace those horrible plastic thingys, replaked the nasty looking wheels, now its let down by the mirrors
-
thats them bruce,demon tweeks do them as well,same kinda money
-
cheers dave, I'll order the Ferrari ones they are a bit cheaper. do they scew on from the outside, and will the original mounting holes posiiton suffice or do they bolt on from inside the door?
-
they are fixed from the outside,and cover the original holes,mine had the mirror bolt head showing at the front when installed,i plugged the hole with black silicon.....you'll see what i mean when you get them.mine might have had little plugs,but if so were missing.
the glass is adjustable inside the housing,the quater lights do obsure a little,but,hey,what price is cool?...................... :cool:
-
yes they do look very smart, loads better than the naf ones on there now, plus one of mine has the wrong glass in it, so this is a good reason to replace the mirrors. can't remember if the quater lights got in the way of the standard mirrors, but then what price style, as they say.