Club126UK

Fiat 126 Chat => Tuning & Customising 126 Models => Topic started by: 126dave on June 01, 2006, 07:54:42 PM

Title: cams
Post by: 126dave on June 01, 2006, 07:54:42 PM
im looking for a fast road cam for my (slammed)mobile chess board,ive been let down by gerstl,and nanni ricambi do not answer emails.........and as for middle barton ripoff.,well...........so,does anyone sensible have a sensible suggestion for a supplier?...............................as usual,willing to swap fresh cooked (jersey) lobster for info :wink:
Title: cams
Post by: Chris Lakin on June 01, 2006, 08:12:25 PM
have you spoken to Dajwid? there must be loads kicking about in Poland!

how much does it cost to have the standard one sent away to be modified? can it even be done to a standard cam?


regards

Chris
Title: cams
Post by: 126dave on June 01, 2006, 08:27:13 PM
hi chris,yes they can be built up and reground and case hardened,but,i pulled engine down with gerstl promising a cam,only to wait 5 weeks for them to say it was unavailible.........................that was after they suggested the ''360 degree'' cam that i should order............
i just want something off the shelf that wont melt,Nanni are good,but they dont want my money.....have mailed and mailed,i want oil cooler and other stuff as well,but just cannot get a reply.......big stack of euros here waiting. :roll:
Title: cams
Post by: Chris Lakin on June 01, 2006, 08:56:51 PM
i realy cant understand these companies, is it they prefer local buyers? and cant be bothered to post? i cant get my head around it.

its going to be expensive to get the standard cam modified, so yer i think youre rigt aim for an off the shelf cam. Have you tried Ritz? they do tuning stuff too,  ive heard there very reliable, but never bought from them myself.

http://www.fiat600.net/

Chris
Title: cams
Post by: slammed 66 on June 01, 2006, 08:57:40 PM
Hi Dave, look ive appologised mate so lets leave it out eh?
I dont know for sure but i'd guess Kent cams  http://www.kentcams.com/  might be the people to try as they have done a cam for just about every car made at some point.
They will probably have to grind one fresh from an old or stock shaft but i guess you never know till you try.
Regards
Ross
Title: cams
Post by: 126dave on June 01, 2006, 09:22:03 PM
thanks Ross,i just assumed what with the prices they (nanni/gerstl)are asking they would at least want to sell something!.........im still looking for something ''off the shelf''.....at 200ish euro(just a 2cyl cam!) you would think nanni would answer my mails?.......and dont get me started on the oil cooler/converted timing cover prices!!!................i cannot it seems,spend my money,despite there ''worldwide postage'' claims.
Title: cams
Post by: slammed 66 on June 01, 2006, 09:27:47 PM
Yeah, i can see how waiting 5 weeks for nothing could be frustrating :x
Not anyone in the states that could help?
Title: cams
Post by: 126dave on June 01, 2006, 10:01:15 PM
you are right Ross,im very pissed off, engine on the bench in bits........new bucket seats,rev counter,oil gauge etc fitted......all was timed (pardon the pun) to get car back on the road with carb reversal sorted,oil cooler and new cam.........and three weeks leave from work wasted........................................................1 week to go an no bits to fit. :twisted:
Title: cams
Post by: hudsonhenry on June 01, 2006, 10:54:31 PM
Dave

Have you tried Ruud?

I have a 40/80 cam which I can highly reccomend

Nigel
Title: cams
Post by: dajwid on June 02, 2006, 07:16:37 AM
Hi a brand new one is 8 pounds un modified.

http://allegro.pl/item106339799_walek_rozrzadu_fiat_126p_elegant_nowy_okazja_.html

 A company near my school does this type of work, what is it you want done and I will ask them for a quote.

I'm pretty sure you will get plent of change out of your 200 Euros :lol:

A friend has an oil cooler for a 126 too used but for a very short time if you are interested.
Title: cams
Post by: PaulB on June 02, 2006, 07:45:53 AM
http://www.500mania.it/english/prodotti.php?idcat=16
Title: cams
Post by: 126dave on June 02, 2006, 07:53:12 AM
hi Nigel,well,ruud has been very slow as well,brakes (paid for) still waiting.............some 5 weeks later,remember the post? i paid thet week..........all i get is dutch language email saying back on 6th june!!!!

nanni have a great 40-80 with timing chain/gears,already (aparently)dialed in,i dont fancy elongating the holes and welding myself......article 0404f

david (poland).if that oil cooler has the modded timing chain cover with oil filter cartridge id def be interested...even polish ACM racing do not answer mails......i've even switched off my mail washer just in case they were being pinged!!

Chris,have mailed ritz.lets see if they can be bothered to take a 600ish euro order eh?
Title: cams
Post by: dajwid on June 02, 2006, 09:05:47 AM
Ruud are not very reliable, they asked me to get parts for them here then I had a huge job getting in touch with them again.

Oil cooler can be seen here.
http://allegro.pl/item105279328_chlodnica_oleju_wraz_z_filtrem_do_mocnego_126p.html
It is about 75pounds.

A modified cam is about 40pounds
Title: cams
Post by: 126dave on June 02, 2006, 03:50:15 PM
hi david,i checked that cooler out,it looks just a remote oil filter to me?,think i'll give it a miss.but,can you get standard rear and front rubber engine mounts and engine gasket sets cheap david? if so i would take 2 gasket sets and i complete engine mount rubber set.can forward funds to you by paypal or whatever you want if you can do that

Chris,ritz got back to me.....500euro :shock:  for oil cooler kit,cash up front before they MAKE it!!!!????????.

anyhow,i've taken the plunge an ordered from nanni.....im hopeing that 634euro :shock:  order might wake them up :roll: .
last big order .......................lets hope the car is back on the road this year!!
Title: cams
Post by: dajwid on June 02, 2006, 04:41:52 PM
I'll get them this weekend and pop em in the post. PM me your address.
Title: cams
Post by: 126dave on June 05, 2006, 09:20:16 PM
totaly edited,just me being frustrated at not havin my little car!!!!!!!!!!!!!!!!.
sorry to anyone who was slighted in anyway
Title: cams
Post by: PaulB on June 05, 2006, 10:58:46 PM
try pasquale at turbo1sport - he sent me photos of everything laid out before I paid him. Top man. Also found 500Mania quite quick and not too badly priced.
Title: cams
Post by: hudsonhenry on June 06, 2006, 10:03:23 AM
Dave

I have a whole engine that I am thinking about selling if you are interested.

I have now fitted the 1108 fire engine into my 500 and should have it running at the weekend. If all goes well I won't be needing my aircooled any more. I spent a fortune on it and its quite nippy (Chris has been for a spin with me, ask him)

I will give Ruud a chase for you, I have always found him to be realy good, will let you know

Nigel
Title: cams
Post by: hudsonhenry on June 06, 2006, 10:16:34 AM
Dave

I have just spoken to Ruud, He has just got back from a fortnights holiday in Greece. He says he posted you brakes two and a half weeks ago, he is going to pop home and get the post reciept and email you the tracking number.

Hop this helps

Nigel
Title: cams
Post by: 126dave on June 06, 2006, 01:06:18 PM
hi nigel,yes,ruud has sent me a mail explaining all,his vacation timing coincided with the brakes going missing,so a public apology from me is in order  :oops:

as for your motor,well,im well into mine now,i would have bought it a few months ago tho!,it is fun tho frustrating at the same time!
Title: cams
Post by: 126dave on June 15, 2006, 07:31:46 PM
star date 15...06...06.captains log............well,parts turned up from Nanni......engine rebuilt,all lookin pretty,just have to ''adjust'' rear engine mount to clear modded timing cover/oil filter housing.................................then plumb in oil pressure gauge and oil cooler etc..hard wire the rev counter and the car should be running again,sadley,my brake kit seems to have gone missing in the post tho  :cry: ..........................
Title: cams
Post by: dajwid on June 15, 2006, 10:19:58 PM
Silly question, how much has gone into your little 126 so far? (we won't tell the wife) :lol:
Title: cams
Post by: 126dave on June 16, 2006, 06:38:57 PM
dunno how many £ or euro...............i learned a long time ago not to keep accounts of the cost of love affairs........................................ :lol:
Title: cams
Post by: dajwid on June 16, 2006, 09:41:20 PM
Are you talking about the wife again?
Title: cams
Post by: 126dave on July 06, 2006, 06:21:59 PM
well i can report the car was running very well with new cam /oil cooler etc etc etc installed......i say was,because the dreaded vibration has destroyed my MK.3 attempt at a carb steady...so top engine tin off again,re braze and reinforce from below,then respray etc etc.......... :roll:...........still,it gives me time to play with my front suspension
Title: cams
Post by: hudsonhenry on July 06, 2006, 10:04:39 PM
What carb are you running?
Title: cams
Post by: 126dave on July 07, 2006, 07:35:20 AM
hi Nigel,40 DCOE,mounted on pirelli spacers,and suported  at the other end by a custom brkt mounted under the ram intakes,the bracket in the last ''tipo'' went down through the top tin,(brazed and extra metal collar added) then turned and sat on the second skin in a pool of silicon to try and dampen any vibes......
somehow the top skin has fractured around my reinforcing metal.....by the way,all the above was done with the motor on the bench and everything was ''relaxed'' as it was fabricated.also,the motor has not been ragged since fitting,still running in the cam etc.

any ideas most welcome,
meanwhile i am going to strip it out and ditch the silicon idea,braze another plate across the bottom skin,then refit all the other bits.......i do get the feeling im going to be chasing this one for a while..............

i will beat it!!  :twisted:
Title: cams
Post by: hudsonhenry on July 07, 2006, 09:21:04 AM
Dave

I used to have a twin choke Delloto DHLB on my aircooled, it was supported by a bracket coming off the plate that the air filter attached to, this came down about 1 inch then turned 90 degrees, attached to this was a rubber and metal exhaust bobbin. The bottom of the bobbin was bolted to a 'u' bracket which was welded to the top of the shroud. I don't know if this makes sense but I will try to dig out a picture for you. This worked well as the bobbin acted as vibration absorber. I did have to occasionally replace the bobbin as the vibration would eventually seperated the rubber from the metal but it only took a couple of mins compared to hours of stripping and re-welding.

I solved the problem completely by dropping the twin choke and using a FZD, this was far superior to the twin choke, gave more peak power and a much better curve throughout the rev range. We tried lots different venturi sizes on the twin choke and had it working quite well but it was never as good as the FZD. The problem we found was that unless we used smaller venturies the peak power came in far too high up the rev range.

Are you using a Panda 30 twin port head? if so then a choke per port is a good idea, if you have a single port head then there is no benefit to using a twin choke.

The other thing that contributed to less vibration was having the engine balanced.

Hope this helps

Nigel
Title: cams
Post by: 126dave on July 07, 2006, 06:31:49 PM
hi nigel,thanks for the input,yes,im running a panda 30 twin port head,slack day at work today,so all is brazed/painted and ready to go again,fitting all tomorrow.

the reason i didnt go down the 'bobbin' route was because the carb was vibrating too much already,causing reversal,i needed a firmer fixing,the system i had worked great till it broke.......................

anyhow,all done now and back on the road tomorrow...........i also found the bell crank for the (standard) throttle linkage was vibrating,so ive drilled and tapped that,and fitted a cute little grub screw with a ball in the end to preload the linkage

as for dif carbs etc,no rolling road here,so im just giong on accepted 126 euro folklore on whats what to fit. it looks goes and sounds well with the bits i have fitted,bogs a bit from idle but thats ok....sounds great when on full throttle,cannot wait to wind it up a bit more,i will be keeping a red line of 5000ish for my un balenced motor
Title: cams
Post by: hudsonhenry on July 07, 2006, 07:48:50 PM
Dave

Hope you have sussed it. I tried a few different methods before the bobbin, it was the only method I could find that did not move too much but also did not suffer from stress fractures.

(http://home.btconnect.com/CPR-CREATIVE/1108/bobbin.jpg)

And a couple to make you smile (or gag)  :shock:

(http://home.btconnect.com/CPR-CREATIVE/1108/cos1.jpg)
(http://home.btconnect.com/CPR-CREATIVE/1108/cos3.jpg)

Nigel
Title: cams
Post by: 126dave on July 07, 2006, 08:33:57 PM
cool nigel..........not sure about whats left of that 500,they so cute,why do that?...

anyhow,one more try down my route,i have another top tin coming i hope,if i need to i will try your method...............good pic,i like your detailed workmanship,very nice to see that attention to detail,you know what i mean. :cool:
Title: cams
Post by: Chris Lakin on July 07, 2006, 08:34:55 PM
what the hell they have put the engine in the front!!! is that the body shell on a chassis?

regards

Chris
Title: cams
Post by: 126dave on July 07, 2006, 08:38:12 PM
god knows chris,twin cam somthing,prob alfa/fiat,,,space frame maybe?..very nice i expect but not my cup of vino.....................nice pic tho nigel!
Title: cams
Post by: 126dave on July 11, 2006, 07:36:07 PM
update,motor holding together........running well,am thinking of lightened balenced flywheel and fan from nanni next....any thoughts anyone?   :cool:
Title: cams
Post by: PaulB on July 11, 2006, 09:59:38 PM
Why not use a 500 flywheel?
Title: cams
Post by: 126dave on July 12, 2006, 06:09:28 PM
mmmn,had not thought of that,is there a lot of difference in the two??......and,if so,,who has one going spare??
Title: cams
Post by: hudsonhenry on July 12, 2006, 06:45:35 PM
I didn't realise that the flywheels were any different. :shock:

As I understand it the flywheels were balanced with the cranks (to a degree)  so any new flywheel will need balancing. This should be done with the crank and the oil filter assembly for best results.[/i]
Title: cams
Post by: 126dave on July 12, 2006, 07:15:16 PM
ahh......learning all the time.........
Title: cams
Post by: hudsonhenry on July 12, 2006, 07:56:05 PM
Quote
ahh......learning all the time.........


Tis true...... now where did I put that book on exhaust design and fiberglassing?????
Title: cams
Post by: PaulB on July 12, 2006, 09:58:33 PM
I've just weighed a 500 flywheel on some very crap scales and it came in at 6kg. If you like, I'll try and find something more accurate as i think those scales are off. My flywheel isn't available I'm afraid, but maybe Richard has one? or ask on the 500 board.

I think the Abarth 595 flywheel was 5.6kg, but i've heard of them down to 3kgs. I'd be worried about one that light in a 126 as they serve to dampen vibration as well as provide momentum.

I read somewhere that flywheels where different between early and later 126s.
Title: cams
Post by: 126dave on July 13, 2006, 09:48:27 PM
hmmnn...i only thought of a lighter fly wheel because my little motor is not as 'snappy' on or off the throttle as id like.....makes fast changes/double de clutching down a bit cumbersome............pedals are perfect for heel an toeing,but motor is not quite up to it........ :cool: